check your death wobble here kzitem.info/door/PLO4T4Ez-ZZaTL8_plKzErTaalN0XHuXDg
@drover338
Жыл бұрын
As a owner, most technicians dismissed my requests for them to watch your fix for the "squeeky" axle. They reguarded me as a unknowing person and are just full of themselves in how thing work. I started working and repairing Marmon Harrington AWD trucks before their parents were born. Thank you so very much for your content!
@PowerStrokeTechTalkwARod
Жыл бұрын
🤗🤗
@kayakuprising5914
Жыл бұрын
Don't you just love it when everything comes together like it's supposed to? Good job.
@FlushtheSystem
Жыл бұрын
I wish there was a channel as awesome as this for 6.2L gasers.
@rockie307
6 ай бұрын
6.2 gassers don't have as much trouble
@PowerStrokeTechTalkwARod
6 ай бұрын
Ha! So you think.....
@rockie307
6 ай бұрын
The company I work for has both and the 6.2s have been more reliable small sample but still in my experience the gas trucks have way less issues. Of course it's not typical use idling around muddy construction sites all day and night.
@Engine-town
6 ай бұрын
@@rockie307yeah i’m not surprised by that one bit. I’m pretty sure everyone buying these trucks know that putzing around and idling is for gassers. If you run a diesel like that, the number one issue is the CCV box. Almost no one knows about it, and if they do they still don’t service it. So as a general statement I don’t agree. Like you said they’re being worked a specific way…
@L15a5haw
3 ай бұрын
Buy a 6.7
@matthewgraham7419
Жыл бұрын
Ford needs to give you a big job leading their tech training,you are awsome and getting even better at explaining and demonstrating repair!! Thanks for all you do, you are making a difference in the industry!!
@blackopsrocks
Жыл бұрын
Plow enough snow with these trucks and you can identify exactly what this is within about ten seconds. I sometimes get seals from national that dont have silicone grease in the wiper portion of the seal, if we put them in without checking that they make this noise within one or two plowing sessions. Number two is getting new unit bearings with an ungreased shaft support bearing, that has been happening the last few years so we get stuck doing surgery so we can put a grease needle in that bearing and fill it. I hired a new tech to manage our trucks and machines, these kinds of parts quality issues are so prevalent now its alarming. You will need to be vigilant, that is all it is.
@josephrikalo524
9 ай бұрын
My wife and I have been hearing this on the passenger side of our 2016 6.7 powerstroke. Thanks to you now I know that this can be fixed!! God bless you!!
@MR-si1eq
Жыл бұрын
Love these videos. You make it easy to learn. I'm a torque guy. I need to look and see if things need to be torqued. Then I feel happy.😊
@timsmothers8740
Жыл бұрын
I figured that everything had torque specs, even the lug nuts, should get torqued. Perhaps that's what caused the damage to begin with. I have seen ARod break out his torque wrench in other videos. May everyone find some Easter eggs 🥚 !
@jasonodette1245
7 ай бұрын
I took my 2022 F250 in 4 months ago because of this funny metallic noise also coming from the drivers side axle. I told the dealer I thought something was wrong with the hub. The dealer said their "master tech" said the noises were normal and refused to resolve the issue. I told them there was nothing normal about this noise. Thanks for the video. I'm taking this back to the dealer with a video of my truck making the noise and I'm bringing Ford in on this to make sure whatever is wrong gets fixed.
@PowerStrokeTechTalkwARod
7 ай бұрын
We wish we cld have helped ya
@diggingupnorth3453
8 ай бұрын
My 2022 350 started doing this today and i stopped at the dealership where i bought it. The Service writer came out and listened to it. went back in and talked to a tech that told him it was normal, just a rubber seal rubbing on metal. It sounds EXACTLY like this truck, if not louder. They told me to just keep running it, everything is good.
@PowerStrokeTechTalkwARod
8 ай бұрын
What lyin dumbasses
@neilstgermain
Жыл бұрын
My 2022 has been doing that on the driver’s side. Of course the dealer “can’t replicate” thank you for finding the problem! Now to get them to warranty it…
@matthewcharland8624
4 ай бұрын
2019 f250 with 55k miles. Just started this noise a couple weeks ago now. Very annoying squeal! Great video. Thank you for showing part numbers and describing tool sizes. I’m going to attack this repair myself.
@PistonShack
Жыл бұрын
I couldn't 100% figure out source of the same noise on my f550 4x4 6.0 Powerstroke for quite some time. Thanks a lot for filming this video, it helped me out a lot. Cheers!
