Being clumsy, the first thing I do is tape over the drain so I don't lose any of those little screws.
@daddysullivan87
11 ай бұрын
Step one cuss who originally put the cartridge in without grease, fight it for 30 minutes, install new cartridge WITH grease 👍
@NFTMule
4 ай бұрын
I just did this. I also had the pleasure of breaking it in half while stuck inside the body.
@lvond555
3 ай бұрын
@@NFTMule what do you do to get the stuck one out?
@tannerwest6823
Жыл бұрын
I take it you had good luck but as a plumber I recommend to never mess with the integral stops on the shower valve to turn the water off. Just shut off the main or at the street if you have access. Those Moen integral stops are notorious for the oring seal inside the stops to start dripping/leaking because they never get exercised(turned on/off) over time and the rubber seal gets brittle and rips. Just my experience with these but glad you had no issues with that. Just a tip to save you some headache for the next round
@GoShwkk
9 ай бұрын
What do u do if the cartridge thingy is completely stuck inside it dose not move at all The only way I was able to shut off the water was to burn the plastic piece with a torch so I can turn the knob to off but the thing won’t come out 🥲 it’s been 4 days and tbh I’m starting to smell
@p098098098
8 ай бұрын
@goshwk5848 Did you manage to get it out ?
@CashvilleUnderground
8 ай бұрын
@@GoShwkkreplace the entire shower mixing valve you dunce
@rocketrider1405
7 ай бұрын
I found when replacing my Riobel cartridge that the shutoff stops were a soft brass and just turning them made me nervous.
@lalocam80
6 ай бұрын
Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.
@bwlong
3 ай бұрын
Good video. I just replaced mine today. Easy and works so well. Didn’t realize the old carriage was so tight and old. New moen replacement turns with a pinky finger. I just turned my main water off in the garage. Other than that idiot proof. Thanks
@DaveDocDIY
3 ай бұрын
This is great to hear!! Love it!
@prayforthe_1644
Жыл бұрын
If u call Moen & tell them u are the original owner they will send u one free $aving $55
@narlycharley
11 ай бұрын
Usually they don’t even care that you’re the original owner.
@dj4080
5 ай бұрын
Everything worked the way you posted. Thank you.
@Zepherus14
5 ай бұрын
Thank you very much for this video! Really saved my bacon!
@Chris_dolmeth
Жыл бұрын
Lol that clip tho… don’t drop it behind the wall or you better hope you keep extras on your van lol
@jinghuidong1121
3 күн бұрын
You save my life
@synergy7501
Жыл бұрын
Thanks for video, alot of help.
@jrod3260
Жыл бұрын
Thank you Dave, keep Plumbing!! 👍😎👍
@DaveDocDIY
Жыл бұрын
Of course!!
@Justin232g
4 ай бұрын
Great video. Thanks this video saved me going through a crisis not knowing this was a replaceable part.
@myownstyleso.4987
19 күн бұрын
Just want to say ty, it wasn't this easy but this video still helped a lot.
@hugomenchaca912
5 ай бұрын
TY very helpful
@obedvalladares127
5 ай бұрын
Thank you so much the tips helped me a lot !!!
@jackanghoff8320
9 ай бұрын
I spent a month doing these before realizing you needed lubricant. I had to grip the hole with vice pliers so hard the brass got bent one time.
@smashninja22
5 ай бұрын
Will wd-40 be good enough?
@Bigbopperairguns
9 ай бұрын
Do not use pliers you will break it if it's been in there over 30 years use the tool that screws inside the Cartridge I love how they make it look so easy you could pull it out with pliers so you could just completely screw up your
@lizdarbey2053
4 ай бұрын
Thanks!
@MikeColburn
4 ай бұрын
I fought to get the pin in. What was going on? Why was it so difficult?
