Hi guys, (om642) after changing my timing chain through the right cylinder head ( feeding through) I am one link short or one extra teeth . At the start I thought it was the tensioner replace it was making too much noise and this please need the car to get around and work. thank you jack
@namphuong1036
2 жыл бұрын
a có hình ảnh sơ đồ cam cả đối trọng cho e xin với ạ
@Frank-i-e
2 жыл бұрын
Thank you for posting this, I have a question. On the other bank, would the intake side have the dot on the inside of the gear while the exhaust side be on the tooth of the gear or would it be identical to this side which the one holding the chain have the tooth on the gear lined up with the cylinder head casting en the outer exhaust one on the cam gear itself. Thank you
@kootenayeuroshop6602
2 жыл бұрын
I believe Identical but i would review my video again before commit. I'll look at it again.
@Frank-i-e
2 жыл бұрын
@@kootenayeuroshop6602 thank you so much
@Frank-i-e
Жыл бұрын
@@robby60259 yup, identical both sides. Balance shaft pointing at 12 o’clock.
@Frank-i-e
Жыл бұрын
Make sure your crank is set to the right position of course also.
@derekkchung
2 жыл бұрын
Hmmm, I am seeing 2 versions of crankshaft TDC for OM642. Yours has it at 12 oclock. The OM642 engine used on Sprinter has it at about 11 oclock. See v=I3fawLYopEY&t at 1:53. Both are OM642s so I believe crankshaft and all engine internal should be the same yet the timing is totally different? I am perplexed. Or maybe just 2 different crank pulleys and front timing covers.
@kootenayeuroshop6602
2 жыл бұрын
you are wrong. Om 642 do not have different top dead center locations
@derekkchung
2 жыл бұрын
@@kootenayeuroshop6602 what exactly is "different top dead center locations"? Cylinder 1 not at 12 oclock and combustion stroke about to take place? Do u know what I meant?
@johncrawford4465
3 жыл бұрын
Hi, is this the same with the other head...very useful info, cheers
@kootenayeuroshop6602
2 жыл бұрын
Yes, thanks
@coucouj2781
3 жыл бұрын
What stand and adapter do you use to put this engine on a stand ? Jeep 3.0 om642 here.
@kootenayeuroshop6602
2 жыл бұрын
standard engine stand. I modified my mounting adapter to make it work.
@elgroso806
10 ай бұрын
Im more confused than before ! 😂
@user-zb5gr6hm8z
2 жыл бұрын
Чувак где ты был раньше когда я мотор собирал ((( как мне нужна была эта имфа, иза этого по незнание немогли завести мотор(
@kootenayeuroshop6602
2 жыл бұрын
If you can say that in english I can reply. :)
@khadimloum2267
9 ай бұрын
Belle
@kootenayeuroshop6602
3 жыл бұрын
Just a standard engine stand
@alexchuchukov9032
3 жыл бұрын
With this engine, how many miles does the chain change?
@kootenayeuroshop6602
2 жыл бұрын
Depends on the oil used over it's life. Spec oil 229.51 or better the longer it lasts.
Пікірлер: 26