@bobk3840
Жыл бұрын
You should use an arbor press to remove the seal on the shaft. Then use the same arbor press to install the new one. I’m surprised that the dealership doesn’t have any.
@pcrengnr1
Жыл бұрын
A pulley puller as well as the arbor press. Not a fan of hammering if I can avoid it.
@californiafarmin2145
8 ай бұрын
This^
@PowerStrokeTechTalkwARod
8 ай бұрын
That's not the procedure to put that part in. You guys see the special tool that's used don't you.................
@shanebowersox4415
Жыл бұрын
Awesome instructional vid! Once again, you made it look easy and saving so many a lot of headaches. 👏🏻
@zachdavis-ev3ih
Жыл бұрын
2022 F550 dump truck, less than 10k miles. Only use 4H in the winter when plowing residential and commercial lots. Noticed the same noise in December brought it to the dealer they stated it was normal. Had a long duration snow storm in January and kept hearing the noise (drove me nuts) captured it on video this time and showed the dealer. They decided to dig a little further this time. Ended up being the same seal. Ford the king of quality the last couple of years. Lol yeah right. I have a love hate relationship with my truck
@landondc4739
Жыл бұрын
“Normal,” and “within spec.” How do dealers stay in business with that bs?
@ken8334
Жыл бұрын
I think Dana makes them.
@nbco55
Жыл бұрын
2011 F350 SRW owner here, I've said the same thing... But my version of the love/hate relationship is that I love to hate it...😂
@bobk3840
Жыл бұрын
@@ken8334 wheel ends are spec’d by the OEM
@robs4517
Жыл бұрын
Do you remember back in the day when axle seals were simple seals and they didn't squeak and come apart like that because they weren't overly complicated? Yeah. That was nice back then.
@GuretoSefirosu
Жыл бұрын
I have been extremely lucky with my trucks (all have been 4x4 except for my 1995 Ranger). I remember the vacuum line leaks causing the nylon/plastic teeth on the F-150's to grind, but my two never did that. My 250 has not had any 4x4 issues to date.
@christophniggli4750
4 ай бұрын
Got a 2017 F-250 410000 km noise just started today Thank you Sir
@cheng7368
Жыл бұрын
Driver side. 21 f350 6.7 had this same issue. Watched over dozens of KZitem videos to see a possible repair for this model year but this is the first video so far for my model year. Was going to tackle myself but dealership got it fixed under warranty. Paid out of pocket to have them replaced the passenger side while they were at it just in case. Also had them install the front axle knuckles seal shield. Hopefully it’ll help keep crap out of the seals. I’ll have to see. A month after the repair now my 4x4 doesn’t engage unless I lock the hub manually. Go figure.😢 But Arod by far is the most knowledgeable person on these super duties. And I really learn and appreciate all your content. Excellent as always
@ajhainstock3997
Жыл бұрын
This just came across my feed, since January I've had about 7 f250-f30s come thru my bay for an annoying squeak all have been a late 2021 to early 2022 production. 6 of them have been for that seal on the axle shaft, one was a rock in the rotor. Must've been a bad batch of seals at the time
@havensoutdoorworld3656
10 ай бұрын
Same issue on same side with 2021 250 tremor 7.3. Very disappointing to see in new trucks. Great video and tutorial! Thank you for taking the time
@PowerStrokeTechTalkwARod
10 ай бұрын
Thanks for coming through and keeping it real
@Mack-Glide
9 ай бұрын
Thanks, My 2022 f350 with 16k miles is making the same noise, except its on the passenger side. Ill be making an appointment at the dealership soon to get it fixed
@mjc250
Жыл бұрын
Had a pile of them doing this lately. Even the installed ones failing a few months later and the same problem. Some no noise but 4x4 inop seal spun like that. I think there was a bad batch of seals. New seals don't seem to last
@oldfarthacks
Жыл бұрын
New, not properly lubed at the factory, a bit of carelessness in assembly, the result, you guessed it.
@Bucs-Fan-James
7 ай бұрын
Very Informative video. As a new first time F250 6.7 owner, I learn a lot from your videos. I like how you go into detail and what to look for when diagnosing a problem. Thank you for taking time to create them.
@PowerStrokeTechTalkwARod
7 ай бұрын
Pppppreciate chu
@asullivan50i
Жыл бұрын
Yes have this problem, not as loud, can only hear it when windows are down! Been waiting for this one, Thanks bro!
