Finally a video with good lighting, clear explanation and useful tips. I cannot stress this enough......THANK YOU!
@BIGWILLSCARCARE
3 жыл бұрын
@Vytautas Olberkis Glad it helped. Thanks for watching please like and Subscribe if you haven't already
@ChickeN-mc3oi
2 жыл бұрын
Not gonna lie this was my first time ever doing a clutch let alone taking out a transmission I wouldn’t have been able to do it without this video. A couple extra tips for newbies: 1- clutch alignment tool must be used to center the clutch don’t just put it in and think you’re okay or you will not be able to put the input shaft through the pilot bearing/flywheel, you must hold it almost the exact center of the opening and tighten down the pressure plate while holding it centered still 2- Organize your shit or you’re gonna have to drive to subaru to buy multiple bolts covered in grease 3-for axel reinstall once axel is aligned and will not go in any farther but there is still a gap: use center section as a “hammer” and hit the end into the transmission 3/4 times, if it does not go in, immediately spin the axle 180 degrees (to align the snap ring at the end of the axle) and repeat
@BIGWILLSCARCARE
2 жыл бұрын
@Chike N Thanks for watching please Like, Share and Subscribe if you haven't already
@duncobra
3 жыл бұрын
This guy knows exactly what he was doing unlike some people who just do some video with guess work. Great explanation.
@BIGWILLSCARCARE
3 жыл бұрын
@Duncan Kiruthi Thanks for watching please Like and Subscribe if you haven't already
@petergrimm3827
Жыл бұрын
Hey man I have to thank you incredibly. I was able to do my clutch on my own. Outside on the ground. I have so much more confidence now thanks to you and this video. I'll update after my 1000 mile break in
@BIGWILLSCARCARE
Жыл бұрын
Thanks for watching please Like, Share and Subscribe if you haven't already
@deigobams3
Жыл бұрын
Just followed this step by step while doing my clutch. I know this is old, but people are still using it. Worked out great. Thank you!
@FingerPulse
Жыл бұрын
Out of curiosity, how long did it take you?
@BIGWILLSCARCARE
Жыл бұрын
Glad it helped. Thanks for watching please Like, Share and Subscribe if you haven't already
@drlowden
3 жыл бұрын
Best vid on the subaru clutch change so far
@christopherstuppy8574
2 жыл бұрын
This is an amazing video! Great detail with amazing tips and tricks along the way, excited to get wrenching!
@BIGWILLSCARCARE
2 жыл бұрын
@Christopher Stuppy Thanks for watching please Like and Subscribe if you haven't already
@DM-tf6mk
2 жыл бұрын
Absolutely amazing detailed video! I've worked on cars since I was a teenager but never replaced a clutch on a Subaru and my buddy just asked if I could help him.
@BIGWILLSCARCARE
2 жыл бұрын
@DM1406 Thanks for watching please Like and Subscribe if you haven't already 👍
@atallah24
Жыл бұрын
Nice video, much like everyone else it was great to see it come together before performing it on my own!
@jayski8987
Жыл бұрын
Thank you for this. Very informative and you do great work 👍🏼 looks like you know what you’re doing and I can tell you take pride in your work. We need more mechanics like you in this industry. Anyway I’m getting ready to do a clutch job on a ‘19 WRX for a buddy of mine. I’ve done hundreds of clutches in my life just not on a Subaru and watching your video first let me know what I’m in for. I’ve been wrenching on heavy duty class 8 trucks for a living for 31 years now and it looks like this job will be a piece of cake compared to a 15 inch clutch that weighs 150lbs, a flywheel that weighs 100lbs and removing a transmission that weighs 600lbs. 😂 You make clear and detailed videos that help the average person repair their cars. Keep doing what you love and you’ll never work a day in your life.
@BIGWILLSCARCARE
Жыл бұрын
@JaySki Thanks for your feedback it's viewers like you that keeps me motivated, and that is why I read and respond to all my comments 👍. Thanks for watching please Like, Share and Subscribe if you haven't already
@drksrsx4024
Жыл бұрын
100% worth watching before I got started, thank u!
@BIGWILLSCARCARE
Жыл бұрын
@Drk SrSx Thanks for watching please Like, Share and Subscribe if you haven't already
@fixflickss
Жыл бұрын
The best video on how to do this properly, thank you, keep making great videos.
@BIGWILLSCARCARE
Жыл бұрын
@Fix Flicks Thanks for watching please Like, Share and Subscribe if you haven't already
@shaundrezek4330
2 жыл бұрын
You are a savior. This must be the most well put together instuctional video I've ever used for a bigger job like this. Great vids man.
