We had a repairing video about how to fix the problem of Face ID set up failure by grinding the metal shield on the Face ID module before, but some fans left comments that grinding method would leave obvious traces on Face ID module, which is not good for repair shop recycling. Now we will solve this problem by using hot air gun and updated JC V1S machine.
@now6942
3 жыл бұрын
Hi Dear, nice Video Thanks! i have a question, i have a this same problem (upper / lower) but after DOT test i get S,B,D,A abnormal but rest ist normal ( ICC, NTC ) what is the problem? and in dont see "Results" or "FUSED" message. Thank you so much
@Elekworld
3 жыл бұрын
@@now6942 Hi, probably the power suply diode has been short-circuited, need use tin wire to connect it again. Pls check video from 2:35, connect it and test again.
@Faiz_k_fk
3 жыл бұрын
@@Elekworld my iphone x showing Face ID not available
@Faiz_k_fk
3 жыл бұрын
@@Elekworld and also not showing True Tone feature...
@Elekworld
3 жыл бұрын
@@Faiz_k_fk Face ID not working, depends on many possibilities on front camera module: Dot projector, Infrared Camera Flex, Flood illuminator etc, so we suggest you go to local shop and check what's the exact problem then fix it. And for true tone problem, probably your screen isn't genuine, or the new screen wasn't copy&write genuine true tone data from old screen. Hope it helps.
@ahtshammughal2890
2 жыл бұрын
Excellent work Good for new user of Jc v1s as i am ❤️
@Elekworld
2 жыл бұрын
Thanks bro, pls stay tuned with us for more update. :-)
@doriongarcia8887
3 жыл бұрын
Good vid as always I thought this would have been a simple repair like the True Tone , where you would copy and paste the data
@Elekworld
3 жыл бұрын
Face ID problem is more complicated and more important than true tone, because it's about privacy and financial safety. But JC V1S launched the new dot projector board and upgraded its software, which make it easier to repair.
@BillAnt
3 жыл бұрын
I've been doing board level repair for almost 20 years, but this one looks more complicated than brain surgery with so many things could go wrong. Yikes! lol Oh and fuq Apple!
@Elekworld
3 жыл бұрын
@Bill A Vivid metaphor! Maybe we need thanks Apple for bring all repairmans' skill going up to higher level.😂
@BillAnt
3 жыл бұрын
@@Elekworld - Sure, anything is possible given enough time and money spent. Unfortunately in certain countries you simply can't charge the customer enough to pay your techs doing a couple of hours of highly skilled jobs. :( It all comes down to a cost/benefit ratio. Apple has got us by our balls (as a metaphor lol).
@Elekworld
3 жыл бұрын
@@BillAnt lol, easier to understand your feeling with metaphor. Anyway, we can tell the repair price before customer decide to fix the problem or not, then maybe it's easier decision for both customer and us.
@ceejay_gaming9636
2 жыл бұрын
Wow I didn’t know it was possible to do all of this with the JCVS1 I was about to buy the I2C face Id repair kit
@Elekworld
2 жыл бұрын
Yes, JC V1S is one of the best programmer that is very helpful and powerful.
@ahmedp3
Жыл бұрын
Hello Sir, thanks for this amazing help i have an issue with my Face id on iPhone X the problem is it keeps saying (move your head a little higher/ position your face inside the square) but nothing happens after i checked the 2 dots and they are there and working, i checked the flood illuminator by calling and the screen went black which means it's also working, i checked the portrait for the front camera and it also worked, everything in the phone works perfectly, but i should mention that the Display is Damaged and contains a green lines from the left side, could that be a reason for why the face id isn't working, or just my face id died and that's it?
@Elekworld
Жыл бұрын
The display screen have nothing to do with Face ID, so probably the dot projector or the sensor flex were damaged.
@ahmedp3
Жыл бұрын
@@Elekworld oh, thanks for the reply, but i would like to add that i replaced the screen and in the process i noticed that some dust got into the phone on the face id components and everywhere so i gave it a little bit of cleaning, and Face ID works again
@Elekworld
Жыл бұрын
@@ahmedp3 Great update ,bro, thanks for sharing.