@willb7975
Жыл бұрын
That axle C clip. First-time hub replacement on my 06 F350without proper pliers, hours to replace it. Snap-on pliers made it seconds to remove and reinstall...tks arod...
@PowerStrokeTechTalkwARod
Жыл бұрын
I know your pain
@rickcollins1796
Жыл бұрын
Whenever you have one of these apart be sure to grease the axle bearings. The tapered roller wheel bearings are a sealed unit, but on the inside of the hub is a needle bearing the axle rides on that only turns when in 4 wheel drive.
@natey891
Жыл бұрын
That’s a big ass special tool. Hope the seal on my twenty twenty doesn’t fail!
@johnversluis3084
Жыл бұрын
man this would help me when I first seal this design back in the early to mid 2004 when there was no special otc seal installers had old ways struggled
@anthonyc993
Жыл бұрын
Man you are a life saver. My 2020 f250 has been doing this for the past 2 years. I only have 20k miles on my truck.
@PowerStrokeTechTalkwARod
Жыл бұрын
3/36 boyyyyyyy
@airwalkin
Жыл бұрын
My 2020 F350 is making this noise with about 30,000kms. I’ve been waiting months for my dealership to get the parts in to repair this, hopefully this is what they ordered!
@toyoder1
Жыл бұрын
Hallelujah! Thanks Aaron! My 17, 250 just started making that noise this winter. 🤬 I can’t wait to make the repair🤙
@PowerStrokeTechTalkwARod
Жыл бұрын
Easy peasy
@klippelck
Жыл бұрын
There is nothing that you cannot fix. you are always focused On the alumiduty or super duty hands down your a bad ass Mr A-ROD
@PowerStrokeTechTalkwARod
Жыл бұрын
🫶🫶
@bradypayne7623
Жыл бұрын
well said klippelck
@johnm7793
Жыл бұрын
I have a beautiful 2017 F350 with 76k on it. The day of purchase I traded one of the most powerful trucks I’ve owned which was a 20-F250. I noticed before I left the lot the 350 has a ticking noise in the hub, we searched for what sounded like a lug nut rattling in the cover and have yet to find the cause. This video makes me question my service shop… I never get proper answers or concerns. For instance, I dropped the 350 off asking them to service and find any issues. It came back with the same issues that I found myself like a hole drilled in the top of the primary coolant tank and the tank empty the infamous hose clamps loose and leaking across the top of the engine… I’m willing to pay the bill I just would like my truck fixed as it should. Thank you for the excellent videos, info, and work sir! Tell me how to book an appointment for a full service 👏🏻
@PowerStrokeTechTalkwARod
Жыл бұрын
Email me! I got chu. If you become a channel member, there is a DIRECT link to me, PTT in the community posts
@johnm7793
Жыл бұрын
@@PowerStrokeTechTalkwARod email sent sir. Thanks!
@todddubler2091
Жыл бұрын
Ford has used those "rotating seal inside a seal" for a long time. I've never heard the squeal, but they seem to leak a lot more often than just a plain wheel seal. I would think a piece of stamped sheet metal would not make a good sealing surface but admittedly I haven disassembled one to see what the inside is like. There is also a limited lubricant available for the seal which I think contributes to their self destruction.
@tbom1021
Жыл бұрын
Hello ARod , I had a 2015 F-350 Super Duty that had the same issues on both sides as well as the loc-outs needed a pliers to turn them.🤙
@bobklittich5710
Жыл бұрын
It doesn’t make sense that the seal would fail like that. What is the cause? The seal shouldn’t support anything, after all it’s not a bearing right? As I see it, either the u-joint bearings are not keeping the shaft positioned or there is play in the splines going into the hub. A weird one for sure!
@jesseruleman3730
Жыл бұрын
I would like the center shifter, I only own superduty's but drove a friend's f150 I liked it. I don't need six cup holders in the front.
@ajmcdonald7906
5 ай бұрын
My tuck has been doing this. Glad to find this video from the best content creator. Now I’m gonna watch the video and see what you say!
@PowerStrokeTechTalkwARod
5 ай бұрын
Thanks pal
@jod329
Жыл бұрын
2017 F350 has made that noise since new. Replaced bearings and seals under warranty and still the same issue.
@ditchpicklefishing5661
Жыл бұрын
My 17 250 with 55k had a similar failure, minus the noise. My seal was failing to keep vacuum. It was actually putting the lock out in a bind over time. This would engage the lock out regardless of it is was locked in or not. Wheel bearing was fine.
