That was a brilliant video mate. Very clear instructions, step by step, no bells and whistles. It gives someone with no experience the confidence to do it give it a try. Keep up the great work.
@tootsielucas9393
6 ай бұрын
As a women watching this and trying to change her own brake pads. Thank you so much 🙏🏾🙏🏾
@TehBr0
Жыл бұрын
Another excellent video, this will save money for so many people, your ability to instruct viewers is tip top.
@marcjcapetown
Жыл бұрын
You legend! Was just quoted R2100 for the front pads alone, bought some Bosch pads for R600 and will fit them myself. I'd better check the rear pads too, the jury's out on whether I'll tackle those, I'm guessing you kept the swearing in check for the video, while doing those!
@brettbates552
9 ай бұрын
Thanks for this video mate. Your clear instructions made the process so easy. Can I add 1 thing though? If your drums are stuck on and can’t be wiggled off by hand, there’s 2 threaded holes that you can used to put bolts in and pop the drum off.
@jackiihope9108
Жыл бұрын
Thanks mate you uave helped me out of a pickle with my ute I'm binge watching your triton videos to make sure I no it for when it happens now thankyou very much top clear video
@adambartley7740
2 жыл бұрын
Thanks mate you made the job so much easier then i thought it would be
@NumanAir
Жыл бұрын
Thanks for this. I just did both front and rear brakes on my 2018 Triton. Drum brakes are fiddly had your clip playing as I was doing it. Great instructions. Any chance of a serpentine and alternator belt replacement 😊
@saulataani5861
10 ай бұрын
I agree would be great!
@truetierra
2 жыл бұрын
Great video mate, many thanks. Would love to see a front brake rotor change on the MQ at some stage. Cheers. 👍
@SpikyGussy1
7 ай бұрын
Just did front and rear brakes on my 2016 Triton. Couldn’t have done it without your brilliant, easy to follow video. Many thanks, really appreciated.
@Gary-vz2fk
2 жыл бұрын
Well done! Clear instructions and it is a lots easier than I thought!
@gregcapel6990
Жыл бұрын
Appreciate the vid, done heaps of disk breaks, but never had to do hub brakes, wasnt to bad, except i had to replace the small washer (you can get them from repco)
@pearsemcbride
6 ай бұрын
Excellent video clear and easy to follow . Just wish my calliper piston pushed back as easily as yours 😂
@saliyagurusinghe7148
2 жыл бұрын
Excellent video thank you. Just a minor edit, the engine in the MQ and MR is 4N15
@Kissmeshitfacedd
2 жыл бұрын
brillaint you've brought this out just as mine need doing! i've got a series 4 but i'd imagine its the same! Thanks for the Easy to Follow Video!
@ratapotamus
11 ай бұрын
I figured it would be this easy to change the front pads but thanks for confirming it mate 🤘
@mattnorton958
2 жыл бұрын
Great video mate! Will attempt to do this to my MQ with your help! Cheers! 👍🏻
@salvadormartinezderituerto1909
Жыл бұрын
Thanks from Spain. Very good videos, very good explained 😊
@frankm4120
2 жыл бұрын
thank god for You Tube, thanks for a detailed video, it is easier than I thought
@irwanmashadi7515
Жыл бұрын
Nice job. Can help to make video for changing rocker gasket cover full set. Thanks mate!
@avedis4227
2 жыл бұрын
Excellent tutorial mate. Would love to see a gear box service on this model.
@redenciomarcojos3806
2 жыл бұрын
Thanks for this very clear tutorial.
@rastislavzrelak9238
2 жыл бұрын
good video, I did front ones few times but I reckon back ones are next, thanks
@Trevwhitesailing
2 жыл бұрын
You have an excellent instructional style, nice work mate.
@kelvinmoffatt
Жыл бұрын
Wow, front's easier than I thought. I think I'll do it myself.
@DiHandley
2 жыл бұрын
Hey thanks for this! Brilliant video and easy to follow. I’m glad I subbed when I did! Cheers
@petewilliams4289
2 жыл бұрын
Excellent video, great explanation and details, thanks.
@jackrussellrambo5547
2 жыл бұрын
U sir are a ledge bro big greetings from 🇮🇪
@Naxas100
2 жыл бұрын
Thanks for the video mate! Well done
@colindiver8156
4 ай бұрын
Love it mate! Thanks just did mine came up a treat luv the vid thanks heaps saved me a bunch of money
@johncahill2309
Ай бұрын
how many people cut the spring with the sidecutters? shouldnt you use the pointys or at least say dont squeeze too tight...just my thoughts
@alexismichael854
Жыл бұрын
Great video and very helpful keep posting
@shaneoconnell2849
2 жыл бұрын
Awesome video mate, thanks for all the detail 👍
@enriqueramirezs5360
Жыл бұрын
EXCELLENT VIDEO, GREETINGS FROM MEXICO!!!