@BIGWILLSCARCARE
2 жыл бұрын
@Shaun Drezek Thanks for your feedback please Like and Subscribe if you haven't already and also support my IG BIG WILL CAR CARE
@janbakker9866
Жыл бұрын
Great video sir! Doing this right now. Best how to I've seen ! Lots of little tricks. Love the tie strap idea to rotate the motor
@BIGWILLSCARCARE
Жыл бұрын
@Jan Bakker Thanks for watching please Like, Share and Subscribe if you haven't already
@AutoExpectations
4 ай бұрын
Great detail video, best one on utube without a doubt.
@BIGWILLSCARCARE
4 ай бұрын
Thanks for watching please Like, Share and Subscribe if you haven't already
@vfr661
Жыл бұрын
Thanks for the details. Really help with the clutch replacement. 😊
@BIGWILLSCARCARE
Жыл бұрын
@vfr661 thanks for watching please Like, Share and Subscribe if you haven't already
@Saguillealonzo
3 жыл бұрын
Some people pull the motor out instead of the transmission to replace the clutch on these cars. Which method do you think is the easiest?
@BIGWILLSCARCARE
3 жыл бұрын
@SG Alanzo I prefer to remove the transmission instead of the engine, where I would have to worry about removing wiring harnesses, engine mounts and using engine lifts plus whatever else that might be in the way. Thanks for watching please Subscribe if you haven't already
@nelsonsanchez9877
11 ай бұрын
Hey man do you by chance know where the firewall ground strap connect to? I think it might have broke it lol! Does it connect to the transmission? Awesome vid by the way helped a lot! 💯
@BIGWILLSCARCARE
11 ай бұрын
Yes it does. One onto he transmission and one on the engine. Thanks watching please Like, Share and Subscribe if you haven't already
@briancase863
Жыл бұрын
Very nice video, Just the right amount of explanation. Good camera work. Well performed without hacking like a lot of other guys. This was very helpful. Tomorrow I plan on buying a WRX and am now totally comfortable that i can handle the clutch replacement. Thank You.
@BIGWILLSCARCARE
Жыл бұрын
@Brian Case Thanks for watching please Like, Share and Subscribe if you haven't already
@romeo3306
2 жыл бұрын
Thanks for taking the time to this in depth video! Your awesome!
@BIGWILLSCARCARE
2 жыл бұрын
@Romeo Thanks for watching please Like and Subscribe if you haven't already
@joeswansom69
Жыл бұрын
Thank you for sharing a great video it’s awesome very detailed 🙏👍
@BIGWILLSCARCARE
Жыл бұрын
No problem 👍 Thanks for watching please Like,Share and Subscribe if you haven't already
@ryansanders5055
2 жыл бұрын
Would this be the exact method to use for installing a 2017? Lastly how do I know if I need to replace my clutch or my clutch and flywheel? Thank you! very informative video
@BIGWILLSCARCARE
Жыл бұрын
@Ryan Sanders it should be the same or very similar. if your clutch is slipping , shifting is difficult, burning smell, gears only shift at high RPM are all signs of a bad clutch and if you are replacing you might as well replace the flywheel because it will be easily accessible at that point. Thanks for watching please Like, Share and Subscribe if you haven't already
@playlist8395
2 жыл бұрын
I believe the 8 mounting bolts on the flywheel are 22.1 ft-lb for the WRX and 55.3 ft-lbs for the STI.
@BIGWILLSCARCARE
2 жыл бұрын
@Vernon Babich Thanks for watching please Like and Subscribe if you haven't already. Also follow me on Instagram Big Will Car Care
@RobHTech
2 жыл бұрын
Why not just remove the lower ball joint for the axle removal so not to mess with the alignment? great vid. Why not put the wratching strap on before you unbolt the trans?
@BIGWILLSCARCARE
2 жыл бұрын
@RobHTech I would do that if was replacing the ball joint due to damage that may occur upon removal. Thanks for watching please Like, Share and Subscribe if you haven't already
@rossifumifan1
Жыл бұрын
This video is fantastic! A thousand thanks sir.