@frankjcondon3809
Жыл бұрын
2020 F350 been making that noise for 20k just had the seal replaced. I smell recall. maybe LOL. just inferior parts being used past 3 plus years.
@user-ri6hl3xe4y
8 ай бұрын
My 2021 F250 does this. Thanks for doing this video. It was well done!
@PowerStrokeTechTalkwARod
8 ай бұрын
Thank you I appreciate that I worked hard on it
@nathanstaab
Жыл бұрын
They sure haven’t changed those seals much since 1999.. that is a nice tool, always used a 1.5” piece of threaded pipe and pipe flange to set that seal on both the axle and in the housing
@patriciareynolds2729
7 ай бұрын
the cheaper seal is too flimsy to drive on with pipe flange without maching lip onto pipe flange!
@whosaidthat5236
Жыл бұрын
Lol that intro the noise from the wheel was making my dog freak out
@Belangerfamilyfun
Жыл бұрын
My truck started doing this over the winter so thanks for the fix. A question about another issue, the 4x4 won’t engage in cold weather ( minus 20 or colder) I am told this is not unusual in cold weather, help!
@PowerStrokeTechTalkwARod
Жыл бұрын
It should be going into 4x4 REGARDLESS of the temp outside
@Belangerfamilyfun
Жыл бұрын
@@PowerStrokeTechTalkwARod exactly what I thought, I hate to say it but because I’m a female they often take advantage
@rockyroad9709
Жыл бұрын
THANK YOU 2012 f 450 6.7 i noticed the SAME sound only in the morning when i turned the steering wheel almost full lock to the right, It dont do it no more, seemed to quit on its own BUT if i hear it again ill know. ( I torque EVA-THANG bearing nuts on back side of knuckle, caliper bracket fasteners, lug nuts etc.,) Thanks again
@davestewart9146
Жыл бұрын
On my 06 superduty I need to replace the axle tube dust seals, I need to order the tool and seal kit you used, great video sir
@PowerStrokeTechTalkwARod
Жыл бұрын
Thanks brotha
@marcsheldon6512
Жыл бұрын
Don't forget the c clip tool! Standard ones won't work. Need the big beefy one....
@sammpofu9265
Жыл бұрын
I do fleet with 100 super duties I sometimes change them at 20 000 km thanks Ford for keeping us busy
@McCallieOrchestra
Жыл бұрын
Great video! I have a 2002 Excursion with 2006 axles and the driver's side makes a similar, loud squeal once every turn but only at slow speeds. Started after a shop installed a new lockout hub. I'm hoping it is just a bent dust shield and have not dealt with it in almost a year and a half. The front axle also makes a loud clunking noise and has movement where the driveshaft goes into the pumpkin so that is a higher priority to fix. If the squeal isn't external, now I know what to suspect. Also, I am jealous, I don't think I ever worked on a vehicle this new or clean.
@freethinkingamerican80
Жыл бұрын
Had the same exact issue, had the dealer replace them last December
@brentyuers8963
5 ай бұрын
My dealer can’t even fix my cruise control on 30,000 klms f350. They will surely be stumped and claim no warranty for this as they do with everything else. I hate dealerships after you own your ride.
@TheLoner801
8 ай бұрын
I just had to use the 4 wheel drive on my new to me 2019 F350 deisel dually. At speeds more than maneuvering around the driveway, i am hearing a faint screech / squeal. Only in 4x4. Gonna be looking into it soon.
@PowerStrokeTechTalkwARod
8 ай бұрын
Bet thats it
@firemedic2572
Жыл бұрын
My 22 with 12k miles same thing. I will forward this video to the dealer.
@PowerStrokeTechTalkwARod
Жыл бұрын
Yes sirrrr
@russelldejetley
Жыл бұрын
I have a 2022 F450 and believe it started making this noise, or I just noticed it since the window was down. Wasn't as loud as this but same area. I'll need to research this further. Thanks for the tip!
