Hey your MIVV exhaust looks and sounds amazing. Probably will get one for my 200 Duke
@GuruBoards
10 ай бұрын
This video makes me think you can use the MSD 82803 coil
@ayosflame
Жыл бұрын
Pizzas ready
@HaenaPerformance
Жыл бұрын
What kind of improvements did you see?
@RhoadsChristopher
Жыл бұрын
Still working on that. I'll have a video out soon to talk about it. I've been working my way up to make sure there is no random misfires of anything prior to hammering it into full throttlr.
@jtwobickful
Жыл бұрын
Dinners ready video over lol
@RhoadsChristopher
Жыл бұрын
Hahaaha I was wondering if someone would catch that.
@golfvictor395
9 ай бұрын
Here where i live msd pn 8232 is mostly used on carb type engines rather than injection. I currently own one and i was wondering if it is possible to use it on injection. On long term run you experienced any problems? .... my major concern is that carb engines use CDI ( capacitor discharge ignition i think) while injection motors use TCI ( Transistor Coil Ignition). The weird think is this tower is that is "called" CPC ignition that stands for Coil Per Cylinder. On diagram of the coil tower though you can see that the three wires are like this: one is ground to the block, one is the trigger where it says 500v or 12v trigger (means both cdi and tci can be used???) And the third one says that is 12v. On my knowledge the tci ignitions are using two wires one continuous 12v supply and the trigger from ecu, while the the cdi used only one coming from the cdi "ecu". Veey confusing 😂
@RhoadsChristopher
9 ай бұрын
Ice been running the 8232 for a good bit now with ZERO issue. Runs great!
@RhoadsChristopher
9 ай бұрын
Also, it is a 3 wire as you explained. If you probe your wires you will see which is setup for hiw you explained. Hiwevwr, I did explain how to wire it up in the video.
@golfvictor395
9 ай бұрын
No the wiring is straight forward what I was looking actually was if it was working properly for the reasons mentioned above. Will try out also my msd to my WR and see the results 😅
@RhoadsChristopher
9 ай бұрын
@@golfvictor395 let me know your findings.
@sabariunni3919
Жыл бұрын
🔥
@JH09SUMIT
Жыл бұрын
Can you tell me which wire in the ignition coil can provide an RPM signal? I'm looking for an RPM signal for my Arduino. Does the negative terminal in the ignition coil provide a pulsating 12v signal. because I've seen people hooking up external tachometer using signal from that terminal
@RhoadsChristopher
Жыл бұрын
It should be the negative. The 12v is just a constant power source.
@HaenaPerformance
Жыл бұрын
What was the verdict with the msd ignition? Worth the install? did it make any difference? Smoother? More responsive?
@RhoadsChristopher
Жыл бұрын
I tested spark and it seems like there is more spark energy. However, without a dyno there is no way to prove any added power. However, it revs and runs smoothly and I've slammed the limited and I've had no issues with this setup. One good thing is that it's cheaper than buy an oem unit and feels like much higher quality.
@andreass4833
11 ай бұрын
Hey I got one and I’m trying t connect it on my 150cc pit bike and I don’t understand how t connect it with the 3 wires?? Very confusing
@RhoadsChristopher
11 ай бұрын
So the black wire just grounds to the frame. You have the red wire which will be constant 12v. The other wire is just a signal wire. That just goes to the last wire you have left over. Use a multimeter and see which of the two wires has constant power.
@andreass4833
11 ай бұрын
@@RhoadsChristopher still doesn’t work if you could tell my your instagram or Facebook so I can show you pictures so you can help me
Пікірлер: 21