very useful information on F3!!~ hope to see more Nikon F3 repair video !!~
@diyextravaganza
2 жыл бұрын
If I have to work again on a F3, certainly. 😊
@Carl.65
2 жыл бұрын
Thanks for another clear and straight forward video. Do you know if the F4 finder is very different to the F3? My F4 is a little dusty.
@diyextravaganza
2 жыл бұрын
I need to take a look at a F4 finder before telling you for sure. Cheers.
@charlsonnyledelacerna8080
Жыл бұрын
Thank you very useful
@diyextravaganza
Жыл бұрын
Hi, you're welcome. Don't forget to like, subscribe and tell all your friends about the Channel.
@GeorgiosKalaydjian
10 ай бұрын
Thank you, very helpful. Can you make a video for cleaning Nikon F4 viewfinder please.
@diyextravaganza
10 ай бұрын
Hi, I'll try to make one whenever I have an F4 finder available. Cheers.
@GeorgiosKalaydjian
10 ай бұрын
@@diyextravaganza Thank you 🙏🏼
@GeorgiosKalaydjian
Ай бұрын
@@diyextravaganzaHello again, what about if I send you my F4 viewfinder so you can make a video and clean the lens which has a spot from the interior face, where do you live?
@MrFreakwent
7 ай бұрын
So helpful!
@diyextravaganza
7 ай бұрын
You're welcome 🤗
@KimHojbergJensen
2 жыл бұрын
I have saved this in case I will need it. have one issue with my 3: When I open the door to the film department, a little pin should pop out in the upper left corner - then when you close the door it resets the frame counter. Mine doesn't come out so it doesn't reset. I have to remember how many shots I have taken. Do you know about this problem?
@diyextravaganza
2 жыл бұрын
Hello, honestly I don't. You should ask in the learn camera repair group on Facebook. Someone will know for sure there. Cheers.
@davidpound3106
11 ай бұрын
Hello, does anybody know the size of the 4 small screws that secure the top plate to the unit?
@diyextravaganza
11 ай бұрын
I don't have a finder around so cannot measure, but my bet is either M1.6 or M2. Cheers.
@chelsievalerio854
Жыл бұрын
How would you take out the bumps on the top cover?
@diyextravaganza
Жыл бұрын
I'll take a small piece of hard wood (like a stick) and a small hammer and I'll start hitting from behind. Cheers
@chelsievalerio854
Жыл бұрын
@@diyextravaganza does it need to be heated or anything ?
@diyextravaganza
Жыл бұрын
I don't think so, just be patient and go progressively. Cheers.
@av8bvma513
2 жыл бұрын
03:25 Eyepiece Shutter.
@diyextravaganza
2 жыл бұрын
Thanks!
@reddevil211287
Жыл бұрын
What if the mirror is dusty? Im scared to touch mine :(
@diyextravaganza
Жыл бұрын
mirrors are tricky because very delicate. Try blowing, or a very soft microfiber cloth. cheers.
@reddevil211287
Жыл бұрын
@@diyextravaganza thanks for the reply. I read somewhere there could be some kind of surface coating applied, I was unsure of ruining it. The layer of grime on it though is making the image in the viewfinder very dull. Even less so than my FM2, which is a much smaller magnification with less light coming through. My F3 is mint condition otherwise, so I'll play it safe and just keep it as is. lol They don't make em like they used to.
@diyextravaganza
Жыл бұрын
@@reddevil211287 yeah, the silver or aluminum coatings in mirrors is very delicate. One approach is to wash it with a mix of distillated water and isopropyl alcohol and remove the grit gently with your fingers. Then rince with distillated water. Distillated water is essential so not to leave traces on the surface once it dries. Cheers.
@reddevil211287
Жыл бұрын
@@diyextravaganza Great suggestions, I think others will benefit from this chat too. :)
@diyextravaganza
Жыл бұрын
@@reddevil211287 I certainly hope so.
@yummygogolak
2 жыл бұрын
You should have gone all the way and pulled the prism.
Пікірлер: 30