@joshuanickerson1108
Жыл бұрын
I had a rock stuck in between the rotor and backing plate made the same noise. Lol took for ever to figure it out
@Chubby672
Жыл бұрын
When setting the seal stub shaft, I just use a press and some old bearing races and use the hub to set the seal in the knuckle. Don’t have fancy tools 🥹
@PowerStrokeTechTalkwARod
Жыл бұрын
Was 89 bucks from OTC worth every penny
@DavidVanHelden1
Ай бұрын
I have the noise in my 2017 F350.... already bought the new tool and seals to fix the problem
@roadglide1142
Жыл бұрын
Amazing how soon that seal failed 😮
@davebane1865
Жыл бұрын
exactly the same noise on my '22 F250 Tremor... 22k miles
@PNWTRUCKER92
9 ай бұрын
I have a 21 f350 making the same exact noise from driver side I'm sure it's the same issue
@michaelbefumo-qg7ji
Жыл бұрын
I got a truck wasn't 25 years old LOL if those parts would be seized on there. Seems like it came apart like butter good work
@Mr.J345
Жыл бұрын
Good to know what it is now, mine makes the same noise with 5k
@wayneo7220
2 ай бұрын
This video made my day. I have a 2010 F250 with the same noise, but mine just make noise after backing out of my driveway, turning right and starts making the metallic rubbing noise for about 200' then stops. Being in 4WD doesn't really make a difference. I had it in the shop and was sure it was a hub bearing, but the mechanic wasn't sure and didn't make any promises that a new hub was the cure. Sure enough I dropped $1000 on the job but it didn't fix the problem. Now I'm thinking he knew but didn't have the seal installer tool. My speedometer and odometer stopped working a few months ago, just before the squeaking started, and now I wonder if it could have been related to the speed sensor and this bad seal? What do you think? Thanks again for this video.
@PowerStrokeTechTalkwARod
2 ай бұрын
No it's not related
@patriciareynolds2729
7 ай бұрын
ED, had to grind tips of my cclip pliers to work! why not pull pull/push axle into assembly with 4 rear nuts as i did?? didnt buy special driver tool, you hit hard with 2lb hammer! the cheaper seal wont take much hammering! the snap ring was frustating with my harbor freight pliers! u do have nice clear videos.
@AonGuardian
Жыл бұрын
Sounds like an ominous banshee approaching 😂
@matthewpernat3088
Жыл бұрын
My brothers 22 was the seal, my 22 they changed the u joint, interesting as I always greased it, toom care of the noise though.
@bradwlyon
11 ай бұрын
I have a 2022 F-350 Platinum 6.7 with just 15,000 miles on it. I’m 1,800 miles from home on vacation in Yellowstone, and it’s making this noise in both 2 and 4 wheel drive.
@mikeleblanc1555
Жыл бұрын
I have a 2021 250 7.3 tremor front driver side has squealed from day one
@mariobrothers8348
Жыл бұрын
Wish I had that wacking tool when I did mine. I also changed the axel shaft tube seal while I was in there.
@ricka5471
Жыл бұрын
Great diag. I might have suggested the right side to be replaced also. I have a feeling it might be back in soon for the right side. Thanks for showing us this and have yourself A Great Day.
@PowerStrokeTechTalkwARod
Жыл бұрын
Thanks buddy I really appreciate it. However I can only replace What's broken when it's under warranty I can't just preemptively replace the right side
@electrake2063
Жыл бұрын
Mine has never had this problem. Oh, that,s right, I don't have a vacuum seal for my vacuum controlled hub on my 2003 Dodge 4x4, I added manual lockouts from Yukon and they work great all the time. What a messed up system Ford put into their hubs. These things don't work whenever you need them, and you don't find out until you need them you need to go out and manually lock them anyway!
@mpmagnussen
Жыл бұрын
Every super duty I've owned the past 15 years has had this problem. To add insult to injury what they don't tell you is when you live in the northeast this is basically a service part that has to be taken apart and replaced or cleaned or checked every year with the salt and rust and corrosion and yet still the 4wd system fails and needs manual locking
@tubewaldo
Жыл бұрын
Very good vid. I perfer pre 1998 Dana 60s w serviceable wheel bearings,
@Leebetter
Жыл бұрын
Agreed. Those were easier to repair, as goes for the Dana 50s of the era.
@tomday8352
Жыл бұрын
REEEEEE! you get a Rainman Ray reeee as I did not see any manual "clicks"
@hphillips7425
Жыл бұрын
Good video. Explained well. What is the cost for one not under warranty?
@saleen4399
Жыл бұрын
I am curious on this as well. I have the noise. Can here it at a slow roll not even when my 4x4 is engaged.
@user-dq3jk9py4q
6 ай бұрын
Yeah, how much?
@PCGonline
Жыл бұрын
i could hear mine when i was out plowing in residentials neighborhoods. seemed like it went away at higher speeds but 5mph it was most prominent. it went away about mid season
@lont.4507
Жыл бұрын
The metal ring is a depth gauge/spacer. It’s only used on newer trucks. My 2015 did not require its use. Sorry I don’t know the year it started being required. The tool came with the information but I tossed it.