@BIGWILLSCARCARE
Жыл бұрын
Glad it was helpful! Thanks for watching please Like, Share and Subscribe if you haven't already
@mikephillips7048
Жыл бұрын
@BIGWILLSCARCARE great detailed video, thank you! I just had my 2016 WRX clutch, throwout bearing, pilot bearing, and clutch fork replaced at 59k miles due to throwout squealing and clutch fork chattering. It's a new upgraded clutch (South Bend), new stock TOB, and new upgraded fork that should be same dimensions as stock. Engagement and shifting is smooth and tight, but when I picked up the car, I immediately noticed a noise when depressing the clutch almost like the former TOB noise but more of a metal sound like rotational friction. It gets fainter as the clutch heats up but does not go away after several break-in trips of light use. Could my mechanic have not used enough grease on the shaft that the TOB rides on, maybe misaligned the clutch fork, or should I have replaced the pivot ball to mate up better with the new fork's pivot socket to provide better fork alignment and prevent play? Is there anything you would suggest besides tearing back down to find the source of this grinding noise (expensive)? The mechanic said to keep driving it to see if it goes away but that does not seem like a good idea (I don't want to damage the shaft or the pressure plate). I have liked & subscribed due to your detail and knowledge and look forward to watching your other vids, especially for CV axle replacement since that's next. Thank you!!
@BIGWILLSCARCARE
Жыл бұрын
@mike phillips sorry for the late response but maybe your mechanic didn't use any grease at all or the wrong grease and I have seen where mechanics removed the old parts and didn't clean the surface before installing new parts. Thank you for supporting my channel 👍
@turbo6mtawd
3 жыл бұрын
Very professional video. You deserve more views.
@BIGWILLSCARCARE
3 жыл бұрын
@Redemption Thanks for watching please Like and Subscribe if you haven't already
@AutoExpectations
4 ай бұрын
Was this the 5 speed or 6 speed transmission I notice while taking my STI 6 speed it's very similar
@BIGWILLSCARCARE
19 күн бұрын
I can't remember which one it was but they are similar. Thanks for watching please Like, share and Subscribe if you haven't already
@seraph6843
10 ай бұрын
Im having problems with the pull clutch i ordered. Are these clutches the pull or push type stock?
@BIGWILLSCARCARE
10 ай бұрын
It is push I believe, if the fork is facing the rear of the car it is push. Thanks for watching please Like, Share and Subscribe if you haven't already
@justinking2759
2 жыл бұрын
The most informative video for WRX clutch install yet. I do have one question if I could trouble you to help me, please! I have replaced the clutch and am installing onto engine but having difficulty getting the tranny to completely mate to the engine without some resistance. I was wondering if accidentally moving the lever while handling the transmission while removing that is actuated by the shift cable that has been detached, would impact the re-assembly. I don't honestly know what gear it may be in as I've hit that damn lever and actuated the shift lever to the right rear of the tranny which sounds like I have changed the gears. I just don't know how much pressure to place on the transmission in order to get it to mate past the tabs on each side of the tranny. Should it press up to the engine block without resistance? I'm having to work the bolts on equally criss cross to get the tranny to move toward the block then get resistance once the tabs begin to mate up. Thank you for your input.
@BIGWILLSCARCARE
2 жыл бұрын
@Justin King I don't believe that should prevent it from mating. Make sure the engine is rotated towards the rear and the clutch is seated correctly. Use the clutch alignment tool. Thanks for watching please Like and Subscribe if you haven't already. Also follow me on Instagram Big Will Car Care
@zyco611
2 жыл бұрын
Having the same issue. What did you do about it? I also think I actuated something and got bolts in, and the go in without resistance until about 1 centimeter left. Help!
@ChickeN-mc3oi
2 жыл бұрын
@@zyco611 Did you get it figured out? im in the same spot i still have 2 inches to go… everything is aligning as far as i can see but still no progress
@titofeller1
2 жыл бұрын
Great video. One question how did you remove the top shifter cable?
@BIGWILLSCARCARE
2 жыл бұрын
@titofoller 16:00 to 18:11 minutes section is where I have the information. The angle wasn't good for me to record it but it's the same as the lower. Thanks for watching please Like, Share and Subscribe if you haven't already
@Hunter-og1sy
Жыл бұрын
You ever figure it out?
@Hunter-og1sy
Жыл бұрын
I got the bracket and clip off but not sure how to disconnect that top cable from the tranny
@BIGWILLSCARCARE
Жыл бұрын
@@Hunter-og1sy it's around the 17:28 mark of the video. Thanks for watching please Like, Share and Subscribe if you haven't already
@jeffflowers729
2 жыл бұрын
You left some things in place like the exhaust that makes the job a little easier than others have shown.Would this be the same procedure for a 2008?
