sir where is video of winder and unwinder drive reference.. this video was informative.... nice work sir.
@nageshpandey5333
3 жыл бұрын
thanks sir after long time very useful video
@sivasubramanian5461
3 жыл бұрын
Use full video sir.
@Lopanfernando
3 жыл бұрын
Very well explained sir..thanks
@lifetenbo7375
3 жыл бұрын
Very very nice and useful video nice
@dhiraj-shukla
3 жыл бұрын
After long time. Thank you sir..
@Zeeshankhan-qn5yv
2 жыл бұрын
🙏 thanks a lot sir, for giving information.
@WNAZ-WALA
6 ай бұрын
Thanks for
@avinashamberkar3780
3 жыл бұрын
Waiting for next video
@dipankardeo8479
5 ай бұрын
Sir make vodeo to calculate MPM .. DEFLECTOR ROLL ENCODER
@Lopanfernando
3 жыл бұрын
Sir please make a video on ABB dcs 800 dc drive commissioning or explain it's important parameters
@himanshusharma5345
3 жыл бұрын
Sir ek video optocoupler pe bhi bnaya plz
@heroestec534
3 жыл бұрын
Please explain DIRECT TORQUE CONTROL PRINCIPLE OF ABB DRIVE.
@saurabhmishra4953
3 жыл бұрын
Apse request hai ki kuch electrical questions ki video b bnaye hai jo ki common ho.. interviewer puchta ho.
@priyadarsanbarad1090
3 жыл бұрын
sir i am one of ur subscirbers.could u please upload a video about torque reference and how to commission by using drive parameter.ex. winder and unwinder.thank u sir.
@lifetenbo7375
3 жыл бұрын
I like to you learning
@rajeshkmaurya05
3 жыл бұрын
Please make tutorial abb dcs500 dc drive parameters settings
@aforautomation
3 жыл бұрын
This model is obseleted and replaced by DCS800.i will try to make video.thanks for watching
@mayurI4188
3 жыл бұрын
Sir ko time mila
@aforautomation
3 жыл бұрын
😀
@nageshpandey5333
3 жыл бұрын
sir ismein LCW ka use nii hota hai kya sirf counts ko alag se plc drive ko send karta hai?
@aforautomation
3 жыл бұрын
LCW is only for start stop enable etc not for speed reference.speed reference is transmitted with separate data word.
@nageshpandey5333
3 жыл бұрын
Thanks sir
@nageshpandey5333
3 жыл бұрын
sir motor k rated RPM/HZ k kitne upper tak motor ko chala sakte hai?
@aforautomation
3 жыл бұрын
upto 100 hz but torque will be Derated.speed more than nameplate should be avoided for long time.as igbt temperature increases.
@vorapobautomation9760
Жыл бұрын
Please explain DIRECT TORQUE CONTROL PRINCIPLE OF G120 DRIVE.
@mohammadbilal8708
3 жыл бұрын
Sir next video kab tak aey gi
@vorapobautomation9760
Жыл бұрын
How to calculate from RPM to MPM. ?
@sudiproyroy051
3 жыл бұрын
Is this rewinding application. And VFD is speed mode or torque mode.
@aforautomation
3 жыл бұрын
Yes you are right Sudip its rewinding application and drive is in torque control mode.
@sudiproyroy051
3 жыл бұрын
@@aforautomation in this application the dia of a roller is increasing continuously. And VFD speed ref. will decrease continuously. You are not considering the increasing dia. of roller for ref. calculation.
@sudiproyroy051
3 жыл бұрын
@@aforautomation how I calculate the torque ref.
@nageshpandey5333
3 жыл бұрын
Next video kab aayega?
@aforautomation
3 жыл бұрын
very soon.thanks Nagesh for your interest.
@nageshpandey5333
3 жыл бұрын
Sir pleases let me know how I can contact you.
@aforautomation
3 жыл бұрын
mail me on aforautomations@gmail.com or contact me on linkedin
@nageshpandey5333
3 жыл бұрын
@@aforautomation ok sir
@gauravsharma-jq8jb
3 жыл бұрын
Sir will you please make video on Auto Gauge controller in cold rolling steel plant
Пікірлер: 40