Be careful not to put too much pressure on the screws when adjusting the polar scope, it can crank the reticle
@Satis22
Ай бұрын
Thank you for the video. It helped, although In my case, everything had to be adjusted. I must say adjusting the polar scope was by far the most difficult. Everything was wobbling and the adjustments were so minimal I had barely noticed them. I hope I'll never had to go through this again...
@chasingluminance
Ай бұрын
Yeah, I can be annoying to do
@FieldingSmith
3 ай бұрын
Both my laser and scope are so loose in their mounts that this has been a pita for me. And as soon as I think i get the scope centered, I use the laser pointer without the scope mount and its a good 6in off at 50ft. /sigh. And both the cell phone holder scope mount and the regular scope mount don’t point in the same place… about to throw them out and order a set of “calibrated” ones… but now I have trust issues lol
@Javidel25
Ай бұрын
Hola, quizás sea una pregunta tonta. He alineado el nomad con el laser y me ha dado buenos tiempos de exposición. Pero al intentar afinar la alineación con el visor polar, veo que el laser y el centro de la retícula no coinciden. En otros vídeos he visto que en el antiguo msn la polar no se coloca en el centro de la retícula . En el Nomad donde coloco la polar exactamente. Gracias y buen trabajo
@ManexFX
7 ай бұрын
Very useful video, thank you!
@chasingluminance
7 ай бұрын
Glad it was helpful!
@Anadrolus
17 күн бұрын
Is it not possible to attach a higher quality scope ? And that is illuminated.
@CMikeGo74
6 ай бұрын
This did not work at all on my MSM Nomad. Even a small 1/4 turn and the threads where so loose it moved over 8-10" at 20 feet just grabbing the laser and moving it up and down. Entirely too much play in threads to perform this.
@chasingluminance
6 ай бұрын
We're you spinning the laser or the mounting bracket?
@MathewTooherPhotography
5 ай бұрын
I agree, this method didn't work for me at all, too much play in threads, thwre must be a better way to calibrate, anyone have any ideas?
@chasingluminance
5 ай бұрын
@@MathewTooherPhotography you can roll it on s table to see the movement too
@roryhaymanphotography8882
7 ай бұрын
Hello Alex, new subscriber here. Thanks for the video. I'm considering the nomad but a little concerned these 71 year old eyes won't be able to see through the polar scope or even get a rough alignment with the laser. Have you had any experience with the phone mount tool? Thanks again
@chasingluminance
7 ай бұрын
Let me ask you 1st... how well do you do seeing individual stars? If you are OK with that - I think the laser should work pretty well for you
@roryhaymanphotography8882
7 ай бұрын
@@chasingluminance Depends on how bright the star is. I can make out polaris just barely. I've seen alignment phone apps that look pretty easy to use and see (sky safari 7+) but wonder how well it might work with the nomad. Thanks again
@chasingluminance
7 ай бұрын
@roryhaymanphotography8882 they work well and the phone adaptor for the nomad is pretty sweet. I do think the laser will generally be more accurate But I shall test
@haonguyen7370
7 ай бұрын
I have the moveshootmove, with its polar scope. Does that fit into the nomad's polar scope adapter or would I need a compatible polar scope? Thanks!
@chasingluminance
7 ай бұрын
If it's the scope "a" it will fit. Does it have the little bubble level?
@haonguyen7370
7 ай бұрын
@@chasingluminance that must be the newer one, my polar scope doesn't have a bubble level in it, thanks for checking!
@mattanous
7 ай бұрын
did Laura make that hat for you
@chasingluminance
7 ай бұрын
I did
@johncallery814
7 ай бұрын
Thanks for doing this tutorial. I went ahead and calibrated my laser. It was off just a little. I adjusted one adjustment screw by a quarter turn and then adjusted the other adjustment screw also by a quarter and little by little I got the beam in the crosshairs. I think the fact that the laser beam in the Nomad has to travel through that thin tunnel for 1.5" helps with accuracy. My take is as long as the laser beam cleanly exits the end of the Nomad and is not diffused you are going to be pretty accurate at least at 50mm or less. Before calibration I have shot at 30 seconds with my Samyang 135 and I don't have star trails. I'm looking forward to seeing how well I can do with just the calibrated laser with the 135mm lens. And if your laser battery runs out you can still eyeball Polaris by removing the laser and looking through the hole / tunnel.
@chasingluminance
7 ай бұрын
You're probably right about that
@kurtruppel6156
53 минут бұрын
Another well done video Alex, thank you.
