Thank you sir. Well done. You explained that so simply I didn't even have to look at the screen to understand what you was saying.
@pmtips4482
3 жыл бұрын
You are very welcome
@davidr6585
3 жыл бұрын
And thank you kindly for providin' what I needed to watch ;) I'm wanting to change over to a keyless chuck on my Ryobi DP120 and I'm pretty sure it's an MT2 but now I know how to verify!
@pmtips4482
3 жыл бұрын
Thank you for watching! Have a good one!
@crackedfingerz
2 жыл бұрын
Very clear and to the point. Good stuff. Thank you very much.
@pmtips4482
2 жыл бұрын
You're welcome!
@bigmotter001
2 жыл бұрын
Great video! Very clear and educational. Thanks for sharing and take care!
@pmtips4482
2 жыл бұрын
Glad it was helpful!
@starhawke380
7 ай бұрын
I have that same drill press, The chuck usually just falls out if I look at it funny. Never had to use the tool to remove it. Wen said that was normal when I asked for a new one.
@pmtips4482
6 ай бұрын
Thanks for sharing!
@douglasbattjes3991
2 жыл бұрын
Thanks so much for the video, you have on on the differences between R-8 & MT 's guess I can look on other videos here,, Very well don'e on the explanation.
@pmtips4482
2 жыл бұрын
Thank you for watching and commenting! I really appreciate it!
@gottmituns1938
2 жыл бұрын
This was helpful. How well did annular cutters work with this drill press?
@pmtips4482
2 жыл бұрын
I have not tried angular cutters yet, but see no reason they wouldn't work. Thanks for watching!
@Dr.Scorpio
2 жыл бұрын
Thanks for the great video
@pmtips4482
2 жыл бұрын
Glad you enjoyed it!
@clementfortin4315
Жыл бұрын
Hello sir thanks you for your nice video. Im new to this i just bought a lathe and now i want to buy a live center and a chuck for the tailstock. So now im trying to understand what is a morse taper and what other type they are and how it works. Some help would be greatly appreciated thanks.
@pmtips4482
Жыл бұрын
Clement, I don't have the knowledge to help you on that. I go by what the owners manual specs on the tool in question. In a nutshell, the industry tries to standardize things like tapers, and chucks, etc., but then a new product comes along all while there are a few million of the older tools with these tapers, stocks, and chucks. All with different sizes based on the power required to turn the machinery. Thanks and good luck!
@pmtips4482
Жыл бұрын
Clement, if possible consult your owners manual on the tool in question. You can also Google morse taper as there is lots of info on that. I just don't have the knowledge to discuss. Thanks and good luck!
@bobmurchie9908
2 жыл бұрын
Very helpful, thanks!
@pmtips4482
2 жыл бұрын
Glad it was helpful!
@aryonugroho8711
5 ай бұрын
I dont understand inch, do you have explanation in metric? Thank you
@pmtips4482
5 ай бұрын
An inch is 25.4 millimeters. You can do the fast conversions on any search engine like google. Thanks for watching!
@jeremykemp3782
2 жыл бұрын
do you get different size openings for the actual drill bits for a no 3 taper? Or do they all open up to the same size?
@pmtips4482
2 жыл бұрын
I'm not sure on that. The drill bits I have are specific MT2 taper and it is stated on the storage tube they came in. Thanks for watching!
@christophersimpson7052
4 жыл бұрын
3 hands try use the quill lock it saves you the wrath of the handle on your kuckles 👍
@pmtips4482
4 жыл бұрын
I don't think this model has a quill lock. After reading your comment I looked through the owners manual again and nothing is mentioned about it.
@robmerrell1745
3 жыл бұрын
@@pmtips4482 Even the cheap ones have a quill lock, even though they don't know it. It's totally useless for most things where you'd like to lock the quill, but for this one thing it's useful. Just pull it down and tighten the nuts on the spring on the other side of the press. Also, great info about figuring out which MT size you have. Thanks.
@eddiepenn5643
4 жыл бұрын
Very helpful Thanks
@pmtips4482
4 жыл бұрын
Glad it was helpful!
@falkenvir
2 жыл бұрын
anyone ever having a drill chuck dropped on their thumb?
Пікірлер: 33