Do NOT, keep the zip ties on the inner tubes for extended periods of time. They will scratch the tubes and will cause leaks. They do sell kits specific to this zip tie trick, but if you dont want to undo the suspension, do the zip tie trick, keep those forks clean, and remove them after getting you suspension set up.
@Motogents
2 жыл бұрын
Yeap i you are totally right , i forget to include this in video. I am gona pin this comment for everybody to see. 👊🏼✊🏼💨
@BarnettSpeedSuzukiThou
Жыл бұрын
@@Motogents not really because it rarely moves
@patrickspapens5497
11 ай бұрын
I have worked on suspension forks for Husqvarna, KTM and Ducati. All of them get thermal spray coated with tungsten carbide. A zip tie will not scratch the surface as tungsten carbide is extremely hard. Even sand could damage them if they weren't treated. But always check if your forks are treated and hard enough to not get scratched by plastic
@banushankar566
Жыл бұрын
Thanks dude, its 4.46AM, I was trying to find this video from last night 9pm, ll keep you posted on the progress
@gvybin
Жыл бұрын
Hi, Be carefull to not misinterprete this method. You have to take into account the specs of the bike. There are bikes out there , where the suspension bottoms out way before the end of the chromed forktube. f.e. My Triumph Tiger sport has a total front wheel travel of 140mm according to specs. From top , If I raise the front of the bike above the ground , I measure 170mm of chromed tube. SO.... My front suspension bottoms out 30mm above the bottom of the chromed forktube. In my case, the cable tie should not come lower then around 45mm above the bottom of the chromed forktube. Long story short : bottoming out is not always hitting the end of the chromed tube. Often it is higher up and you need to know/measure that point, using the specs of your suspension
@patrickspapens5497
11 ай бұрын
'dark magic' 😂 it may seem so in the beginning. Good to see Dave Moss in the video, I learned how to read my tire wear and adjust my suspension for track use watching his videos and tuning guides. Omce you know how a suspension works, whether it's the fron or the rear, you can adjust them relatively easily. Servicing them is another story but nasic understanding of how they work and how to maintain them helps a lot!
@Vijaykumar-cw6pz
2 жыл бұрын
Thx bruh for an simple hack, It's really helpful 😊🔥
@Motogents
2 жыл бұрын
I am so glad to hear that 👊🏼
@BehzadBhandari85
10 ай бұрын
Thank u...for explaining so simply
@Motogents
10 ай бұрын
You are welcome mate 👊✌️
@rambofan1
2 жыл бұрын
Good ups on you givin Dave moss props he’s a legend
@Motogents
2 жыл бұрын
I said it once and i will say it again,that guy can talk with motorcycles ,that man is a bike guru 🤣
@rambofan1
2 жыл бұрын
@@Motogents fr
@BehzadBhandari85
10 ай бұрын
Thank u for simplifying this ..I will try it...u explained it in a way laymen can understand..
@Motogents
10 ай бұрын
Try it is very simple od i monkey like me can do it you can do it too 😭
@Motogents
10 ай бұрын
What bike do you ride ?
@OmkarPatil-qd7rj
3 жыл бұрын
Big fan bro
@SvenTviking
Жыл бұрын
Icm from the bottom on “upside down” forks. Traditional forks it’s 1cm from the top.
@Motogents
Жыл бұрын
Yes that make sense 👊🏼
@Jandejongjong
2 жыл бұрын
Perfect
@Motogents
2 жыл бұрын
👊🏼✊🏼💨
@hiphoplover87
Жыл бұрын
will it work for every motorbikes??
@Motogents
Жыл бұрын
Yeap it will work on every bike 👊🏼✊🏼💨
@OmkarPatil-qd7rj
3 жыл бұрын
Plz make video of oil change and air filter change
@Motogents
3 жыл бұрын
It is on the list 3000km more and i will do maintenance video,oil filter,oil , andair filter. ✊👊
@OmkarPatil-qd7rj
3 жыл бұрын
@@Motogents ❤️
@ZygmuntKletterstein
3 жыл бұрын
Where should the zip tie be at the beginning please?
@Motogents
3 жыл бұрын
When you put ziptie on leg fork pull it all the way up almost to the fork seal.
@ZygmuntKletterstein
2 жыл бұрын
@@Motogents Thanks!
@Motogents
2 жыл бұрын
You are welcome mate 👊🏼✊🏼💨
@Jandejongjong
2 жыл бұрын
If you don’t want to add zipptie you can also use a permanent marker! Thank me later!
@g3ges3
2 күн бұрын
And how exactly will that move Einstein?
@OmkarPatil-qd7rj
3 жыл бұрын
Hii bro please make more videos plz
@Motogents
3 жыл бұрын
Tnx man that means a lot,more great content is coming.
@johnnyappleseedz422
Жыл бұрын
To confirm, 1 CM (10mm) correct?
@Motogents
Жыл бұрын
Yeap thats right 👊
@AmmarKhan-nd3xo
8 ай бұрын
Is it too hard if suspension is not bottoming out
@Motogents
8 ай бұрын
IT all depends on where your zip tie is ending.
@Heiwido
Жыл бұрын
Using a permanent marker would also do the job
@Motogents
Жыл бұрын
Yeap that could work too 💪
@johnnyappleseedz422
Жыл бұрын
Can you elaborate on using a permanent marker? Do you just draw a straight line down the fork and identify what gets rubbed off and what remains? How does that work?
Пікірлер: 43