@keithe3232
6 ай бұрын
'Promo SM' ✋
@agneschan1484
Ай бұрын
Very informative. Thanks. Would like to find out what is the function of the brass screw. Does it need to be adjusted?
@jayfoucheux6390
6 ай бұрын
Excess play when threading the laser onto the tracker...I find that there is still too much play when turning the laser to project the beam onto the paper bag. To remedy this I put a couple of wraps of teflon tape around the threads. This provide just enough tension and tightness to keep the pointer from moving too much. When done, the tape easily comes off of the threads. I tried this and it worked great. Thanks for the informative video.
@chasingluminance
6 ай бұрын
Cool idea
@weirfpv669
2 ай бұрын
Hi, I enjoyed your video, however I wanted to mention that when using the polar alignment scope, the celestial pole is what is centered in the crosshair not Polaris itself as the star is offset slightly from true celestial pole. Using various apps will assist with aligning Polaris to the correct position for your location and time.
@chasingluminance
2 ай бұрын
Correct. I was just using those criss hairs for calibration
@huf67
7 ай бұрын
I bought the laser for my Sky Guider Pro and use it to polar align first. After it's polar aligned, and my camera is attached to the ball head, I'll then lay the laser between the rails on the cameras hot shoe and use it to help aim at what I'm trying to photograph. Dual purpose.
@CMikeGo74
7 ай бұрын
I cant believe they don't calibrate those before shipping them out
@chasingluminance
7 ай бұрын
They do, but sometimes they get out of alignment
@bernym4047
7 ай бұрын
Very useful. It reminded me I have an engineer's V block that I can use for aligning my laser. Thank you. Avery clear explanation.
@chasingluminance
7 ай бұрын
Glad you enjoyed
@RunCatRun
7 ай бұрын
Hi. Big thanks for another video about small things that matter. And video sequence is better now 👍🏻 Thank you, Alex!
@chasingluminance
7 ай бұрын
Glad you liked it!
@marianovictor
7 ай бұрын
So for the older MSM I had watched your video on how to calibrate. It was so difficult to rotate the laser evenly because it is wobbly in the holder. I went to the hardware store and purchased a brass bushing and then drilled it out slightly to fit the laser. With the bushing in the holder I rotated the laser and it did not wobble. I was able to get a better adjustment. If you have an email address I can send you a photo the bushing set up.
@chasingluminance
7 ай бұрын
Chasingluminance@gmail.com
@azza9304
3 ай бұрын
What a super helpful guide, thank you for sharing this kind of insight
@chasingluminance
3 ай бұрын
Glad you enjoyed
@guykerr8111
7 ай бұрын
Just a bit frustrating that it is not done before shipping. Thanks,.
@chasingluminance
7 ай бұрын
They do, but sometimes things still happen
@pazoulay
7 ай бұрын
Hi Alex. Asking a stupid question. When calibrating the laser, what part are you spinning? the red screw with the pointer solidly seated within it? or the pointer as you are threading it into the red screw (with the red screw tightly in the rotator already)? Whichever way you spin, at some point you reach the point where it is fully screwed in. This is what is different with calibrating this pointer as opposed to the one with the old one.
@pazoulay
7 ай бұрын
My situation is that the pointer just shifts a bit along just the y-axis in the final rotation before it is fully screwed into the rotator, and frankly I am afraid of making things worse rather than better.
@chasingluminance
7 ай бұрын
I'm spinning the laser as I thread it in. And I'm only testing the rotation right before it's completely tight. For me it doesn't move around too much
@pazoulay
7 ай бұрын
Thanks. I think I am going to leave it alone because it truly does not move a lot. What is bizarre is that when you look into it (batteries off) it looks out of center (as it did in your helpful video)@@chasingluminance
@josepmbernaus
7 ай бұрын
Great video! Thanks for sharing. Have you tried to phone mount for polar alignment? I live in a country where the lasers are forbidden, so I cannot use it, but I was wondering if the "first approach" polar alignment with the phone mount also needs calibration. Just wondering... Thanks for your videos, very useful! Looking forward to the new one!!
@chasingluminance
7 ай бұрын
I did with the move shoot move kzitem.info/news/bejne/0W2EyZV4iqqXd6Asi=aUFPq1jMP6z4vVF8
@josepmbernaus
7 ай бұрын
Yes, I watched that one too, really interesting as well. Will you try it with the Nomad in the ‘near’ future?
Пікірлер: 54