I agree by far the worst part of changing the turbo is those band clamps... I used a grinder to cut them off with ease, but getting the new band clamp on the lower driverside was a total pain in the ass....
@JohnKangas
3 жыл бұрын
I don't even know how you would have got a cutting tool back there!
@TheRealSlowhand
3 жыл бұрын
@@JohnKangas I got a small die grinder in there for the upper 2 band claps and a prybar on the lower clamp... Surprisingly it wasn't too difficult...
@JohnKangas
3 жыл бұрын
Nice! Good thinkin.
@clintonbrown3528
3 жыл бұрын
Keep them both. 100%
@JohnKangas
3 жыл бұрын
I think you're right
@dr.bowdoin3067
3 жыл бұрын
I’m jealous brother I’m still rocking the stocker down bottom. She sounds good!
@JohnKangas
3 жыл бұрын
I think it turned out pretty sweet!
@justinbenton1819
3 жыл бұрын
Did you figure out the manifold absolute pressure ive been getting the same code I've got the same setup just the s475
@JohnKangas
3 жыл бұрын
It might be your tune. Who's tunes are you running? Cuz I think that code comes from pushing more than stock amounts of boost. So that needs to be tuned out.
@justinbenton1819
3 жыл бұрын
@@JohnKangas I've got spe tunes I may need to call them
@JohnKangas
3 жыл бұрын
Yeah give them a call and see what they say.
@ty_little1
3 жыл бұрын
I love my single. I run a 366 SXE Borg Warner with a Exergy 10mm stroker pump, and 220 Fass. All MPD piping. Dyno day is coming. I bet I’m at 700 for sure.
@JohnKangas
3 жыл бұрын
Yeah I would definitely put my money on you being over 700 with that setup. Lemme know if you take any videos! I'd love to make a video on it if you're okay with that.
@ty_little1
3 жыл бұрын
@@JohnKangas okay, can do man.
@dr.bowdoin3067
3 жыл бұрын
@@ty_little1 how many lbs of boost are you seeing on that set up?
@ty_little1
3 жыл бұрын
@@dr.bowdoin3067 more than the stock sensor can read. I do not have a new sensor yet. I need to order one. I believe it’s 42.6. When I get the new sensor I will let you know though.
@JohnKangas
3 жыл бұрын
I think the stock sensor maxes out at 42.6.
@thewooginator83
3 жыл бұрын
Dude I've been mulling over what route to take when I do decide to upgrade my truck and I think you've sold it for me. I am super impressed with how clean it runs! I'm going to be towing quite a bit, so I didn't want to give up the bottom end spool and exhaust brake capabilities that the VGT turbos allow. My power goals are quite a bit less than yours though (for now hehe), so I may end up just upgrading the turbo in the valley for the time being. Are you at all concerned with your bottom end or transmission now that you are potentially pushing some bigger numbers?
@JohnKangas
3 жыл бұрын
Not too concerned with bottom end or trans for now because I'm still on stock injectors. Before upgrading injectors tho, I'll definitely build the bottom end before the send. The trans should be good for that power level too as long as long as the tuning is good.
@deerturk88
3 жыл бұрын
Anything done to the trans? Miles?
@JohnKangas
3 жыл бұрын
95k and no trans work
@clintonbrown3528
3 жыл бұрын
@@JohnKangas that’s impressive 👏👏
@joeys6356
3 жыл бұрын
I feel like it would be badass to keep both of them but if you don’t I would say maybe just get the pusher intercooler piping system and just run that with the single valley turbo.
@JohnKangas
3 жыл бұрын
Im pleased that you can hear the new valley charger pretty well actually. That being said, I'll prolly run this for a few thousand miles. Definitely get it on the Dyno again.
@samdonovan4017
3 жыл бұрын
I have the 55 over kit as well... what do you think actually failed? If it didn't throw metal through the system, what could it have been?
@JohnKangas
3 жыл бұрын
I really have no idea. I had to send it back to the guy who built my stroker pump, so he said he'd investigate further.
@zachsanders1995
3 жыл бұрын
So cool man!! I wound up getting that 21 I mentioned the other day. Now I’m broke :\
@JohnKangas
3 жыл бұрын
That's going to be a great platform to build on tho!
@tykraft3534
3 жыл бұрын
I’ll buy your compound setup. I got a s370 ball Bering from SPE and need another turbo in front of it
@JohnKangas
3 жыл бұрын
You wanna buy the one on my truck?
@tykraft3534
3 жыл бұрын
@@JohnKangas yeah 😂
@JohnKangas
3 жыл бұрын
Hahahah imma have to think long and hard about that one
@calebleuciuc670
3 жыл бұрын
I'd probably just make it a single turbo, simpler and less things to go wrong
@JohnKangas
3 жыл бұрын
Yeah you've got a point!
@134nick
3 жыл бұрын
You cannot make 800 hp on a single 66vgt turbo lol
@JohnKangas
3 жыл бұрын
How do you know that? Cuz you're right, you need the fuel to support it. Modified cp4 and 60 over injectors would do it.
Пікірлер: 52