One year I replaced with ceramic bearing last 3 year's. It depends on how and where we drive . I never drive on wet conditions snow mud ect.
@jaybailey4394
9 ай бұрын
Yes sir. Right around 2 years. Mine just did the same thing. I was going to pick up the rebuild kit this week, but I think I need to take another look at the end of the rotor. Thanks for the video.
@rodneylyn1604
4 ай бұрын
I've had some success repairing the rotor windings by removing and wrapping the rotor with Kevlar string with a fine coat if epoxy on string. Then replace those sloppy bearings. Its not 100% perfect, but if you can use a balancer of somekind might be pretty damn close . Trial and error!
@toothco
Жыл бұрын
Gool rc brushless bearings started making noise after one of many wet and dirty bash sessions. Caught it before motor was damaged. Lasted a year of heavy use.
@rcaction7428
Жыл бұрын
Yea that’s pretty good, they all wear out, better off changing them before they go bad,
@babissj4
2 ай бұрын
Just happened today with my erevo 2 motor , after a few full throttle straights the motor kinda stuck just like yours lasted 4 years.
@benjaminbarmore805
5 ай бұрын
Literally same thing happened to me on my THIRD RUN with my brand new e revo 2.0…. 2200kv motor shot just like that. $110 out the window. Gonna hear it down bc when I went to look at it after run it was extremely hot and smelled horrible.
@goneviral6037
5 ай бұрын
It should be under warranty.
@CSL33
5 ай бұрын
@@goneviral6037 Not if it overheated due to over-gearing it though....
@babissj4
2 ай бұрын
Just broke mine. overheating the motor and it's done for
@JevoUK
2 жыл бұрын
The bearings went in our Traxxas motor at the bottom the can leaving the outer bearing casing stuck in there, we could not get it out. Eventually we drilled through the bottom end of the can and pushed out the bearing case, my plan now is to use two sets of bearings to hold in the other. I’ll have to do a video of it, it might be interesting to see what happens. It will be over on our rc channel called RC Havoc UK.
@rcaction7428
2 жыл бұрын
Sounds interesting, I would think it would work, great idea too! Those bearings really get stuck in there!!
@ClumsyToast
9 ай бұрын
Thumbs up for the cat
@TheRedComet1821
Жыл бұрын
Had this happen to my XRT after 2 months.
@zoologer
3 ай бұрын
Same here. XRT and X-Maxx motors are so fragile, that you can't even make this bearings replacement on time. Now I have 3rd motor (since January 2024) and yesterday hybrid ceramic bearings arrived - will replace stock ones and see if it helps this ridiculously short motor life.
@perry5526
Жыл бұрын
Ty by seeing your vid helps
@faststongesdrc7075
3 жыл бұрын
I have 3 udr and im killing mine only after 2 or months with out maintenance. ...damn cats
@rcaction7428
3 жыл бұрын
That is crazy! I just got my udr so I’ll have to how long it will last. Does the bearing go bad or what happens?
@faststongesdrc7075
3 жыл бұрын
@@rcaction7428 im not saying they all brake but yes if no maintenance is done, it will brake fast, spacially if it gets water. You must seal the rear motor at first. The rear bearing is expose and take a lots off dust and when i will fail, it will get desalign and the magnet will rubb against the can and its over. Since I put a small piece of tape on the motor to seal the bearing, and maintenace everry few months, no problem at all since then.
@@faststongesdrc7075 that’s a great idea sealing it, I wonder if hot glue or silicone would work also?
@faststongesdrc7075
3 жыл бұрын
@@rcaction7428 hot glue will jam the bearing and grease or any lube will atract dust and its gona be just worst.
@ponyexpressrc
2 жыл бұрын
Happened to my motor just recently, lost a couple of screws holding the rear cap in place and it must have misaligned the rotor, rotor looks just like yours. I did try to epoxy the magnets in place which seem to work to a certain rpm but its basically the a smoke machine now 😂
@rcaction7428
2 жыл бұрын
Yeah using epoxy is a great idea but I bet you that’s the part that smoking too I should try Epoxy
@ponyexpressrc
2 жыл бұрын
@@rcaction7428 yes could be the epoxy smoking but not trusting it one bit as i fear it might burst into flames. Best i get a new motor and learn from my mistakes 💸💸
@jdpasltrains
3 жыл бұрын
Traxxas wants you to buy a new motor. No maintenance. lol
@rcaction7428
3 жыл бұрын
That’s so true!
@clinthipfner6042
Жыл бұрын
I would say like under 30hrs got it at the end of the last summer i bet iver only took it out 10 or 15 times if that, but its not as bad as your just a bit frayed the front bearing went just like yours trying my hardest to get the bearing sleeve out to no avail its like 150 in canada for a new motor ffs
@brianu33
Жыл бұрын
My Arrma 3s bearing exploded in motor. The armature and inside can in packed with dirt. Should I spray contact cleaner inside and on armature to clean it? Is that safe? I’ve read I should block unused motor holes etc to stop dirt.
@shonen881
Жыл бұрын
Can the bearing be replaced with ceramic bearing
@OtherSide..
Жыл бұрын
I think that might be Teflon coating
@clinthipfner6042
Жыл бұрын
Its kevlar thread. And a heat resistant epoxy. I'm actually fixing mine. Once I get the stuff. My bearing went like his but it's not as bad my thread is frayed and dirty tho in the front. Going to re wrap the front and run it till she's done
@nathansayer8066
Жыл бұрын
What tape are u using to re wrap
@nathansayer8066
Жыл бұрын
@@clinthipfner6042what tape are u using to re wrap
@khaiselhassadi5361
Жыл бұрын
2yrs. Arrma typhon 3s
@BackyardBashers1275
7 ай бұрын
My xmaxx exact thing, 5-10 runs tho 😠
@goneviral6037
7 ай бұрын
wow, thats horrible!! was it really hot out? or something extreme ?
@BackyardBashers1275
7 ай бұрын
@@goneviral6037 nope, middle of fall, replaced it and now I’m replacing bearings every year 🤣🤣
@rcaction7428
7 ай бұрын
crazy, did it get really hot?
@BackyardBashers1275
7 ай бұрын
@@rcaction7428 it did because I drove it back to the truck after which is probably where it killed the rotor
@BackyardBashers1275
7 ай бұрын
I think it is the little balls from the bearing that cut the Kevlar wrap
@perry5526
Жыл бұрын
Mines not that bad
@perry5526
Жыл бұрын
Ty 4 your vid
@perry5526
Жыл бұрын
Ty 4 your vid now how do u get the rear bearing out the bearings gone with the the piece up against the wall still in there
Пікірлер: 45