If you wanted to know more about my 26' Tiny House on Wheels, here is the video!
2018 Tumbleweed Tiny House frame
26’ x 8’6”x 13’6”
Double axle single wheel
Clearance and tail lights, road legal with no permits
Exterior:
LP Smartside vertical board and batten, 2 coats Benjamin Moore exterior latex
Cumaru wood accent siding at front door, rain screen clip system
11 Marvin Integrity windows. Have screens
No “Tiny House Tail” utility connections. All utility connections are hidden underneath unit.
All walls are 2x4 wood stud construction with Roxul insulation. R15
Roof assembly is 2x6 wood construction with Roxul insulation, (R21) 1 ½”” polyiso foam on top of sheathing. (R8.7)
Floor assembly is solid foam sheet insulation, with a galvanized sheet metal covering under the frame, and ¾” OSB floor sheeting.
Full peel and stick roof underlayment, 12” black standing seam metal roof and trims. Kynar PVD resin finish, not paint.
Mechanical:
LG Mini Split heat pump. 9,000 BTU Art Cool mirror finish high efficiency 23.5 SEER. Has a high 10,800 BTU heating output. Low ambient heating to -4 F. Heat pump evaporator is mounted centrally for even air distribution. All piping is hidden inside wall and underneath floor. Condensate drain is piped to exit underneath the wheel well, and can be piped externally. Built in WiFi to control via LG SmartThinQ app.
1500 watt electric heater in the bathroom for supplemental and emergency heat. This is a digital thermostat in wall heater, with a quiet fan. All domestic water pipes are in the bathroom, so this heater can help prevent freeze-ups when the weather gets dangerously cold.
All domestic water plumbing is inside the insulated envelope of the bathroom, no piping is in the walls. Uponer expansion PEX piping used exclusively. There is a water shutoff ball valve accessible under the bathroom vanity cabinet. The water inlet for the house is underneath the unit. There is a courtesy 120v outlet under the house to power heat trace tape or heated water supply hose. This house was built for cold winter weather in a variety of locations.
Drain/waste/vent piping is designed to meet most code requirements. The house drain piping is properly vented to a side-wall vent. The shower P-trap is heat traced, and the pvc drain piping underneath is insulated and covered with 18 gauge galvanized metal. The drain exit is left as 3” pvc pipe for your site hook-up to permanent or temporary system.
50 Amp marine style shore power locking twist umbilical located underneath the house.
Everything inside the house is 120V except for the mini-split, which requires 240V.
Interior:
Dual bedroom lofts:
The main loft is 8’x10’ and accessed by storage stairs. This loft features an included King sized luxury foam mattress and high thread count sheets. Two custom wall lighting fixtures and 4 duplex outlets, one also has USB ports for charging. Two windows.
The secondary sleeping loft is accessed via a Birch library ladder. This loft has two windows, two custom wall light fixtures on a dimmer, 3 duplex outlets, one with USB charging. The secondary loft will accommodate a Queen bed, and has a short wall. To prevent falling off the loft.
The library ladder is made from solid Birch with steel fastener accents, and finished in a Bona Naturale finish. This ladder stows out of the way against the far wall, but easily pulls out and slides along a hidden track to a position by the front door.
Storage stairs:
The stairs are built from ¾” Baltic Birch plywood, and have generous tread size and code compliant rise and run. The top step is a double rise/double run configuration to allow comfortable entry between the loft and the stair.
The floor throughout the house is a large format luxury vinyl tile in a dark grey stone pattern.
All interior walls in this tiny house are finished in a ¼” Baltic Birch plywood.
Kitchen:
The cabinets are bespoke, made from ¾” Baltic Birch plywood. The drawers are of a full overlay style, with inlaid black linear pulls. The drawer boxes are a Wurth European metal system with integral full extension slides with soft-close action.
The countertop is ¾” Baltic birch ply, with a doubled edge for a finished top of 1 ½” thickness. It is covered with a Formica laminate. There is a folding table on the right end of the counter that hinges up from the wall and locks in place to form an eating area. There are 2 custom metal and Birch “C” tables that function as stools for the table.
All the appliances, furnishings, are new.
This home weighs approximately 13,300lbs.
The instrument of ownership for this tiny house is via an Illinois vehicle title, which is in my name free and clear of all liens and encumbrances. Bill of sale will be provided.
For sale at:
www.tinyhomebu...
Негізгі бет My custom Tiny House on wheels! Deep dive walkthrough.
No video
Пікірлер: 3