Thank you for this. 100 videos on how to replace, but took forever to find a video on what it sounds like. Would make the trial and error replacement parts "adventure" much easier if they all posted the sounds.
@BarboursAutoHelp
3 жыл бұрын
Glad it was helpful
@markdiebel6354
3 жыл бұрын
Plastic hub on mine was smooth on inside ,I dint know it was supposed to have teeth until I seen this video, saved me alot of trouble, thanks....great video
@BarboursAutoHelp
3 жыл бұрын
No problem
@stephanieburroughs3359
Жыл бұрын
We are fixing to change the 2nd set on our Maytag Bravos. We just changed it a few months ago and its stripped again. Your video was very helpful
@brianzeiler4366
Жыл бұрын
I can’t get my drive hub to pull up past the medal spindle the grooves on the spindle sit out farther then the drive hub circle.
@CVEIWKID
26 күн бұрын
The spindle in the agitator probably stayed on the shaft when you pulled the agitator our its supposed to stay up in the agitator @brianzeiler4366
@chrisb7898
Ай бұрын
it's okay to break things while you repair... the key is to tell your wife "I found out this was broken, too'. ;)
@BarboursAutoHelp
Ай бұрын
lol!!
@michaelbyrd1030
3 жыл бұрын
I just changed mine tonight. Thanks for the video as it is always nice to have an idea of what you are up against going in.
@BarboursAutoHelp
3 жыл бұрын
Thanks for sharing
@fayephelps8735
2 жыл бұрын
Thanks Mr obvious. OMG!! Your voice sounded like his from the Bob n Tom show. Thank you for the great info on how to fix my washer!
@BarboursAutoHelp
2 жыл бұрын
Glad the video helped. 😂
@brandonritchie8670
2 жыл бұрын
Very nice, simple video. I think the hub is plastic because it is sacrificial. If it engaged the steel splines then the weak link would be somewhere else in the machine... somewhere harder to get to and a more expensive part.
@steved6043
2 жыл бұрын
Very good point. I’m on my third hub
@lj79762
3 жыл бұрын
Thanks...! Good to know about this... By the way, that small, rounded, plastic cover-cap has a slot on its side for easier removal. Pop it out with a flat-blade screwdriver tip. Then you can see the agitator's mounting bolt head. If your unit has been in service for a good while, you may want to search up ways to pull a tub that has its tub-to-driveshaft coupler stuck to the washer's main drive shaft. I know I'll be applying a small amount of anti-seize compound (automotive anti-seize) to the agitator mounting bolt as well as to the tub's coupler-to-driveshaft splines. This may make life easier for future access and eliminate the hassle of fighting a tub removal. It will also help reduce rust build-up on the agitator's mounting bolt threads.
@MichaelDimaggio-h7x
10 ай бұрын
It is easy to diagnose. Spin the agitator and watch the tub. The tub should be spinning together with the agitator. If the threads are stripped the hub won’t spin together with the agitator. The agitator teeth are plastic also but don’t wear as easily as the hub threads do. If this test shows a problem take out agitator first and go to diagnostics mode and see if sound continues. If it does then remove hub and go back in diagnostics. When sound stops you know what part to replace.
@steved6043
2 жыл бұрын
I agree the inside threads should be metal. I’m on my third basket hub. Good point Brandon
@Dlanoz
3 жыл бұрын
I found the easiest way to get to wash plate off Was to use a shoestring under it . I tied the end of the shoe string together And worked it up
@BarboursAutoHelp
3 жыл бұрын
Thanks for sharing!
@dc5723
4 жыл бұрын
Wow! That sounds normal, just kidding. Our Maytag Bravos made that rumbling sound and it was shaking horrendously during the spin cycle then throw a "UL" code meaning uneven load. This was 2 years ago and we replaced the drive hub and sensor. It purrs now like brand new for a 10 year old washer.
@BarboursAutoHelp
4 жыл бұрын
Good job
@rickeykeeton4770
2 жыл бұрын
Replacing the drive hub solved the shaking noisy spin?? I have one I sort of suspect of causing a little rough spin. Normally, I would expect bad suspension rods, but I got the bounce out of the tub, so I think I might have fixed the rods.
@dannyramirez8428
2 жыл бұрын
We picked it out, because no middle agitator, meant bigger loads. (Blankets). However I think it's what kills these machines earlier than the average washing machine.
@jeffcharbonneau361
11 ай бұрын
I think you nailed it people are over loading the washer
@MrMjrob
2 жыл бұрын
Just replaced my hub recently. Shaft teeth were worn down somewhat, not sure how plastic hub can wear down metal teeth on shaft. Anyway, before I attached new hub, I applied a very light coating of a two-part epoxy on the shaft teeth and then put new hub on. Have to be careful NOT to apply too much, as it will adhere the tub to the part of the shaft where it should freely spin. Working well so far. We'll see how long that lasts.