@RK.7796
Жыл бұрын
Thank you for your video. So good.
@RyanCowley86
Жыл бұрын
Absolute legend. Thanks so much
@RichieRich845
8 ай бұрын
13:22 that little clip is $20. each from Mitsubishi. Can they make it any smaller?
@mitcho8666
6 ай бұрын
Great video. Thanks heaps mate helped me a lot
@glenn8986
7 ай бұрын
Mitsubishi quoted me $987 for front rotors and pads fitted.
@RoDeCaM
2 жыл бұрын
Can you make a video for adjust the hand brake!?
@petersutton2182
9 ай бұрын
This should save me a few $$$, a BIG thanks 🙂
@toddc5451
Жыл бұрын
Do you have to remove the cap on the brake reservoir before pushing in the brake piston?
@driftcarsjp
Жыл бұрын
No
@adamcawthorne
9 ай бұрын
Great video, thanks for sharing. Q. Did you have to top up the brake fluid once the job was complete? My brake pedal is very spongy. It builds pressure, but then fades away. Can you help? Cheers Adam
@driftcarsjp
9 ай бұрын
Hi have you adjusted the brake shoes enough? Is the handbrake tight or come up a long way before locking on the brakes?
@adamcawthorne
9 ай бұрын
@@driftcarsjp All good, I’ve sorted it. Just needed to top up the fluid, and bleed the lines abit 👍🏽.
@rogercampbells5651
Жыл бұрын
thanks mate good presentation
@andrenarbey3569
4 ай бұрын
Great tips for the piston
@KevinHa-o8p
8 ай бұрын
Great video. Thanks.
@mrsamirg
2 жыл бұрын
Hi mate what was the part number for the Bendix brakes for your triton? I have the same model. Cheers mate.
@driftcarsjp
2 жыл бұрын
Ill find out next time I see my mate...
@LRG-c4k
2 ай бұрын
thanks mate
@123rhianon
Жыл бұрын
When u say put the car out of gear does that mean park as well
@driftcarsjp
Жыл бұрын
Yep have the car in neural.
@craigmountain5100
2 жыл бұрын
Would you mind running through a alternator belt replacement I can’t work out how to release the tension with the tensioner
@angusfindlater
2 жыл бұрын
Look inside the left hand side wheel guard and remove flimsy rubber skirt/flap and you can see an adjuster to slacken off. First you need to loosen the tensioner pulley center nut on face of pulley or the adjuster bolt will not move and the thread on the adjuster nut will get damaged. Take note of the belt route too.
@craigmountain5100
2 жыл бұрын
@@angusfindlater hi yes i think ive sussed it. Remove the first belt like you say then a 14 mm spanner on the tensioner on the second belt and with a bar turn the bolt in the middle of the tensioner wheel anticlockwise and the belt becomes loose. Am i right?
@craigmountain5100
2 жыл бұрын
@@angusfindlater to remove the fan belt
@angusfindlater
2 жыл бұрын
@@craigmountain5100 yes. Cant remember which way to crank the main belt tensioner as i was under the vehicle. It only goes one way though. One more thing.... use locktite on the second belt pulley nut once you have retensioned. I found mine became loose again after a while
@craigmountain5100
2 жыл бұрын
@@angusfindlater thanks findlater, it doesnt feel right turning the nut anti clockwise almost as if you will unscrew the nut before loosening the tension but as you say it will only go one way. I havent actually gone as far as removing it but the belt goes slack so i think thats it
@junetijam1670
2 жыл бұрын
how many turns you adjust the break adjuster?
@driftcarsjp
2 жыл бұрын
Until it locks up the brakes. You won't be able to turn it any more then you back off about 2 turns.
@Yhf6649
2 жыл бұрын
Fantastic,thanks
@lancegraham7722
2 жыл бұрын
Thank you
@lovelyhurlin6494
2 жыл бұрын
Awesome mate. Thank you.
@mathewfoley1531
Жыл бұрын
Only problem with pushing piston back is old oil going back up the line with crap in it better to undo bleeder nipple and push back and suck old brake fluid out of master cylinder and put new fluid through system
@AdmissionGaming
2 жыл бұрын
Why does triton do their brakes like this very old design new cars use disc brake.
Пікірлер: 69