@quadraquadra8838
3 жыл бұрын
Hello, what a nice and helpful video you guys did here... I bought the machine and did the same as you guys did, but there is a problem is that when i add my face, and lock the phone it won't open to my face. So let me be clear... The thing is that at the beginnning it was giving a warning to get the phone lower and upper. right now everything looks great. Just that when i put my face and it says everything is complete . My face id restarts directly. So please if someone can help me with this or anything because i've tried several times. Thank you so much and i appreciate your help.
@Elekworld
3 жыл бұрын
Dear friend, we can't exactly know what's the problem by "Face ID restart", so if possible maybe we can contact with skype: sales-elekworld to send a video showing the problem, then we might can be helpful.
@zodcybercontactthemoninsta3184
3 жыл бұрын
I'll recommend Gacktech on Instagram to you.. He's very fast and reliable
@quadraquadra8838
3 жыл бұрын
@@Elekworld how can i contact with you on skype and send you the video ?
@Elekworld
3 жыл бұрын
@@quadraquadra8838 add me with Skype ID: sales-elekworld
@Eluqui7
3 жыл бұрын
Good video. is it possible to use a healthy face id original module and program it with the one that is defective?
@Elekworld
3 жыл бұрын
No, it won't work, because data can't be burn in it by 3rd party except Apple itself, it wasn't designed for this. Have to use JC blank dot projector flex and its device.
@steve333
3 жыл бұрын
Why bridge the connection on the fuse instead of replacing it with a non-blown fuse?
@Elekworld
3 жыл бұрын
Many reasons: 1- A tin wire has same function, 2- there isn't extra fuse to buy and use; 3- same cost and safe enough.
@InfoReserves881
3 жыл бұрын
Nice One
@Elekworld
3 жыл бұрын
Thanks, Rana. If you like our video, pls sub for more helpful video update. ☺️
@pow9606
3 жыл бұрын
Skills
@Elekworld
3 жыл бұрын
Thanks friend.
@hardwaresolutions0702
2 жыл бұрын
True depth sensor failed
@pacmaninfinity4015
3 жыл бұрын
Amazing!!!
@Elekworld
3 жыл бұрын
Thx for comment, if you like our video pls sub us and stay tuend for more helpful update. 😊
@pacmaninfinity4015
3 жыл бұрын
@@Elekworld I've subscribed instantly. But I have a small request. I really want to know how the JC VS1 Programmer works and how I am able to use it to its full potential. Can you make a video explaining everything about the JC VS1. Love your content!!!
@Elekworld
3 жыл бұрын
@@pacmaninfinity4015 Yes, actually we have made this video 1 year ago, check this: kzitem.info/news/bejne/z22QxWGdaqNhg5g. However, bcuz JC tools is always keep upgrading, so please stay tuned with our video update, we might use JC V1S and upgraded board&function to repair more phones.
@pacmaninfinity4015
3 жыл бұрын
@@Elekworld Perfect!!! Thank you. I really love what you are doing. I my self bought the JC VS1 and I wanted to fix a phone I owned. I'm not a professional but I do have a passion in repairing phones and other devices. I'd love to learn more from you and this channel in the future.
@Elekworld
3 жыл бұрын
@@pacmaninfinity4015 You are so welcomed, friend. Actually we will launch more and more tech videos in future, I beileve it will helps a lot.
@faisalagung420
20 күн бұрын
xr support?
@davinder_sasan
3 жыл бұрын
What will be cost for repair
@Elekworld
3 жыл бұрын
If you have all other repair tools, you need just JC V1S programmer with truetone board + extra Dot projector board, totally about $63. For any other questions and exclusive service, please contact service@elekworld.com. :-)
@davinder_sasan
3 жыл бұрын
@@Elekworld bro i dont even know ABCD about repair ☹️
@Elekworld
3 жыл бұрын
@@davinder_sasan If so we suggest you go to local repair shop for the help bro.