@BarboursAutoHelp
2 жыл бұрын
Thanks for sharing. That could make it difficult to get back off.
@MrMjrob
11 ай бұрын
@@BarboursAutoHelp it lasted two years exactly. Hub wore out again. Already ordered new one.
@BarboursAutoHelp
11 ай бұрын
@MrMjrob I got rid of mine.
@snivvelslurderagementai2560
2 жыл бұрын
have a leaky issue on this exact model. only had the washer for about 4-5 years. leak happens with oil and water and seems to need entire transmission replaced. part costs half the price of the washer
@melissaakanubby8774
3 жыл бұрын
So when the wash plate comes completely off by itself in the middle of washing is bad? lol
@yashicaprince3741
6 ай бұрын
I also broke my wash plate how did you remove bolt that was still stuck on
@photosbyjf
3 жыл бұрын
same problem and fixed in five minutes once part got herer. Also I could take my hand and spin the wash plate by hand so I newit was this probem. No problems at all taking off wash plate, but it had been removed a little over year ago by service tech
@brianzeiler4366
Жыл бұрын
I can’t get drive hub to pull past the spindles in the rod… any help???
@artslade125
2 жыл бұрын
GOOD VIDEO BUDDY, BUT LETS HOPE THE WIFE DOESNT WATCH IT BECAUSE SHE MAY THINK UR SAYING SHE’S DEMANDING LOL!
@BarboursAutoHelp
2 жыл бұрын
Cat got out of the bag a long time ago. Ain't scared of her....
@richardcrumm5075
11 ай бұрын
Glad you let it run while still not right bc that's exactly the sound mine is making an not ringing the clothes on final spin yeah man ty
@BarboursAutoHelp
11 ай бұрын
No problem
@tira837
2 жыл бұрын
Hi. Can you help? I took the wash plate off. To get to the Hub. I need to replace the hub. I took the 6 screws off the hub but o can’t get the old hub off. The spline shaft is too big. I see in your video there isn’t any spline that your hub is on. The hole in the middle of the old hub is too small.
@MT-gd9mw
3 жыл бұрын
Thank you!
@roverttumbles
3 жыл бұрын
Hello I have a similar washer MVWX655DW0. I'm having a problem with it rattling and shaking when it's on the spin cycle. I'm pretty good at fixing things myself also but I've never fixed a washer. Any views on what my problem may be?
@parkerjones141
2 жыл бұрын
I am trying to replace the drive hub on my Kenmore top loader. The U clip won’t go into the hub. Will the machine work without that u clip in there?
@stevenkerwin4041
Ай бұрын
Use 1" PVC pipe to knock the hub flush, install screws, and insert clip. Your hub is not down all the way. The screws won't pull it tight for some reason.
@michaelwoodward5787
3 жыл бұрын
I used a vise grip clamped vertically right on the center of the agitator plate. Pulled straight up and it came off . Everything else failed.
@soheilarohani1698
2 жыл бұрын
Hello. The circular bowl inside my washing machine is the same model. But after unscrewing the center screw. The inner bowl does not open at all. can you help me??
@stevendeangelis9293
3 жыл бұрын
I replaced this part about a year ago. Now I have to do it again. Are you aware of any other issue that would cause the teeth on the hub to wear prematurely?
@BarboursAutoHelp
3 жыл бұрын
A lot of people are dealing with repeat repairs. Not sure whats causing it other than the part being plastic.
@AAa-yv6pm
3 жыл бұрын
Worn suspension can't spin more than 4 towels, or it will strip. new Suspension is over 100$ ,not gonna happen, so ill use up the 3 hubs I bought on amazon, then buy a new machine!
@JeffreyScottStewart
Жыл бұрын
Get the METAL hub! @@BarboursAutoHelp
@Darton-ok5xt
8 ай бұрын
great vid
@Steve0885
5 ай бұрын
I've been struggling for 3 days trying to get the agitator out. It's a bear!
@BarboursAutoHelp
5 ай бұрын
I will not disagree
@mariaevans3609
2 жыл бұрын
Thank you so much
@vincentpalmero7342
3 жыл бұрын
My bravos wash ok, when it comes to spin, the wash plate spins but not the basket
@JayJay-hm8ru
4 жыл бұрын
So would the agitator would affect the spin cycle.. Because I mean seems like there is rings like on where the plate goes on and then the ones under.. So would the ones under affect the tub I guess? I aam not an applaice person either but I aam just trying to diagnose it my self andd see if I can fix especially in this pandemic the last thing I want is to be goimggg out to the laundry mat. Any tips
@BarboursAutoHelp
4 жыл бұрын
Not sure.
