Thank you, for telling me the wrist pin clips are in a red bag. I thought it was trash. Had to dig through my trash. All is good now!
@gotchurebeacons-gaming9023
2 жыл бұрын
Great video! Here’s a few things to add. The G clip is designed to be installed one way. The tine you grabbed with the needle-nose pliers sits proud of the coil, be sure that side is facing outward. Also, it’s best to have that tine pointing downward for the clip’s resting position. Also, before installing the jug, I’ll lay a sheet of wet fine grit (1500) on a flat surface and lightly “circle sand” the mating surface for the top of the jug, this will help polish away any micro-imperfections. Ride safe!
@patrickharding4831
2 жыл бұрын
Good video mate, done well, here's a tip for the gudgeon pin clips, put one of them in the piston before putting the pin in, then you only have to do the other clip whilst in the awkward position with the piston installed, and don't tighten the main studs any tighter than finger tight because when the head nuts are torqued it applies too much pressure at the bottom of the drilling where the studs bottom out and make contact, it can cause the engine case to crack during thermal cycles. Keep it up, really dig your content. Cheers
@rgbigdog
2 жыл бұрын
Note to self, put in one wrist pin clip into piston before attaching it onto the connecting rod. This will help greatly when assembling the piston to the connecting rod.
@worscohli
4 ай бұрын
Why only one?
@rgbigdog
4 ай бұрын
@@worscohli if one isn't obvious I don't know what to tell you.
@bryceevans8340
Жыл бұрын
Bruhhh this was a fucking amazing video good detail and quality very informative too 👏
@keeganhache6667
2 жыл бұрын
Please upload more your videos And la hovers are the best for motorized bikes.
@MotoredLife
2 жыл бұрын
Will do! Whole bike assembly is next
@davidonzahwah3777
2 жыл бұрын
Man this bike game is goin crazy out here!
@rogerboswell5483
Жыл бұрын
I have to fix my engine now i know how.. thanks 😊
@edgufler1122
2 жыл бұрын
Happy New Year Alex. Happy to see you back with a great video.
@tonytaylor5087
2 жыл бұрын
Good to see you man!
@mrmiracle9956
Жыл бұрын
Thanks😊
@mathewsphiri-qd1db
Жыл бұрын
I like your shop
@shaggysidbacon6144
2 жыл бұрын
Love this dude's energy and knowledgeable input I'm subscribed to bikkerberry.. but I'm going to subscribe to this channel ..thanks for this vid keep up the great work
@MotoredLife
2 жыл бұрын
Thanks for watching buddy!
@lorilouden6799
Жыл бұрын
@@MotoredLife hey man , I appreciate the video , I’m a new builder , on my second build , first one was a engine from bike berry , this one I’m doing now is a pk 80 wildcat , anyway question is what can I do to get the head studs seated in further , I put blue Loctite on them because I heard that was good to do , and I started turning them in and they went about halfway down before the wouldn’t go down any further , I even tried vice grips to get them seated in further , to no avail. I can’t properly torque my head because of this and it leaves a little gap between gasket and cylinder. How can I get these studs seated in further? I appreciate any feedback
@bryduhbikeguy
2 жыл бұрын
Holy mackerel.2nd comment?Glad to see you back.
@Westhelockpicker
Жыл бұрын
If the engine is off the bike you can put the piston in the cylinder and then put it down the studs and put the bar thru the rod and piston. I've seen people do it both ways
@bryduhbikeguy
2 жыл бұрын
Have you seen an 80cc kit with a 1 piece cylinder/head,that bolts on at the Base,and not with studs like what you just built?I bought 1 online.I'd like to know what you think of them,or tips from everyone about it.Thanks.
@JorgeRodriguez-ei2gi
2 жыл бұрын
Great explanation Mr Alex,very good keep sharing with us your built & upgrades & motorized bike wey learn a Lot ,Say hello Joe & Bros ,suscribes thanks.
@shaggysidbacon6144
2 жыл бұрын
Just finished building mine...it's on a Kent seachange
@kaoskustomgarage1741
2 жыл бұрын
Venoms looking good 😉
@rgbigdog
2 жыл бұрын
You can us a worm-gear hose clamp to squeeze the rings.
@daddiegreensDad190
4 ай бұрын
There's two washers that are in the box for bearings and pin what about those
@jonathanlincolnthefamouszi2137
Жыл бұрын
Hay what's that thing called that holds the engine while you are working on it
@JMB676
2 жыл бұрын
Hey bud glad to see you posting again, I didn’t get a notification but I stopped by just to see wheee you have been. Not sure y not getting notifications I have it all turned on but at least I seen your here. Hope all is well bud, hope your well and hope you stop by my channel too. If you do please leave me a comment letting me know what you think of the content. Thanks for sharing brother.
@peterjohn3180
7 ай бұрын
Can you help me? I've bought a cylinder kit for a motorised bicycle engine but the stud spacing is 50mm and all my cases have 45mm spacing. Any ideas?
@kleptoklepto2560
11 ай бұрын
hey bruva! ive got the "TDR 100CC MOTOR! im thinking a bit more speed! what do i need to do with the piston n top end to spruce her up?
@lucianlucian1116
2 жыл бұрын
I could mount an 80 cc cylinder and piston on a 100 cc engine because in Romania there are no 100 cylinder and pistons, I want to point out that it fits in holes only that the 100 cc cylinder and piston is 50 mm and the 80 cc has 47mm?
@raulcruz6601
2 жыл бұрын
EXCELLENT
@dustinh4175
2 жыл бұрын
Im not sure if its a good idea or not but i packed a little grease into to piston clips to try and keep them seated. Bout a tank of gas threw it so far so good.
@topdog3407
9 ай бұрын
did it work fine?