@koltonknighton1402
Ай бұрын
Nothing when it comes to plumbing is ever this easy. Just an FYI. 😂
@jcmgwhct2333
4 ай бұрын
Thank you compadre!👍
@markfischer2
10 ай бұрын
What do you do if it doesn't have that pin?? I have that sleeve but it doesn't move.
@JamesBond-bd3pz
6 ай бұрын
Excellent 👍
@chiliconholly
8 ай бұрын
What if you can't get the pin back in?
@parkerswafford1151
10 ай бұрын
Which do you like better moen or delta?
@roger101282
11 ай бұрын
Thank you help a lot. Struggling to find the link to get another replacement just in case
@chalinp4886
6 ай бұрын
My water keeps running even when I close it will this repair the problem. Edit thanks I fix it with this clip no more leak
@gabrieltorres1126
Жыл бұрын
My plumber use the wrong mixers, handle doesn’t fit. Can I swap that center piece for the right one? Both are Moen
@danwenner1906
Жыл бұрын
How come u tubers have the easy units? Mine was biotch to get out. Those side seals peeled back as I pulled the unit out..
@dweez4703
Жыл бұрын
Mine broke in half while pulling it out
@JoseRuiz1348
Жыл бұрын
When you reinstalled what do you mean by putting treatment?
@terrylunsford5085
Жыл бұрын
grease
@vegetablepolice1
Ай бұрын
1 valve showers have those to set hot and cold temp and pressure
@plomeria-hp
4 ай бұрын
Real , i 've been on that hook before, thanks.
@adamholbrook4408
7 ай бұрын
I replaced mine today, but now there is a slight leak coming out of the faucet whereas it didn't leak before. I had to replace it bc it wouldn't shut the water off in the tub. what's causing it to leak and how do I stop the leak?
@user-dj9rq3yb4f
8 ай бұрын
Hello. I changed this cartridge and now the water pressure is much lower, how can I increase it?
@MrColeStephen
Ай бұрын
Thank you!!!! Saved my ass!!!
@jaytemp5975
4 ай бұрын
What lubricant do I use and where do I put it?
@jess559vi
3 ай бұрын
What treatment do you add
@tonygucciano6875
6 ай бұрын
how do u tell what brand is in your house? I dont see any badging at all
@josephlinares96
Ай бұрын
What treatment?
@michaelpagnotta9101
23 күн бұрын
Does Moen supply the allen wrench? If not what size do you recommend? TIA
@dorkygirlsurvivalist3482
Жыл бұрын
Video helped me change mine. I messed up at first and it leaked worse. Turned out one of the rubber pieces fell off in the package. Been working on learning some basics for a small renovation in my current home and to build my own tiny house. Subscribed. Thank you.
@matthewgaul8197
10 ай бұрын
I changed that valve following this video, HC is up and now my hot and cold is backwards when showering. What did I do wrong
@xBuLLeTx1919
10 ай бұрын
Spin the stem only leave the cartridge installed and just spin the stem with no trim on only handle then test if still the same spin another half turn until right your welcome
@iliagoro3136
10 ай бұрын
Use 1 1/4 brush to clean out the inner shower valve after removing the cartridge. Otherwise you'll scratch the gaskets on the new cartridge and it'll leak in a day or two
@dirtyjimmydonitdirtymob8453
3 ай бұрын
Mine looks like that but how do I know if it’s that one
@Seven7Pain1
Жыл бұрын
if its a old one the make a tool so you dont pinch yourself with needle nose put on turn with channel locks take off pullout its cheap and usually comes with the new cartage wonder why his didnt
@fetarebel18
10 ай бұрын
Costumer : ok sir how much cost Plumber: just 700$
@artm5583
8 ай бұрын
Is it really??? That’s such an easy job.
@byindani
6 ай бұрын
What size Allen key? I have like 50 of them and they’re either too big or too small.
@dominiquewilliams6243
6 ай бұрын
Same thing with me it's not metric so it's got to be English
@byindani
5 ай бұрын
@@dominiquewilliams6243 gotta hammer in the T15 and twist!
