There is a problem with previous video, image shake . so Re-upload here. Friends who have watched it can ignore this , sorry~~~~~~~
@OZTutoh
3 жыл бұрын
This is an amazing mod! I'm wondering why the metal tube is much shorter than in your previous mods. Do you get the same fps on all four darts? Does the first dart really shoot because the other three push it out?
@ZDLSPACE
3 жыл бұрын
metal tube i cut correct length for this, i i donot have test machine ,but looks not very obvious diffrent, yes the first one can shot normally,cos the whole lenght longer then 4 darts a little bit ,
@OZTutoh
3 жыл бұрын
Built it and it works! I had not realized that you must lower the gun (or just give it a shake) to load a dart. I was confused for some time. Once I watched tutorials on how an inline 4-shot clip works, I understood. All four darts shoot at about 80 feet per second. Lots of sanding down and filing the parts from the 3D printers, especially the o-ring mount on the dart door slide. If it isn't a firm fit, it will unseal when a dart is fired.
@OZTutoh
2 жыл бұрын
I've searched for a better springer pistol and I honestly think this is the best one. A Rival Knockout inline-4 mod is a close contender because the plunger tube is larger, but without the silencer, this pistol is short and effective. You can stuff it into any cheap drop holster you can buy and have it ready in case your primary jams. I must be getting 100 feet per second on the 1st dart and 120 feet per second on the 2nd to 4th. I'm using a Retaliator 9kg spring. I watched Captain Xavier's BigShock "Can it take a K26?" video and his Spring Removal video to learn how to swap it. The plunger head is well-cushioned. Plumber's thread seal tape is very cheap and you'll need to put a couple of winds of it under the plunger head o-ring to give it a tighter air seal to the plunger tube. I also put as many winds as I could on the thinner diameter section of the 3D-printed inner tube (1:40) so that it can still slide in with a tight fit. I use duct tape on the thicker diameter section to friction-fit it into the BigShock. I used a lot of superglue on the printed ring (1:50) to seal any air leaks with the BigShock. I think I would wrap some thin amounts of threading tape on the printed ring before gluing inside if I did this again. I don't bother putting the handles on (4:50) because the air pressure is too strong from each shot. I keep the dart door held tight against the blaster with my thumb.
@stefanhartanto7939
3 жыл бұрын
This mods look really nice
@ZDLSPACE
3 жыл бұрын
yes,the design very good😁
@JeanIIDeux
Жыл бұрын
Could this not work as a six shot with that suppressor?
@Ribsss0177
7 ай бұрын
can you share the file to the 16mm barrel version of the inner tube like the one you used in the video
@James-vg3fq
3 жыл бұрын
I can’t wait to make my own mod kit
@ZDLSPACE
3 жыл бұрын
just do it😁
@xdlz0154
3 жыл бұрын
多谢分享,这个好漂亮啊~ 请问螺丝应该用什么规格的?
@ZDLSPACE
3 жыл бұрын
谢谢,我忘记了,手上螺丝太多了,好像是普通的m3,希望没记错
@xdlz0154
3 жыл бұрын
@@ZDLSPACE 收到,多谢~
@monkeBeastTitan
2 жыл бұрын
I would buy a printed kit from you, I dont have access to a high quality 3d printer.
@ZDLSPACE
2 жыл бұрын
hi ,i think download 3d file from Thingiverse,then find a local print service is better~
@貓東巴
3 жыл бұрын
感覺最麻煩的莫過於金屬管的部分? 不曉得用塑膠管行不行
@ZDLSPACE
3 жыл бұрын
我猜呀,只要足够光滑的应该可以,之所以放金属管,是因为打印件表面太不光滑啦.
@貓東巴
3 жыл бұрын
@@ZDLSPACE 原來如此,我以為是因為金屬管比較堅固、穩固,塑膠管太軟沒辦法
@ZDLSPACE
3 жыл бұрын
@@貓東巴 哈哈 那里都不受力的,无需太稳固,保证内径正确就可以上.
@貓東巴
3 жыл бұрын
@@ZDLSPACE 了解 謝謝解答
@AzzamSukaMobil
Жыл бұрын
aw man i wish i have a 3d printer :(
@narenthebeesechurgerman422
7 ай бұрын
Whats the barreling material used in this video?
@Ribsss0177
7 ай бұрын
16mm aluminium barrel
@watertakken
Жыл бұрын
I happen to have a mega bigshock and a friend who can help me print.
@MonarchNerf
Жыл бұрын
Could you link the o ring please
@its_spxder7906
2 жыл бұрын
where did you get the big orange muzzle that's shown at 0:30
@ZDLSPACE
2 жыл бұрын
oh ,its the dart zone mk2 muzzle,just fit perfect this one😁
@Darth.E
2 жыл бұрын
Where did you get that sweet silencer?
@ZDLSPACE
2 жыл бұрын
hi, its Worker s product
@christophepinard4661
2 жыл бұрын
bonjour c est quel type le tube que vous mettez dedans merci
@ZDLSPACE
2 жыл бұрын
hi,you mean the metal one? its WORKER stander tube id 13mm,od 16mm
@christophepinard4661
2 жыл бұрын
@@ZDLSPACE thanks you
@okimoto3101
3 жыл бұрын
what fps can i get on this mod?
@ZDLSPACE
3 жыл бұрын
hi, i am not sure bro, but looks almost same as mega transfer to elite directly.
@OZTutoh
3 жыл бұрын
I'm getting 80 - 90 fps with the stock spring
@OZTutoh
2 жыл бұрын
Now getting 100-120fps with a 9kg Retaliator spring and all air-leaks prevented with thread tape.
@Gruener_pokl
3 жыл бұрын
i have printet me this kit but i dont know hoe to put the silencer behind the stopper
@ZDLSPACE
3 жыл бұрын
i have made some change on innner tube,i have 3d file,if u want,let me know ur email,i sent to you😁
can i buy the kit from you? i cant find a local 3d printer :(
@ZDLSPACE
Жыл бұрын
aha you stay in Singapore?
@AzzamSukaMobil
Жыл бұрын
@@ZDLSPACE no i stay at indonesia
@ZDLSPACE
Жыл бұрын
@@AzzamSukaMobil just come back from Bintan😄
@AzzamSukaMobil
Жыл бұрын
@@ZDLSPACE was it nice?
@randomando236
3 жыл бұрын
halllooo
@ZDLSPACE
3 жыл бұрын
😁😁😁ni hao
@randomando236
3 жыл бұрын
@@ZDLSPACE 你好!我的中文进步了 still not very good at the ping ins stuff put I have speaking nailed! 😅😆
@bigbodyboy2193
3 жыл бұрын
I would like to see a mod kit for the strife that doesn’t reduce performance. I can’t find cheap mod kits for the stryfe. This is only a suggestion, you don’t need to do this.
@ZDLSPACE
3 жыл бұрын
i see lots of worker product for stryfe ,plastic and 3d printed. like kriss🤣
@bigbodyboy2193
3 жыл бұрын
@@ZDLSPACE yeah, but they are extremely expensive
@09jeremiah80
3 жыл бұрын
@@bigbodyboy2193I think your best bet is one of those knockoff stryfes or try make on out of cardboard
Пікірлер: 60