@davinder_sasan
3 жыл бұрын
@@Elekworld my mobile in warranty but its water damage bcoz i swim with my iPhone 11 Pro After that my face id stop working But i was ok till now it happened before 20 days But from yesterday i have one new from I don’t its come after the new update or else My right side screen from corner not working properly like it difficult to press (p) button Full Vertical line from Top to lower screen do u have any idea about the problem
@davinder_sasan
3 жыл бұрын
@@Elekworld some time its working sometimes not
@thisisben7411
3 жыл бұрын
I have a question please , i changed my iphone X batterie by another and i copied data from the old battery to the new battery but in settings it shows service . I did changed sn again with icopy in program on pc , i fixed it it shows the capacity but after few days the battery health shows service again in settings????? What should i do ?
@Elekworld
3 жыл бұрын
Hey, the best method to remove both battery warning message and show battery capacity is like below two videos: kzitem.info/news/bejne/oo2vsniHgqd6dYo with Qianli tool, and kzitem.info/news/bejne/0m2VrYCag2iApqQ with JC tools.
@thisisben7411
3 жыл бұрын
@Elekworld i have iphone X normal not xs or xr. I dont have battery message warning. I Have service and( - - ) in battery health in settings after copying Sn from old battery. Because the JC did not copy just the SN it did copy the battery health status from the old battery also , how to fix this please .
@Elekworld
3 жыл бұрын
@@thisisben7411 I wonder if your new battery is original quality or not please? Technicians said this works on original quality battery and stable, but aftermarket quality might unstable.
@thisisben7411
3 жыл бұрын
@@Elekworld original 100% i took it from a broken iphone x and the jcid also say its original . Do you have any solution that i can try
@milkyspray2436
3 жыл бұрын
Where can I buy the dot projector test board
@Elekworld
3 жыл бұрын
Please check this link and login to see price: www.elekworld.com/Shop/productinfo.aspx?proid=13658&categoryid=289. Also you can email service@elekworld.com to get exclusive 1 on 1 service.
@mashalrangin7368
3 жыл бұрын
Where is the shop?
@Elekworld
3 жыл бұрын
Please goes to link below and register to see price: www.elekworld.com/shop/productinfo.aspx?proid=12539&categoryid=287, or contact service@elekworld.com for exclusive service.
@mdmujahidali-t5e
Жыл бұрын
Hi
@gulzaibkhan1825
3 жыл бұрын
I have jcid also the extension of face id...but its not showing like u menu...do i need to update the firmware
@Elekworld
3 жыл бұрын
Yes, make sure that two things have been settled. First, make sure your JCID V1S has been upgraded with the dot projector repair software. Second, make sure you have the new Dot project testing board.
@valentinopaco
3 жыл бұрын
Why it is necessary to remove and scaffold the mosfet thank
@Elekworld
3 жыл бұрын
@@valentinopaco The mosfet was short circuited so we have to make it again. And, the mosfet is bundled with iPhone one by one, you must use the genuine mosfet to resume the Dot project function.
@zodcybercontactthemoninsta3184
3 жыл бұрын
@@valentinopaco I'll recommend Gacktech on Instagram to you.. He's very fast and reliable
@nelsonudeh4473
3 жыл бұрын
Please how can I send my phone to you guys for Face ID repair?
@Elekworld
3 жыл бұрын
Bro, considering all the risk and cost during export&important customs clearance, sipping cost, shiping time, privicy&financial safety, we suggest you find a professional local repair shop to fix it. We might launch repair course in future, if you're interested in this, pls sub our channel and stay tuned for update, bro.
@thedarknesscrazy1200
3 жыл бұрын
I can’t write data on another dot matrix ☹️ I have 2 dot matrix for xs max one of them fused the 2nd one perfect but when i try to write the data the device say that its impossible to verify dot matrix material and burning! failed
@Elekworld
3 жыл бұрын
The key point is that you have to use JC's Blank dot projector flex instead of original dot projector, because it can't be writing and burning data.