@byindani
5 ай бұрын
Twist and hammer hard unless you’re willing to drill out the bolt, and spend an extra 165 replacing the handle.
@Donerightcarpentry
Жыл бұрын
Do any of you guys know whats the typical labor charge to replace a shower cartridge?
@rockridgefarms
Жыл бұрын
Depending where you are....average hourly rate is around 100$
@vincemoreno7932
3 ай бұрын
What treatment did you put on?
@kennydabossyo6198
Ай бұрын
A certain type of grease. It helps sliding it in and prevents hard removal next time and when showering the handle gets extra smooth....all because of the grease
@kennydabossyo6198
Ай бұрын
Also, helps not mess up those o rings and rubber seals
@SteveAdlard
2 ай бұрын
Stuff a rag in the wall so clip won’t disappear when you drop it,like I’ve done
@datboyv1980
10 ай бұрын
Would this fix a low pressure issue?
@DaveDocDIY
10 ай бұрын
I’ve seen it fix it for Moen
@AM-un4rh
8 ай бұрын
Why do we need to change this?
@jeffreytholm9669
2 ай бұрын
These jobs can backfire on you quickly. Cartridges are plumbers scariest jobs imho.
@kenestra123
9 ай бұрын
Why dont you go a little faster so you can really piss people off! LOL!
@chrischsproductscom1636
7 ай бұрын
Thank you
@mycaddigo
8 ай бұрын
Lesson is, buy a delta valve instead …
@mirelurkhomevideos
5 ай бұрын
have fun when the bonnet nut gets stuck and you have to rip the whole value out
@brettwagner-sr4yu
5 ай бұрын
The only Moen stuff worth a damn is CFG stuff. Their sink stems are so easy to work on. No seat or spring. Just stem and the nut.
@josesoberanis681
20 күн бұрын
👍 👍 👍 👍
@PISSDIVV
Жыл бұрын
How much did you charge them?
@monsterp.g.1741
Жыл бұрын
$299
@MichelleAv-oq7jp
4 ай бұрын
What if you have 22 years of corrosion on and it wont come out
@ryantracey8574
Жыл бұрын
I just did this but my off is when the handle is up and I only get hot water in the 5 o'clock position, I've double checked and my "HC" is on the top, and my handl moves and stops on the right places, the old one was too dirty and I didnt pay attention, I'm thinking my copper housing/pipes must be ran wrong so I'm gonna try and flip the cartridge upside down unless someone knows something I don't
@DaveDocDIY
Жыл бұрын
I’ve seen that happen. Does there happen to be another tub or shower on the other side of the wall? I’ve seen guys tee the pipe and go right over. 😑
@ryantracey8574
Жыл бұрын
@@DaveDocDIY no but there is one directly above it
@xBuLLeTx1919
10 ай бұрын
Then remove the handle and black plastic piece and turn the black and handle facing down
@walterham5107
Ай бұрын
Bueno!
@eduardobetancourt4347
3 ай бұрын
Very rare that that type of cartridge comes out complete, you usually have to take out in pieces 😢
@Fengshawn86
4 ай бұрын
What can we do if the old cartridge is not pulling out? Pin is out and cartridge won’t budge. Won’t even turn 45° like the instructions say.
@JAMESPTOOLE
4 ай бұрын
They make a pulling tool.
@Fengshawn86
4 ай бұрын
I did get the tool, it was still so stuck I had my foot up on the wall and was using all of my body and twisting. Thought I was gonna break a pipe. The rubber was coming lose and I was fighting and ripping at the rubber until it came all the way out… it was rough.
@squirtmann17
10 ай бұрын
why tf this video so fast
@davidtesso4789
9 ай бұрын
Bro I've had to chisel those valves out of the housing cuse they broke apart. They sure ain't DELTA
@studmuffin2330
Жыл бұрын
My cold water barely trickles but hot comes out fine. I replaced the cartridge. Any ideas?
