First time builder first time flyer I've been wanting to do this for years so now I'm going to try it
@donbredorouso2787
4 ай бұрын
now this is a real airplane, im watching all the videos and this is well done.
@tomheetderks9997
Жыл бұрын
Nice first build, flies great. With some experience, there's no end to what you can build with adams foam board. I've built a couple of 6S EDF jets. Lately, I've been watching Numa Vig and Julius Perdamo, both you tube channel names. Both are epic builders using depron/xps foam which is nicer than adam's, if you can get it.
@jacksampson7711
Жыл бұрын
Looks good man. I learned to fly scratch building from Flite Test.
@simeonparvanov
Жыл бұрын
Thank you
@juanmolina7959
5 ай бұрын
,uy bueno. Saludos desde Canarias
@jantepas7511
Жыл бұрын
Well done, so much fun with basic stuff. Flying is great in this way. Thanks for sharing.
@simeonparvanov
Жыл бұрын
Thank you
@ra1500
Жыл бұрын
Excellents designs, tank you for to share theres, greetings from mexico.😁
@simeonparvanov
Жыл бұрын
Thank you! Cheers!
@2stevehb
10 ай бұрын
Nice video! Thanks for including the demntions. Been out of rc for a while. I've always have done nitro
@John2009R
Жыл бұрын
I finished my replica of your plane and got to try it this morning. I've never flown anything before so I was prepared for it to be all over in 5 seconds. Well it is actually pretty rugged because I got to launch it about 5 times before it hit a tree and the front skewer got ripped out. I thought it would have plenty of power but it seemed to struggle a bit. It is possible the CG was off. Anyways, it was a lot of fun, even the crashes. Thanks again for sharing your plans.
@simeonparvanov
Жыл бұрын
Thank you. For more power 1406 2500kv motor with a 5.5inch propeller can be used.
@John2009R
Жыл бұрын
@@simeonparvanov Ha! I just discovered I had my throttle curve set to max out at 50%. I had the profile set like that for my "wingless plane" (video on my channel) which had an overly powerful 2212 motor. Looking forward to trying again with full power but we have rainy weather ahead and I have a few repairs to do.
@dirkmarc9523
Жыл бұрын
Welcome to this fantastic hobby, and have luck with all your diy planes.
@simeonparvanov
Жыл бұрын
Thank you.
@ra1500
Жыл бұрын
Están excelentes los diseños, muchas gracias por compartirlos, saludos desde México.😁
@JeremyChung
Жыл бұрын
Dude this is awesome! I'm building a similar plane and posting the video soon. I'm using a lot of the same components but a hot wire cutter for the body.
@simeonparvanov
Жыл бұрын
Sounds great!
@j89dizzle
Жыл бұрын
Cracking little video dude
@simeonparvanov
Жыл бұрын
Thanks
@hasanaydinoncel7437
8 ай бұрын
First of all, thank you for the video. Thank you for your efforts.Is there any problem if we use 3mm foamboard ? If it can be made from 3mm foamboard, should we also change the power and dimensions of the motor and propelle r? What should be the power of the engine and the size of the propeller ? ( I have a 3mm foamboard in my hand. I want to use it, that's why I'm asking.)
@simeonparvanov
8 ай бұрын
You can use a 3 mm foam board for the wing and you can double the side of the fuselage to keep it relatively durable.
@hasanaydinoncel7437
8 ай бұрын
Thank you for your reply.
@ronja_mattis_carlo
8 ай бұрын
Looks really good! Do you share the plans? I just found it in the Video... 😎
@simeonparvanov
8 ай бұрын
Thanks 🙂
@Warpig0321
11 ай бұрын
Looks outstanding. Any plans available? Thanks!
@simeonparvanov
11 ай бұрын
Thank you. You can find all the dimensions in the video.
@user-kx2tt3py2g
4 ай бұрын
i have 2gram servo i can control in wing? 1servo 3,7 gram to control elevator , 2s 300mah battery, 5inch propeller, 12a esc?
@simeonparvanov
4 ай бұрын
That should be OK.
@user-kx2tt3py2g
4 ай бұрын
@@simeonparvanov thank you
@John2009R
Жыл бұрын
Thanks for documenting this. I have started building this as my first RC plane. Questions about the thrust angle: did you just trim the fuselage a bit to get those angles? How did you arrive at those values?