@PowerStrokeTechTalkwARod
Жыл бұрын
Its to install the seal into these hubs m. All the trucks
@bobbylarotonda5674
Жыл бұрын
Awesome helpful video , thank you for sharing your time.
@Alignmentguy
Жыл бұрын
That is the sound of the needle bearings turning to powder…
@brentedwards2606
7 ай бұрын
Wheel speed picked up with the new parts
@Gibsonchha
Жыл бұрын
So professional
@gilmerturner5862
5 ай бұрын
I have a 2021 F250 and the passenger front is making this noise while in 4H. I will take it to the dealership to get it fixed.
@eduardocampos2214
Жыл бұрын
I have a clicking noise coming out of my front passenger side tire, I took it to the dealer and they told me I have to replace the transfer case even though the noise clearly comes out of the hub 🤦🏻♂️
@terrytinagero777
Жыл бұрын
Sounds like a rock stuck to the rotor
@christophercharron7997
Жыл бұрын
Mine does the same thing on the drivers side with the hubs locked but 2wd.
@Mr42960
Жыл бұрын
The round metal shim they give you to use against the drive tool stays in or comes out after the seal is installed? I guess that seal is also responsible for holding the vacuum? Can't remember if vacuum locks or unlocks the hub on the superduty, I think Ford went from one method to the other.
@evictioncarpentry2628
Жыл бұрын
Vacuum holds the hubs open (2wd) shifting to 4x4 releases vac. That's why when you have a vac leak sometimes the hubs are trying to half engage and make a grinding sound. The metal ring is for install only so you don't hammer the seal with the install tool.
@lont.4507
Жыл бұрын
I just replaced u joint, all the same process though. Mine is 2015 and I believe that the metal ring is a depth spacer only used for the newer trucks. My 15 didn’t require it. Sorry I DONT recall the cut off year.
@PowerStrokeTechTalkwARod
Жыл бұрын
Your description is for the F150s the Superdurys need vacuum to GI INTO 4x4. Go explanation tho
@evictioncarpentry2628
Жыл бұрын
@@PowerStrokeTechTalkwARod Got it. I only have a small fleet of F150s and I assume they SDs operated the same way. The IWE vacuum hubs are the biggest pieces of crap ever. Ever single person I know with them has had at least one fail if not multiples or yearly.
@PowerStrokeTechTalkwARod
Жыл бұрын
I know. We started plugging off the vacuum ports. There is a TSB on it.
@user-qt3js3yx7u
Жыл бұрын
Yeah, I have the same noise on a 2022 f350 gasser with 15k miles. Seems to be a 4x4 vacuum line issue as well at cold temps (well below zero).
@blackopsrocks
Жыл бұрын
I have another suggestion for people who use this trucks for snow and ice service. SILICONE SPRAY the area around that seal after brake clean and wipe as often as you care to do it. That will help prevent brine and snow from getting into that area, sticking to things and melting into that seal. Doubles the life for our stuff, otherwise we used to do u joints, seals and hub lockouts every two years.
@brucedeleskey8540
6 ай бұрын
Yes I'm a victim 2021 46.000 miles on it
@TheCOM
Жыл бұрын
Nice job A-rod. You the Man!
@ddznoche
Жыл бұрын
Great video! What was the reason for replacement with such few miles.
@07glide5
Жыл бұрын
Great education!! 👍
@juansebastianlopez8828
8 ай бұрын
Thanks for the video. I just replaced my upper and lower ball joints on both sides in my 2010, so I obviously had to do ALL of that and more while replacing them. I wish I would have seen your video first 😅. Quick question, when I re-installed the shaft, it went in easily, but I didn't get the other wheel to turn, did I do something wrong? I haven't had any issues while driving it. Also I put it on 4x4 but I don't know how to actually test it without putting it up in the air 😂. Thanks in advance.
@firstlast---
Жыл бұрын
You work in a beautiful facility
@PowerStrokeTechTalkwARod
Жыл бұрын
Yes😍😍😍😍😍😍😍😍
@lifeaccordingtobri
Жыл бұрын
sounds like a bag of roosters crowing LOL
@rjr4084
Жыл бұрын
I had this same noise, except the passenger side and not nearly as loud, on my 2022 F250 Tremor. I took it to the dealer and they diagnosed it as a bad hub bearing. They replaced the hub assembly under warranty, problem solved.
@dannermanner5506
Жыл бұрын
Lol. Why did the u-joint seem off centered after everything was put back together when it was spinning.
Пікірлер: 352