@thecbc7658
Жыл бұрын
What socket size do I need for the acorn nuts (head)?
@thecottsdalesegment9141
2 жыл бұрын
Was riding yesterday, bike (phatmoto all terrain) died and would start back up. Cleaned the clutch couple days ago, may have got some oil on the clutch but don't believe inside... any suggestions?
@Drago_fire2164
2 жыл бұрын
Can anyone drop a link to a windowed piston for the bt-80 electric start motor? I can't find any measurements online and I don't have the tools to measure. Thank you
@worscohli
4 ай бұрын
I can already tell the wrist clip is going to be the most annoying part during this build... honestly it seems like some of these things couldve already been assembled... im going to do it. but i just hate how they make engines rely on Small Ass Pins for whatever reason...
@damarcuschaney503
2 жыл бұрын
What size are the cylinder head studs?
@upsidedown1986
2 жыл бұрын
Is there a top and bottom ring, or are they both the same?
@MotoredLife
2 жыл бұрын
Both are the same! Good question
@isasauseda5889
2 жыл бұрын
Happy holidays
@larryshaver3568
2 жыл бұрын
doesn't the wrist pin have a bushing? i didn't see one
@MotoredLife
2 жыл бұрын
Nope just bearings
@kimdecastro9156
2 жыл бұрын
great video alex .question I notice the head has two gaskets on the bottom .if you took away one gasket will it change performance or no difference at all. first time builder.
@Jon.Carlsen
2 жыл бұрын
Normally there is one gasket. I'm wondering why Alex used two as well. Adding a gasket raises the cylinder height creating a slight drop in compression.
@billpfann332
2 жыл бұрын
I have a question after about 7000 hard mileage I'm rebuilding my motor.while taking the boost bottle off the frame I noticed the boost bottle was completely full of fuel.Is this normal.I ride hard and wide open all the time.
@MotoredLife
2 жыл бұрын
Boost bottles are nothing but problems. Imagine trying to tune with all that fuel pouring into the carburetor at random times!
@billpfann332
2 жыл бұрын
@@MotoredLife it seemed to help the motor idle better, next question.In your opition whitch is better a brass head gasket or copper?.again I ride my bike hard wide open.
@keeganhache6667
2 жыл бұрын
@@billpfann332 if you run a two stroke wide open all the time you will destroy the piston and cylinder lining
@billpfann332
2 жыл бұрын
@@keeganhache6667 yes I know this, I r in a rich oil mixer, and ad a Teflon additive.keeping motor cool help the life also.
@themadasshatter1088
13 күн бұрын
You can't over-lubricate.
@BuildBreakFix
2 жыл бұрын
Wow back from the grave again! Lol
@fernandocastillo8026
2 жыл бұрын
My cylinder doesn’t want to slide down I’ve tried so many times and I’m not sure why it’s really annoying
@MotoredLife
2 жыл бұрын
Ur rings are not in maybe?
@fernandocastillo8026
2 жыл бұрын
@@MotoredLife They are I did it how you did it in the video and I don’t know what’s wrong I’ve been trying to slide it down for 2 days I stops sliding when it reaches like the gaskets
@MotoredLife
2 жыл бұрын
@@fernandocastillo8026 the gaskets?
@fernandocastillo8026
2 жыл бұрын
@@MotoredLife yea it’s one side that looks like it doesn’t go in, is there any place I can send pictures to and you could help me out? I’ve been trying to fix this for 2 days
@MotoredLife
2 жыл бұрын
@@fernandocastillo8026 for sure! MotoredLife@gmail.com
@joshcolbert4682
2 жыл бұрын
can you uh upload more often?... ...
@MotoredLife
2 жыл бұрын
Omg thanks so much for saying this! i needed a good kick in the right direction! You know what just because you asked I'm going to post a new video soon
@joshcolbert4682
2 жыл бұрын
@@MotoredLife haha thanks i really enjoy your content. quick question do you think the laws would change if more knuckle heads get these bikes?
@MotoredLife
2 жыл бұрын
@@joshcolbert4682 I think they would change for the worst honestly 😬 I've seen people do some dumb things on these bikes and get hit and get hurt
@joshcolbert4682
2 жыл бұрын
@@MotoredLife i agree, im in a small town and i think my plan is too not make my bike look so cool or appealing so not just anybody would get one cause i think if a lot of people did then the cops would be all over our ass hahahso like maybe i might sand my gas tank and paint it pink or somthing not so flashy, just trying to make it seem like the bikes arent as cool looking as they really are XD
@joshcolbert4682
2 жыл бұрын
cause other people might make nusances and get the local ordinances changed, so i try to make the bike look like not as cool and fun as it really is
@fernandomartin4147
2 жыл бұрын
If you wanna make it faster straight pipe it. You have to cut off the exhaust and just leave the first part of the exhaust that is connected to the head of the motor. Trust me I did it and it gives it way more power and it will not break I swear I had it like that for like 3 months.
@JMB676
2 жыл бұрын
Hope all is ok bud haven’t seen you making much content, hope you come back to it and share more gas bike stuff and just show us what your up to. If you get a chance I hope you check out my channel but most of all stay tuned to my channel in about a month or less I’ll be posting some very cool frank builds I’m doin all myself in my bedroom/shop lol. Can’t wait to silhouettes how I do it, I have wanted to build one ever since I started in the hobby a lil over a year ago now.
@erikwolf2771
2 жыл бұрын
I News Money!
@matthewpeter4034
3 ай бұрын
Dude I think the kit I bought doesn't have a removable head lmaoo
@jerryb1234
2 жыл бұрын
He's not back, he only does a video whenever somebody sends him a freebee, (smh)
@MotoredLife
2 жыл бұрын
Got a few more to get through then i get to show off my projects!
Пікірлер: 74