@RickBolt
4 жыл бұрын
Did your repair last? For some reason, my washer keeps stripping out my drive hub, I am getting about a month out of a new drive hub. Thanks for the video.
@BarboursAutoHelp
4 жыл бұрын
I wonder if the spindle that the hub goes on is worn out.
@RickBolt
4 жыл бұрын
Barbour's Auto Help thanks. I think I will give up on this one and part it out. Appreciate the reply.
@BarboursAutoHelp
4 жыл бұрын
I totally understand.
@AAa-yv6pm
3 жыл бұрын
Its because of worn suspension and overloading!
@rickeykeeton4770
2 жыл бұрын
@@AAa-yv6pm I would suspect possible bearing problem.
@lynneturner5847
3 жыл бұрын
we have removed the screw however we cannot get the agitator to lift off. It catches on something. we have tried rotating it left and right but it still catches on something when we try to lift off
@turbonerd42
3 жыл бұрын
I'm right there with you. I was able to get some very small screwdrivers under the lip of the agitator plate. Then by pulling on one of the vanes and hitting near the hub with a rubber mallet, eventually it came off. Still working on the tub removal :/
@turbonerd42
3 жыл бұрын
by the way: block the drain slots around the perimeter or the tub with masking tape or something. The screws that hold the hub will fall down them.
@sarahdelgado7632
4 жыл бұрын
We replaced this part just like you showed but it still won't agitate. It spins and everything else. Any suggestions?
@BarboursAutoHelp
4 жыл бұрын
I don't. Wish I did.
@carlosalbertolinares1242
4 жыл бұрын
Check your motor run capacitor and the drive belt.
@dennismccain1638
4 жыл бұрын
I have a whirlpool and HAD to break wash plate. It was seized on the shaft. Again bad design for a plastic hub on a metal shaft.
@wandaholley8229
3 жыл бұрын
WHAT DO YOU DO, IF YOU CAN'T GET THE AGITAOR OFF?
@BarboursAutoHelp
3 жыл бұрын
Your talking about the part I broke right? I just broke mine. However I have a video linked in the description that may help
@beaandrea9622
3 жыл бұрын
Same problem I am having. We have watched the linked video and still can't get it off. Ugh!
@BarboursAutoHelp
3 жыл бұрын
Sorry 😞. I'm not a pro myself.
@AAa-yv6pm
3 жыл бұрын
Lifted mine out with two 90 degree pics, each 180 apart in the outer holes and lift the whole machine up for s out 12 seconds before agitator comes off, second time I changed the hub, it came off easy.
@brian1715
4 ай бұрын
bro anyone ever tell you that you sound exactly like scott martin!
@BarboursAutoHelp
4 ай бұрын
No. I don’t even know who that is.
@casper1995able
4 жыл бұрын
Pretty sure our washer has the same issue cause it dosent spin like it should,.but we just ordered a brand new washer of course 🙄
@BarboursAutoHelp
4 жыл бұрын
That'll fix the problem for sure!
@casper1995able
4 жыл бұрын
Haha, it was a hand me down and the household that had it before had 3 familys living there so who knows how used and abused it got lol
@victorelias7063
3 жыл бұрын
Where did your get the parts?
@BarboursAutoHelp
3 жыл бұрын
I don't even remember if I got them locally or online....sorry bout that.
@photosbyjf
3 жыл бұрын
amazon, put in the part number that you see on the hub and it will pull up
@akinlolufasanmi516
4 жыл бұрын
Hi I can't fin,d the link in the video you refered to.
@BarboursAutoHelp
4 жыл бұрын
It's in the description of this video. The text just below the video.
@lil2.74
Жыл бұрын
My 5 year old Maytag has done this for the second time. The reason they make it plastic is so you can either pay a repair man or buy a new one. Junk.
@rocky48ish
4 жыл бұрын
I did the samething, I had to destroy it, but nonetheless I got it off.
@BarboursAutoHelp
4 жыл бұрын
As long as it fixed right?
@mr_phamtastic
3 жыл бұрын
your comment about your wife on you is funny
@timstanek5181
3 жыл бұрын
Maytag bravos biggest piece junk mine has gone thru 6 of these hubs Maytag is no help I just keep a spare one on hand to fix last install then this washer going to the curb bought this new broke in1 month parts on the floor it's loud and couldn't be balanced it moves 3 feet sometimes
Пікірлер: 95