bro i wanted to see how you hooked up the speaker wire to amp and you did not show that side of amp at all...
@theREALhighnoon
5 ай бұрын
Same! My screw doesnt screw all the way down and the speaker wire is so small! How does it stay connected?! I think I even stripped the screw screwing it in too much!
@csonracsonra9962
3 ай бұрын
@@theREALhighnoonadd a spacer in there I'll make the speaker wire larger and put a Ferrell on the end of the speaker wire
@abismaellatorre6144
4 ай бұрын
Does this amp go into protective mode? I have everything hooked up and I've tested everything I could but I have no sound... Any suggestions?
@jaedarzadon
4 ай бұрын
Ground the RCA shield. Take a piece of wire, touch one side of it to bare, clean metal of car and other side to one of the RCA shield on the amp to test and see if you get sound. If you do, then just solder the wire to RCA and mount other side. That completes your signal to ground.
@downhilldaddy5282
13 күн бұрын
Is the bass remote connected?
@abismaellatorre6144
8 күн бұрын
@@downhilldaddy5282 yes it was connected...
@SrsLe33
3 ай бұрын
I don't understand the 3 switch settings
@roccoorlando1516
2 жыл бұрын
I want to run one skar SDR 12 1200 watt with this amp is it compatible
@jaedarzadon
2 жыл бұрын
It should be fine, which most subs would.
@freegamexavier
3 жыл бұрын
What does it mean when it’s keeps blinking ?
@jaedarzadon
3 жыл бұрын
I don't know. You might want to check out a manual online.
@bradleykidd3046
2 жыл бұрын
Check your ground, that was my problem
@BeastlyGamer
2 жыл бұрын
My red lights stay on even when the car is off😒
@JohnDoe-nm9et
2 жыл бұрын
@@BeastlyGamer That means whatever source you’re getting power from is constantly using power
@Deano_42
2 жыл бұрын
@@BeastlyGamer yeah thats not good. You might want to buy like a cut off switch or something. Make sure the amp goes an stays off when you turn your car off
@samuelsanche1619
2 жыл бұрын
Was told they couldn’t mount the amp to the box. Was curious why
@jaedarzadon
2 жыл бұрын
That's not true BUT when you mount the amp with the screws, if the holes created goes through the wall of the enclosure, air gets leaked out in a sealed box. In a sealed box application, the air pressure inside is what helps the control movement of the cone of the subwoofer so it's important your screws don't go all the way through (use shorter screws) or you figure out how to seal each hole like using silicone. In a ported enclosure application, it's not as critical. Hope that helps.
@NandoCapone
2 жыл бұрын
If you mount it to the box pre drill screw holes and use a tap like you would for drywall with sealant the tap will expand inside the box
@donkryda13
Жыл бұрын
I only have 2 red lights on not 3 what do I do ?
@robertomoreno5526
7 ай бұрын
I'm planning on getting the hifonics Zeus 3200 amp .witch one is better. 😮
@jaedarzadon
4 ай бұрын
It's a matter of brand you like coz they are the same to me.
@jeremygreen72414
Ай бұрын
Zeus by far
@isie8637
2 жыл бұрын
Do i need to bridge to connect to my mtx subwoofers?
@jaedarzadon
2 жыл бұрын
It's about how you configure your subs. It can take a low impedance load.
@BeastlyGamer
2 жыл бұрын
Do the red lights turn off?
@jaedarzadon
2 жыл бұрын
They are status lights. If they turn off, the amp is off
@trualpha
2 жыл бұрын
what does the white plug all the way on the left do
@jaedarzadon
2 жыл бұрын
I believe it's high level input (head unit power from OEM radio).
@csonracsonra9962
3 ай бұрын
That's what I'm here to find out the five pin plug on the left
@michaelalford4752
3 жыл бұрын
Are those red lights suppose to be on
@jaedarzadon
3 жыл бұрын
That's how they designed it to have the lights on. Thanks!
@BeastlyGamer
2 жыл бұрын
@@jaedarzadon all the time? Mine stay on even when the car is off... Is that normal?
@ShaneGuyton-mj1mv
6 ай бұрын
@@BeastlyGamerNo! 😂
@1280spoon
Ай бұрын
Thats not normal you may need to find a source that turns off when your vehicle is turned off you may can tap in your cigarette lighter fuse try that and see if turns off when vehicle is turned off@BeastlyGamer
@yungrichrico2159
Жыл бұрын
So can u use this for speakers and sub ?
@jaedarzadon
Жыл бұрын
Designed for subwoofer. It's a mono amplifier.
@rhondabrown7432
2 жыл бұрын
I need to know which is the hot and the ground
@jaedarzadon
2 жыл бұрын
Left most closest to the edge is ground (-), middle is trigger (remote), last one towards middle of the amp is positive (+/hot). It should be marked on the amp.
@csonracsonra9962
3 ай бұрын
@@jaedarzadon😮 good on you for answering this because I could not have it is clearly labeled right there at the terminals
@caydenvanoverwalle3809
2 жыл бұрын
My subs have cut out twice with these after using them for a while and the amp gets super hot what do I do??
@jaedarzadon
2 жыл бұрын
Adjust your gain and lower it. Make sure your signal is clean with no square waves. Secondly, the impedance (speaker config), box type, and signal can run your amp at tremendously low impedance so yes it will get super hot and shut down in protection mode.
@caydenvanoverwalle3809
2 жыл бұрын
@@jaedarzadon how do I avoid square waves?
@csonracsonra9962
3 ай бұрын
@@caydenvanoverwalle3809You're going to need an a oscilloscope first
@austinvapes2808
2 жыл бұрын
How do I get more boom out of the subs
@jaedarzadon
2 жыл бұрын
That is a bit complicated of a question. I will assume when you say boom, you are talking about more volume/louder. The enclosure for any subwoofer is a big part of the equation. Each type (sealed, ported, isobaric, etc.) have advantages and disadvantages. Power from the amps obviously has something to do with it. My advice is it doesn't matter how much power you have if a sub is in the wrong enclosure (too small, too big, not correct type, etc.) so you'll have to figure it out from there.
@austinvapes2808
2 жыл бұрын
@@jaedarzadon I mean the when the Bass hits on my subs my bad lol
There's a number of reasons why a sub may not hit hard. It could depend of type and design but if it's technically only because of the amp and you've tried a different amp to compare then you may have to check the amp. There are different variables including impedance that affect the power output. The output voltage from your head unit and the gain adjustment on the amp as well. The wiring size is also something to check and getting good ground. Another thing that get overlooked is if the vehicle's electrical system can actually handle or provide enough amperage (current) for the amp to perform properly. Check some of that stuff to determine if that's causing the issue. Hope that helps.
Пікірлер: 54