@BIGWILLSCARCARE
2 жыл бұрын
@Jeff Flowers I'm not sure but it should be a similar process. Thanks for watching please Like and Subscribe if you haven't already
@jeffflowers729
2 жыл бұрын
@@BIGWILLSCARCARE Now that I'm digging into this project, I can see the 08 is different. The turbo on the right side is blocking at least one bell bolts so I will likely have to remove it. :( I might be able to get away with just removing the heat shield. But now wonder if I'll have to remove the exhaust on mine anyway :( I also snapped the top starter bolt. Hopefully there is enough sticking out of the block to grab it.
@lofihiphoptrio
Жыл бұрын
thank you for the video man helped me with my bugeye sti not gonna lie those rotors and shocks are looking crusty for a 2018 lol
@BIGWILLSCARCARE
Жыл бұрын
lol thats true. Thanks for watching please Like, Share and Subscribe if you haven't already
@KLNYC
3 жыл бұрын
Good video. What is those linkage on the transmission.? My is 2007 OB at 107K need to it.
@BIGWILLSCARCARE
3 жыл бұрын
@KwadKen can you give me the time stamp on the scene with the linkage? That way I can give you a direct answer. Thanks for watching please Like and Subscribe if you haven't already
@49razor
11 ай бұрын
Does the top shifter cable just pop off and has no pin holding it?
@BIGWILLSCARCARE
10 ай бұрын
I can't recall the exact set up but I believe I covered it in the video. Thanks for watching please Like, Share and Subscribe if you haven't already
@49razor
10 ай бұрын
you actually completely skipped how it was attached @@BIGWILLSCARCARE
@skrmnghrd4520
3 жыл бұрын
Hello! I assume it would be quite similar with the 2019 impreza base model? Except without the intercooler part? Nobody made a video on the impreza base models.☹️
@BIGWILLSCARCARE
3 жыл бұрын
@Skrmng Hrd it should be similar . Thanks for watching please Like and Subscribe if you haven't already
@Rhosticks
2 жыл бұрын
Wicked! Video tuff my yute. Bless up! Subscribed. 🤜🏾🤛🏾
@BIGWILLSCARCARE
2 жыл бұрын
@Rho Main thanks for watching. bless
@livin._.tokyo18
2 жыл бұрын
What's the the link to the clutch you used 2018 was a split year
@lopezam07
Жыл бұрын
Did you have to adjust the clutch pedal?
@BIGWILLSCARCARE
Жыл бұрын
No I did not have to make any adjustments to the pedal. Thanks for watching please Like, Share and Subscribe if you haven't already
@username-tv6uw
3 жыл бұрын
Please take your transmission apart video it and reassemble it for me please lol. this is the best video for 17 up clutch though. Not many videos out at all.
@BIGWILLSCARCARE
3 жыл бұрын
@Micheal Wittman lol appreciate the comment. Thanks for watching
@harveedeguzman5794
9 ай бұрын
Thank you about to try this tomorrow
@BIGWILLSCARCARE
8 ай бұрын
Did it work? Thanks for watching please Like, Share and Subscribe if you haven't already
@codykellner9985
3 жыл бұрын
Absolutely amazing good job man...great video
@BIGWILLSCARCARE
3 жыл бұрын
@cody kellner Thanks for watching please Like and Subscribe if you haven't already
@IkeandMike1
Жыл бұрын
Hey Big Will, I just completed replacing the clutch on my 2018 WRX, thanks to your video for about 90% of the info I needed to complete the job. How do I send you some cash? I'd rather not subscribe to Patreon, just want to send you a few dollars for saving me a lot of money. TIA
@BIGWILLSCARCARE
10 ай бұрын
Glad it helped you can email me for my info. Bigwillcarcare@gmail.com
@RACERVISION
2 жыл бұрын
Great video bro very detailed
@BIGWILLSCARCARE
2 жыл бұрын
@RACERVISION Thanks for watching please Like and Subscribe if you haven't already
@beemerkon
3 жыл бұрын
Like your style always knowing your socket sizes
@BIGWILLSCARCARE
3 жыл бұрын
Thanks for watching please Subscribe if you haven't already
@pirihern9329
3 жыл бұрын
D best video yet muchas gracias.
@BIGWILLSCARCARE
3 жыл бұрын
@Piri Hern Thanks for watching please Like and Subscribe if you haven't already
@n00baru24
2 жыл бұрын
Was there a reason you didn't address the rear main seal while you were there? Otherwise, thank you for this. I am very soon doing the work on a 2013 WRX, and I want to be as prepared as possible.
