Thank you thank you thank you!! Brand new lathe owner here, every video I've come across completely skips this step (the most terrifying as a new lathe owner) and it's been driving me crazy!
@daveswoodshop782
7 жыл бұрын
I know the feeling. When I started turning I wished there was a video like this. That's why I posted it. Glad to help out.
@VictorAntonioLive
4 жыл бұрын
I agree Lynn!!!
@garymaynard7562
4 жыл бұрын
Thank you for the video showing the use of the spur drive and especially the correct way of finding the center of the piece to be turned. Very helpful video!!
@VictorAntonioLive
4 жыл бұрын
Simple and to the point...well done!
@thunderchild4816
6 жыл бұрын
Great video! Got a hand me down lathe and had no idea how to mount wood to it. Thanks a million!
@ShlisaShell
Жыл бұрын
I did not know they made spring loaded prick punches. 😍 I bought two. Thanks!
@daveswoodshop782
Жыл бұрын
You are very welcome!~ It does make it easier.
@andykliszcz9102
2 жыл бұрын
I'm glad I found this video. I've been trying to set up my lathe with wood and the wood keeps flying off and smashing against the wall
@astrofamily6081
3 жыл бұрын
thanks... i got it... was confused almost 2 weeks about how to put the wood, and that before watching this video
@davidbboarding
3 жыл бұрын
Great video! I believe the box for dead center you make, is because the pencil sits just a hair off the straightedge.
@amkii2
3 жыл бұрын
Great video!! Easy to understand and quick to get to the point. Thanks for the help.. this is exactly what I was looking for!!
@TastyBarrel
4 жыл бұрын
This is exactly the information I was looking for. Great informative videos. Thanks for posting!
@starhawke380
3 жыл бұрын
Great video, but I think you forgot an important step before turning on the lathe. Always hand spin the blank to make sure it clears the tool rest before engaging the lathe motor.
@IlanDavid
4 жыл бұрын
Sean Connery: "That's a nice piece of ash."
@OtterLakeFlutes
3 жыл бұрын
Thanks... I see people drilling a hole or not, and you've got a nice compromise with the punch. Now... I am moving to a safety drive for a bit. It's like the cupped dead center I believe you once showed, except it does have a spring-loaded point. I'm going to assume marking the center should be about the same procedure, and I'll just need to feel out how much pressure to exert with the tail stock so the workpiece only stops if I truly catch or manhandle (but it's not in danger of flying out anywhere in between!)
@guillaumepreudhomme4800
Жыл бұрын
Thanks Dave!
@KedaWoodDye
7 жыл бұрын
Thank You! Great demo! I owe you one buddy ;)
@daveswoodshop782
7 жыл бұрын
Thank you. Glad you found it helpful.
@robira1313
3 жыл бұрын
Is it really necessary, though, to find the critical center since you're going to make it round, anyway?
@daveswoodshop782
3 жыл бұрын
No, you are correct. You can be slightly off center and this will self correct as you round the piece. The downside to being off center is that the piece will wobble, you will have to reduce the turning speed to be safe and this will effect the cut. You will also have more waste material if you mount off center. It only takes seconds to find center and mount as I demonstrate in this video. It really is worth the effort to do it right.
@chaselee86
2 жыл бұрын
I've bought a round dowel instead of a spindle. What would be the best way to find the center of a circle?
@daveswoodshop782
Жыл бұрын
Exact same tool and exact same method. Just rotate the tool and draw a few lines and it will become obvious where the center is.
@grbroussard
5 жыл бұрын
Thanks! Perfect video for me.
@ScottEaton74
Жыл бұрын
I have been following these instructions but the spurs end up ripping out of the center when I apply pressure. Am I applying too much pressure? I am using carbide tools. Any help would be appreciated.
@daveswoodshop782
Жыл бұрын
Without seeing what is happening it is difficult for me to say. With that said.....If the spur is tearing up the wood while it is spinning it may be possible that the wood is not secured tight enough and is spinning loose resulting in the tearing. If it is ripping the wood before you even start turning then it might be too tight. I tighten just enough so the wood does not spin free of the spur while I am cutting.
@ScottEaton74
Жыл бұрын
Thanks for your quick response. I will keep working on it. I guess I just need to keep trying it until I find "just enough".
@mashupman1
4 жыл бұрын
what's the name / brand of your lathe? I love how its so quiet
@daveswoodshop782
4 жыл бұрын
It is a Jet 1221VS
@amritagardiner8064
4 жыл бұрын
How deep did you use the Mallet ? did all of the Spurs go through the wood or only the point?
