Ayo tankss! Without your video I won't have finished at 5 pm !🤝
@chrisrose6541
4 жыл бұрын
My granddad was having an issue getting the time bar back into place and I found the video and loosening the bolts as you suggested on all the tine bars worked perfectly! Thanks for the video.
@mikethejoatmon8287
4 жыл бұрын
Thank you for watching and for the the comment, glad you found it useful. Thank you too for helping your Granddad!!!
@epicjag3365
Жыл бұрын
Thanks for putting this up here it was exactly what we needed for my dad to fix it and no blow himself up, thank!
@WeathermonTaxidermy
2 жыл бұрын
Very helpful. My husband is replacing bearings and was having a difficult time with getting the tine bar back in.
@mikethejoatmon8287
2 жыл бұрын
Thanks for watching and the comment. Glad the video was helpful.
@shadyoakssawmill7754
2 жыл бұрын
I have been working on my New Holland 258 Rake replacing tine bar bearings and just started to reinstall the bar and was having difficulty getting it lined up so instead of fighting it I watched this video and was able to reinstall the bar in a matter of minutes your video is a home run thanks for the knowledge I will pass this on.
@mikethejoatmon8287
2 жыл бұрын
Glad the video was helpful. Thanks for the comment!
@davidrobertson376
3 жыл бұрын
I am glad I have watched this as I have 2 rakes to go through. very helpful information
@mikethejoatmon8287
3 жыл бұрын
Thanks for the comment! Glad video is helpful. Check out my other videos on 256 rake repairs.
@hartshomesteadaustralia3837
Жыл бұрын
Your a life saver I just brought one of these from a friend and have to replace one of the tine bars tried every to line it up until I watched your video so I’m gonna give it a go tomorrow the tine bars have a flat head on the end of the thread so getting the bolts of is gong to be tricky but I give it a go
@mikethejoatmon8287
Жыл бұрын
Thanks for watching and the comments from down under! Hope the video helps, tine bars can be a pain sometimes. Let us know how you made out repairing your rake.
@hartshomesteadaustralia3837
Жыл бұрын
@@mikethejoatmon8287 will do definitely a quick question when I undone the 5 bolts on the drive shaft side oil came out is that normal
@mikethejoatmon8287
Жыл бұрын
@@hartshomesteadaustralia3837 Shouldn't be any oil. Sounds like bottom seal on the gearbox is leaking oil, possibly from a bad bearing in the gearbox or just a bad seal. Check out my video on the gearbox repair for New Holland 256 rake. I show seal and bearing numbers you need to rebuild it. Good luck with your repair!
@lorinjones9082
5 жыл бұрын
I couldn't get everything loosened up like you did (without a torch), but enough of them to give it a little play. The best trick was using the long punch in the hex hole to pry it into place. Thanks for the videos.
@mikethejoatmon8287
5 жыл бұрын
Glad you found video helpful. Thanks for watching and the comments. I try to post useful information to KZitem and I use what others post too.
@localcrew
3 жыл бұрын
Very helpful video for me cause my friend has one like this (258) and it needs lots of work. Good thing he got it cheap! I just subscribed!
@jefflogical774
4 жыл бұрын
Thanks, this has been very helpful.
@user-zq9kj1tj8o
Ай бұрын
Thank you so much!!
@davidphilpott6606
2 жыл бұрын
Thank you!! I was pulling my hair out, and there's not much of that.
@mikethejoatmon8287
2 жыл бұрын
Thanks for watching and the comment! Glad the video helped. Don't want people pulling their hair out, may need it for the colder months.⛄ 😀
@landontesar3070
4 жыл бұрын
Thanks for the video. Always good to know what you're getting into, esp the use of the punch. I did not see replacing the bearing, I suppose it is straightforward.
@mikethejoatmon8287
4 жыл бұрын
Landon, thanks for watching and the comments. I did do a video on tine bar bearings: New Holland 256 Tine Bar Bearing Puller.
@kylejohnson4136
Жыл бұрын
So are the bearings not sealed? I'm changing the bearings on my 256 tine bars and had the same idea about the grease fittings...just curious if the grease will come through the bearings if they are sealed bearings. Thanks.
@mikethejoatmon8287
Жыл бұрын
Kyle, thanks for the question. The factory bearings are sealed on both sides. If you are going to add a grease fitting to the tine bar bearing housings, just pop out the bearing seal that would go into the bearing housing first. A small flat screw driver inserted between the seal and the bearings inner race works well for this. Leave the seal in the bearings that are going to be on the snap ring side. Thanks for watching and good luck with repairs.
@user-zq9kj1tj8o
Ай бұрын
Where do you get your bearings?
@mikethejoatmon8287
Ай бұрын
If it's just the bearing and not the whole assembly you want, Amazon is a good place to start. If it's the whole bearing/stud assembly, I will have to go back and look. Just let me know. Thanks for watching!!!
Пікірлер: 27