@simeonparvanov
Жыл бұрын
Yes, it isn't easy to be precise at home without proper tools but Trust angles are recommended but not required and can be 0 degrees if that is easier for you. I just trimmed the fuselage a little bit.
@lapajing4788
Жыл бұрын
Super 👍👍👍👍
@simeonparvanov
Жыл бұрын
Thank you
@vancoppenolle11
Жыл бұрын
Nice Bravo
@simeonparvanov
Жыл бұрын
Thank you.
@devbuilds9515
Жыл бұрын
Do you think it would still fly if it used rudder to turn instead of Alirons?
@simeonparvanov
Жыл бұрын
Yes. You can upgrade it to 4 channels and it will still fly.
@himanthbv6003
4 ай бұрын
i am not getting a 1306 motor , so can i use a 11XX or a 14XX motor?
@simeonparvanov
4 ай бұрын
14XX stator size, Motor weighs about 13g should be OK.
@himanthbv6003
4 ай бұрын
thank you
@user-fh4vw2ul5k
Жыл бұрын
la velocidad de el motor es de 400kv o puede ser menor?, ´quizas con la marca de el motor podria encontarla gracias
@simeonparvanov
Жыл бұрын
The motor KV can be less. I used 3100kv or 4000kv both work OK.
@user-fh4vw2ul5k
Жыл бұрын
Perfecto muchas gracias
@2275yogesh
Жыл бұрын
Sir, pls also share details of Radio controller use . 🙏
@heady2008
Жыл бұрын
It's a Flysky radio which is a great starter radio set. I'd go for the Flysky FS-i6 as it's will bind to both their AFHDS and AFHDS 2A radio protocols
@user-fh4vw2ul5k
Жыл бұрын
hola amiga magnifico proyecto, pero tengo problemas con el motor, seria posible que me compartieras la marca del motor, o una imagen, gracias
@simeonparvanov
Жыл бұрын
Any brand will be OK. For example Emax 1306. I used 3100kv or 4000kv both work OK.
@user-fh4vw2ul5k
Жыл бұрын
Perfecto muchas gracias
@himanthbv6003
4 ай бұрын
what is thrust angle and can I use a 2200 MAH battery for the aeroplane
@simeonparvanov
4 ай бұрын
The thrust angle is 2 - 3 degrees. No, you can't use a 2200 MAH battery, the model is too small.
@himanthbv6003
4 ай бұрын
thank you and I mean what is the defination of thrust angle
@simeonparvanov
4 ай бұрын
@@himanthbv6003, you can watch this video from Flight Test kzitem.info/news/bejne/xG-avW2iiHZqaag
@himanthbv6003
4 ай бұрын
thank you
@himanthbv6003
4 ай бұрын
can I use a 2500KV motor instead of a 4000 or 3100KV motor and all of the 400MAH lipo batteries are out of stock , so which one should I use ?
@clintonsmith9931
Жыл бұрын
I do
@schavkin
Жыл бұрын
Why you are limit plane weight by 250g?
@simeonparvanov
Жыл бұрын
In the UK, you do not need to register if you only use a drone or model aircraft weighing below 250g.
@schavkin
Жыл бұрын
@@simeonparvanov Thank you for answer.
@jothimanijsr5313
Жыл бұрын
I want the flight sir
@simeonparvanov
Жыл бұрын
You have lovely birds. I like them.
@GottaKnowJoeHobbies
Жыл бұрын
Hello. I own Gotta know joe's hobbies, welcome to our world. Reach out ill do my best to help you in your journey if you need Joe
@simeonparvanov
Жыл бұрын
Thank you
@coriscotupi
Жыл бұрын
No one builds with balsa wood anymore.
@simeonparvanov
Жыл бұрын
I am currently trying to build my first balsa wood RC plane kit. It is DW Hobby R03 STICK-06 wingspan 58cm
@coriscotupi
Жыл бұрын
@@simeonparvanov You'll love it. Its a great construction material, very repairable, as much as or more than foamies.
@simeonparvanov
Жыл бұрын
Thank you
@colinstace1758
Жыл бұрын
His is foam board, much easier and cheaper than balsa 🙂👍
@coriscotupi
Жыл бұрын
@@colinstace1758 For quick-built, all straight and square models, foamboard is great.
@jothimanijsr5313
Жыл бұрын
I am in tamilnadu india
@simeonparvanov
Жыл бұрын
You can find all the necessary parts to build an RC plane on Amazon.
Пікірлер: 93