@BIGWILLSCARCARE
2 жыл бұрын
@n00barul the car was fairly new so and seal was in good shape. Thanks for watching please Like and Subscribe if you haven't already and also support my IG BIG WILL CAR CARE
@nestorlg007
3 жыл бұрын
What is the name of the pin when you take off the wheel? Just a cotter pin?
@BIGWILLSCARCARE
3 жыл бұрын
@Nestor Lanuzaa no pin removed just the nut for the axle a d its secured by bending the collar on the nut into a groove on the axle. Thanks for watching please Like and Subscribe if you haven't already
@natergordon
2 жыл бұрын
Extensions do not throw off the torque when using a wrench. Only impacts
@BIGWILLSCARCARE
2 жыл бұрын
@Nate Gordon Thanks for watching please Like and Subscribe if you haven't already
@jeanulloa5718
3 жыл бұрын
How lung did it take you to take it apart and replace the clutch?
@BIGWILLSCARCARE
3 жыл бұрын
@Jean Ulloa it can be done in a day with help. Thanks for watching please Like and Subscribe if you haven't already
@oOILLUMIN8TINGOo
2 жыл бұрын
Excellent vid.👍 thank you
@BIGWILLSCARCARE
2 жыл бұрын
@Jameslll Thanks for watching please Like, Share and Subscribe if you haven't already
@spoopdiewoopdie8092
3 жыл бұрын
Just curious in all. How long did it take you ? Lol. Amazing video btw
@BIGWILLSCARCARE
2 жыл бұрын
@Spoopdiewoopdie it can be done in a day if you have help or about two to three by yourself. Thanks for watching please Like and Subscribe if you haven't already
@oscarontiveros5117
10 ай бұрын
Very good video
@BIGWILLSCARCARE
10 ай бұрын
Thanks for the visit. Thanks for watching please Like, Share and Subscribe if you haven't already
@juliansaurus
2 жыл бұрын
Thank goodness my dealership is currently replacing it for me at no charge lol
@BIGWILLSCARCARE
2 жыл бұрын
@Julian Ospina 👍Thanks for watching please Like,Share and Subscribe if you haven't already
@BIGWILLSCARCARE
2 жыл бұрын
@Julian Ospina 👍 Thanks for watching please Like, Share and Subscribe if you haven't already
@mikeb5981
3 жыл бұрын
What brand of clutch did you put in it?
@BIGWILLSCARCARE
3 жыл бұрын
@Mike Barn oem. Exedy if I recall correctly. Thanks for watching please Subscribe if you haven't already
@username-tv6uw
3 жыл бұрын
@@BIGWILLSCARCARE what other mods do you have? I didn't see a big sf or anything?
@BIGWILLSCARCARE
3 жыл бұрын
@@username-tv6uw No mods just the clutch. Thanks for watching please Subscribe if you haven't already
@alexthegreat204
2 жыл бұрын
How much does it cost ?
@BIGWILLSCARCARE
2 жыл бұрын
@Alex Avalos the clutch kit was around $250 I believe.
@theyoungprodigy7509
2 жыл бұрын
I’m having a hard time finding the correct clutch kit for my car
@theyoungprodigy7509
2 жыл бұрын
Could you help me?
@BIGWILLSCARCARE
2 жыл бұрын
@The Young Prodigy I have to reach out to my customer and get back to you
@theyoungprodigy7509
2 жыл бұрын
@@BIGWILLSCARCARE Thank you man
@theyoungprodigy7509
2 жыл бұрын
@@BIGWILLSCARCARE Thanks man!
@jaysonbourne8841
2 жыл бұрын
My bwoy, yah yaad man????
@BIGWILLSCARCARE
2 жыл бұрын
@Jayson Bourne mich respect. Thanks for watching please Like and Subscribe if you haven't already
@jimjones5419
2 жыл бұрын
backyard mechanic
@BIGWILLSCARCARE
2 жыл бұрын
@Jim Jones Thanks for watching please Like, Share and Subscribe if you haven't already
@chriatiano749
Жыл бұрын
Seems like removing the engine would be easier
@BIGWILLSCARCARE
Жыл бұрын
Not necessarily but if it's more convenient for you then yes. Thanks for watching please Like, Share and Subscribe if you haven't already
@lard1892
2 жыл бұрын
Everything on a Subaru is easy to fix........
@BIGWILLSCARCARE
2 жыл бұрын
@Lard lol somewhat. Thanks for watching please Like and Subscribe if you haven't already
Пікірлер: 133