It’s probably worth noting if the actuator assembly rubs that area, you could pick up false knock and timing be pulled in the ecu. I have an issue right now with mine and first plan is to bend that metal out of the way if possible, and if that fails, I’ll have to try cutting the exhaust down and try to shift everything fwd a bit.
@GDaydreams
3 жыл бұрын
A good point. I definitely think that there is an issue from factory and you are right. The rubbing could be detected as false knock. If the factory exhause Co tinues to miss behave, I think taking a quarter of an inch out of the mid section would do the trick.
@jeremyluder494
3 жыл бұрын
So update on mine. I cut 1/2” from each pipe where headers connect to resonator portion. That allowed me to shift everything else forward as necessary for clearance. From there, I used liquid electric tape to repair the insulation on the wiring on both sides. If I have any issues still, I will resort to buying the harnesses. It is still curing as its a 24 hour cure once all layers are applied. If I don’t post in here again, it will be because it was successful.
@GDaydreams
3 жыл бұрын
@@jeremyluder494 - Brilliant. Thanks Jeremy. I would advise that you apply a bit of heat shielding tape after the electrical tape has cured. Just for that added protection :) Hope not to hear from you on this thread again haha
@nigelsmustangchannel4563
3 жыл бұрын
"Gen 2 Coyote for life" Hell yeah!!
@SuperCapri23
4 жыл бұрын
I'm interested to see how Alex's car sounds with the h pipe and active exhaust in quiet mode and and track. Early starts and being on call may mean I need to look at an after market active exhaust setup.
@thewideworldofprintingands9021
Жыл бұрын
Just had this happen on my 2019 Bullitt!
@GDaydreams
Жыл бұрын
It's a bit of a pain but my friend has had zero issues after this fix. I hope this video helps in resolving the issue for you 🤙🏾🤙🏾
@MrBluestreak1234
3 жыл бұрын
Crazy ,,,my 17 350R the exhaust valves just today stopped working. Looks like the job would be much easier if you had a lift to work with. Have you ever heard that the actual valve goes bad?
@GDaydreams
3 жыл бұрын
O dang. That sucks! For sure. I ended up putting a concrete slab down and bought a lift haha! I haven't actually but the valves on my GTR with the Armytrix exhaust went bad and had to be cut out, replaced/welded. To be fair, the Mustang ones use an electric motor instead of a vacuum so i don't think the valve will fail. Plus, it's a NA car so unlikely to have a high carbon build up I like the GTR. If I had to put my money somewhere, it would have to be the harness. Best thing to do would be to raise the car and have a good look at the harness. If all checks out, multimeter to ensure power is coming through. If that's all good too, then you know the issue is the motor/pcb or the valve. Keep me posted on how it goes and good luck!
@Spencer50
3 жыл бұрын
I have the same problem the trash wires are exposed and it was rip,;( do i just need to buy a new wires and install it and change the fuse? Would that be all? Do i need to buy both wires left n right when the drivers side wire is fine? And also sir im sorry for the questions, where can i buy the fuse replacement as well? I know nothing about this and dealer is trying to charge me 600$. I appreciate the video sir thank you!! Hope you can help me too 🙏🙏
@GDaydreams
3 жыл бұрын
A new harness as shown in this video shouldn't cost you anymore than 40 to 60 bucks US. You can buy them separately without issue and if you struggle, you may be able to just change it out without having to drop the exhaust. Once done, change the fuse and you are good to go. Don't throw away the harness that is damaged. Repair and keep it incase the same happen to the new one. Wrap some extra heat protection tape like I did so it will increase its lifespan. Have a good look and only replace the damaged harness. Any decent hardware shop will have the fuse. Again, you can see where its located in the video, just take it out and take it with you and they will give you a replacement with a bunch of others for a few bucks. If the harness is visibly damaged and you can see exposed copper wires. It's 100% the same issue. I would recommend you also buy heat reflective tape at the hardware store (O Reilly or Advance autoparts). Let me know if you have anymore questions.
@Spencer50
3 жыл бұрын
@@GDaydreams I appreciate you for the response sir!! Thank you so much, I will let you know if i have more questions. 🙏🙏🙏
@JB-F10-M5
2 жыл бұрын
Next job for the young man is to install your headers 😊😎👊🏽
@GDaydreams
2 жыл бұрын
LOL those tiny hands and arms will get in places I can't.
@Jrslpmx300
Жыл бұрын
What is that part called my car started doing the “Exhaust selection not available”
@GDaydreams
Жыл бұрын
The harness part numbers are in the video. I can't remember them off the top of my head anymore I'm afraid. Both sides are the same part I believe.
@Jrslpmx300
Жыл бұрын
I changed the Harness and fuse and its still giving me the massage?
@GDaydreams
Жыл бұрын
That's strange. Are the motors for the valves operating correctly? Could it be a stuck valve?
@joelmoon9382
28 күн бұрын
Hey did you ever fix the problem I’m dealing with this
Пікірлер: 20