@thedarknesscrazy1200
3 жыл бұрын
@@Elekworld Is it a read only or whats the problem ??? Bcz i have the v1s with its dot matrix board And i have 2 front camera assembly
@Elekworld
3 жыл бұрын
@@thedarknesscrazy1200 You need below items to complete the fix: JC V1S+Dot matrix board(You already have) + JC Blank dot projector flex(Check video 1:29).
@thedarknesscrazy1200
3 жыл бұрын
@@Elekworld Thats hard bro 😩 Its gonna take alot of time and work and in the end it might not work and i have to do it again and again 😩
@Elekworld
3 жыл бұрын
@@thedarknesscrazy1200 Yes, professional skill required and time consuming. Compared with recover Face ID, I still think it's deserves.
@milkyspray2436
3 жыл бұрын
I’ve got the board how do I update my jcv1s to do this as when I plug in the board nothing comes up even when I connect the dot projector
@divanshunandananda3500
3 жыл бұрын
i am having same problem
@Elekworld
3 жыл бұрын
Please goes to below weblink and download JC repair platform, register and login, then connect V1S with computer, and click "Repair Fitting" to find the upgrade option: www.jcprogrammer.com/download-center
@danpwa2659
3 жыл бұрын
can you help me broo
@Elekworld
3 жыл бұрын
yea, what can we do for you?
@danpwa2659
3 жыл бұрын
@@Elekworld can you repair my faceid
@Elekworld
3 жыл бұрын
@@danpwa2659 It depends on what's the problem of the face ID. Please contact service@elekworld.com for more help.
@mohitdubey4168
2 жыл бұрын
If u r perfect answer dis I have done all d work as i seen d vedio but Stil my phone read d face and setup face id complet but when i lock my my phone then not open phone. Swap d phone massage display
@abdul_official143
3 жыл бұрын
A sake not edit
@kymdickson3686
2 жыл бұрын
i don't get why theses videos . just have writing why would i look for a video on how to do something. if I wanted to just read something with pictures i would read an article or find some site on google, just bugs me... i came for a talk through not a read through
@Elekworld
2 жыл бұрын
Thx for advice, Kym. Pls check our latest videos, we've complete videos with audio for better understanding. Pls stay tuned with us if you like our video and content. :-)
@ffranzisek
3 жыл бұрын
it? a big fake !!! I tried yo copy an original face id module to another and it does't work. the replacement part is ok an the original also,. is wasting your time and money! verry disapointed
@Elekworld
3 жыл бұрын
Bro, it won't work if you use another original Face ID module, because data can't be burn in it by 3rd party except Apple itself, it wasn't designed for this. You have to use JC blank dot projector flex and its device to complete the repair.
@zodcybercontactthemoninsta3184
3 жыл бұрын
I'll recommend Gacktech on Instagram to you.. He's very fast and reliable
@syedomairrr
2 жыл бұрын
Sir. I am having a Querry My face id is asking to move phone lower and higher. But my Dot projector and flex cables are working fine. We checked it on Flex cable data copying Device Face Id status is normal. Portrain mode is working Fine. But still face id is not working
@Elekworld
2 жыл бұрын
Hey Syed, pls check below two potential problems: 1- if the flood illuminater flex damaged or not; 2- check if all the portrait under natural light still workable.
@syedomairrr
2 жыл бұрын
@@Elekworld sir Both are working Fine. portrait Under Natural light and Flood illuminator Flex
@Elekworld
2 жыл бұрын
@@syedomairrr One more possibilities: Need adjust the infrared camera location slightly higher or lower. You don't have to move infrared camera, just adjust the metal bracket which hold infrared camera higher or lower. And pls note don't touch Dot projector camera when you doing this.
@Abdualhafeez-x2i
3 жыл бұрын
Nice
@Elekworld
3 жыл бұрын
Thanks for comment, pls subscribe our channel for more helpful update. :-)
Пікірлер: 121