@daveswoodshop782
4 жыл бұрын
The spurs must enter the wood or else the wood will not spin. If you were able to get it to spin it would certainly stop when you engage the cutting tool. The spurs are what enable the drive center to turn the wood.
@amritagardiner8064
4 жыл бұрын
@@daveswoodshop782 Thank you! that makes sense :)
@tracykerr2250
Жыл бұрын
My spur tends to drill into the wood as I’m turning. Leaves a hole similar to what a spade bit would. Is this normal??
@daveswoodshop782
Жыл бұрын
Is your spur just a single point or does it have small blades beside the point like the one in my video? If it is like the one in my video the solution is easy. It is spinning because it is not tapped in deep enough and you are not screwing it in tight enough.
@tracykerr2250
Жыл бұрын
@@daveswoodshop782 I am very new to this. We can seem to get the spur in deeper, don't know what we are doing wrong. It is just like the one you have with the "wings"
@daveswoodshop782
Жыл бұрын
@@tracykerr2250 What species of wood are you using. Are you putting the drive spur into end grain? Have You tried another piece of wood as this piece might be bad? What type of tailstock are you using? Does that look similar to mine? if it does you have to tighten it enough so that the spur completely penetrates the wood and the outer circle is tightly against the wood.
@yvonnex123
4 жыл бұрын
What if your piece of wook has a thiner (less than) diameter than the center pin youre trying to hammer into it?
@daveswoodshop782
4 жыл бұрын
They make drive centers with a smaller diameter then the standard size I show in the video. These drive centers are made for the purpose of being able to turn blanks with a smaller diameter. There are times when even these smaller drive centers are too large. In that case I use a chuck instead of a drive center. You can support the other end with a 60 degree live center. It will support the wood blank with it's point yet still have plenty of clearance to have access to the entire piece of wood. Just Google Nova Chuck and 60 degree live center to get a better visual image of what I am talking about.
@tpark89
2 жыл бұрын
Perfet. Thank you!!
@CC-gv6us
5 жыл бұрын
Thank you
@donyportillo790
6 жыл бұрын
How far into the spur do you drive it in?
@daveswoodshop782
6 жыл бұрын
Great question. I never quantized it with a specific depth. I just make a couple of taps, enough so that the spurs penetrate the wood. it doesn't have to go in too deep. Tightening at the tailstock will provide the pressure needed to ensure that the spurs stay engaged and don't slip.
@bartestes2587
6 жыл бұрын
Thank you.
@WoodworkingbyAsher
3 жыл бұрын
Hello Dave, You make outstanding videos. I'm a woodworker that is trying to get into KZitem and have included link cards from my videos to yours since they are so high quality. I was wondering if you could include link cards to some of my videos, I hope you will find them valuable. Would've reached out to you through email but I couldn't find your contact information anywhere. Thank you, Asher
@danielburns7519
3 жыл бұрын
I knew I was doing something wrong.
@Nikkimaya1
4 жыл бұрын
Great information. Although the way you talked it sounded like you were teachings rhis to a bunch of kindergarten kids.
@daveswoodshop782
4 жыл бұрын
That's probably because I taught Kindergarten through 3rd grade for 40 years. Old habits die hard. Not intended to be condescending. The good news it it provided me with the skill set necessary to break things down to their basic parts and then impart that knowledge to others.
@RightHereRightNow00100
2 жыл бұрын
@@daveswoodshop782 I think that's why I liked it so much, you talk clearly, friendly, and you make no assumptions that we know anything already.
@garyduran1
7 жыл бұрын
Thanks again!!
@daleleibfried8648
5 жыл бұрын
My spur center does not come out easily.
@daveswoodshop782
5 жыл бұрын
Are you saying that it is difficult each time you try to remove it or that you can't remove it at all? If it is difficult you have to clean the spur center and where it plugs in with a solvent to remove all grease and gunk. Both surfaces must be perfectly smooth. The slightest debris will cause binding.
@daleleibfried8648
5 жыл бұрын
@@daveswoodshop782 it is fixed to the lathe, so without disassembly it doesn't come out. I guess my question is, do I tap the stock into it or just tighten the machine until it seats. Thanks for your help.
@daveswoodshop782
5 жыл бұрын
I have never heard of a spur center that does not come out but if this is really the case then I would hold the wood against the spur center and give it a tap with the soft mallet before I tightened the Live center to it.
@talljimh
4 жыл бұрын
@@daleleibfried8648 I didn't think mine came out either, but turns out it was just stuck in there (probably from debris since it's a used lathe). I was able to put a punch on the other side of it and tap it out (toward the direction of where you mount) and it came out with a gentle tap.
Пікірлер: 54