@Ricky-tl8bz
Жыл бұрын
Check your water shutoff valves. Make sure the cold is open all the way.
@studmuffin2330
Жыл бұрын
@@Ricky-tl8bz I didn’t know a shut off valve but I will double check. Thank you
@Ricky-tl8bz
Жыл бұрын
@@studmuffin2330 Yeah, my house has individual shit off valves in the basement for each sink, bathtub, toilet. This is so I don’t have to shut off the water to the house. Just for what I need to work on.
@rockyravine1155
11 ай бұрын
you most likely have a valve like this video with water stops left and right of the cartridge. Take the cold stop out and run the water quickly and back off. Most likely this will flush out around the stops and you'll be good.
@dannysmith6093
Жыл бұрын
This is why I only install delta shower valves. So much easier
@xBuLLeTx1919
10 ай бұрын
Ya the stops suck most 1222s will not come out with needle nose pliers sometimes u will need to screw screws I. The cartridge to pull it out if your puller don’t work ha and the h/c don’t mean shit when the stem has been turned around by whoever the hell touches it before you and ps don’t ever buy knock off 1222s to save u 20$ it will bite you in the ass on install day love moen
@Chosenfew_0129
4 ай бұрын
I broke the screw
@stinner44
2 ай бұрын
I see nobody cleans the inside to remove hard water deposits
@dongoldo88
10 ай бұрын
Lucky that stem didn’t break he would of been pissed !
@maryford4667
2 ай бұрын
It's not that easy for some people also you need a good bit of power to pull it out if it's been years and putting it back in I'm 21 male 240 and it was hard to get it back in not fun to deal with the lub it come with use all of it
@stress.relief
10 ай бұрын
Help! i dropped it in the wall
@_RYEN_
Жыл бұрын
I’ve changed hundreds of these in apartment complexes seem like they are made to last a year or two
@HarminderSingh-jc7rf
Жыл бұрын
What you charge for that
@HateDietPepsi
Жыл бұрын
I need to replace mine about every 5 years within my house. Doesn't matter whether it is heavily used shower or not.
@_RYEN_
Жыл бұрын
@@HarminderSingh-jc7rf it really depends if I’m supplying the part or not. If they have all the parts and I’m just doing the labor and it’s a pretty easy removal, I’ll charge about 100 125 bucks.. I typically try to make about 100 bucks an hour. If I’m doing is that and I’m going over there specifically for that if nothing else I’ll probably charge 150. 200 bucks with parts.
@_RYEN_
Жыл бұрын
@@HateDietPepsi no it doesn’t because water is still behind the vaule. You should get a lot longer use out of one if you don’t use the shower as much, of course, but they still will go bad, especially if they’re just sitting there, not being used kind of a double edge sword.
@Inmate533
11 ай бұрын
That's some filthy water you got there son. Mine last about 8 years and I have high levels of iron and manganese, which are the worst for clogging these things up.
@ricksanchez6411
11 ай бұрын
No caulking
@DaveDocDIY
11 ай бұрын
No need. Face plate seal fully covers the valve opening.
@JUDGEME5150
24 күн бұрын
HOW DO U KNOW ITS THE 22….!!! Be clear in your vids!!!
@keithmccormack6248
4 ай бұрын
Too back it’s not actually this simple.
@serdgeedgerunner
8 ай бұрын
you barely show most interesting part. I can't remove my cartridge from the pipe, it stuck..
@kylecraanen6254
Жыл бұрын
I have a metal plate behind my handle instead of the plastic how do I get this off?
@brandonburnett6792
Жыл бұрын
I dropped mine in the wall 😅
@DaveDocDIY
Жыл бұрын
That’s a lesson/mistake I learned once and ONLY once. Best way to learn though! 😂
Пікірлер: 126