IMPORTANT: Do not remove the battery connector if you can avoid it. You can carefully pry up the battery and place it aside while it is still connected. During removal or replacement of the battery connector, if you inadvertently touch a very small, grey “fuse” right beside the connector with anything metallic, it can short out, resulting in the JoyCon’s battery becoming disconnected from the mainboard and no longer able to power it. The JoyCon will still work when docked but ONLY when docked. -Sheldon Carpenter Happened to me one time, so watch out and just skip step 3.
@commanderredjonkks5268
Жыл бұрын
That's probably why this video specified using non-metallic implements for all the steps like that, but it's nice to know what to look out for and that it's possible to work around the step the video describes as "scary"...
@veero8130
Жыл бұрын
My right Controller fell down and now it doesn't work anymore, only in handheld and only if the switch is charging while in handheld 😭
@marcgyven
Жыл бұрын
Not to mention that reattaching the battery was the hardest part of this whole process for me.
@RJWaynerium
Жыл бұрын
@@veero8130 sounds like the battery came unplugged? Easy to take apart and verify
@darkacb8422
Жыл бұрын
before starting any repair, you should ALWAYS disconnect the battery.
@lancefisher8358
3 жыл бұрын
The fact this video exists is a bad image for Nintendo, wish they had a better design
@ff343355
3 жыл бұрын
lol they do it on purpose so people will buy more joycons, if you send it to nintendo and they're special edition joycons they'll send you grey/blue/red ones back as replacement
@dewolf123
3 жыл бұрын
@@ff343355 That's an utterly low and scummy way to leech off ppl, they're rich as hell why the hell do they even need to do that it'll literally be chump change compared to buying whole products anyway.
@afifsahrin5708
3 жыл бұрын
@@dewolf123 it's called business. nothing to do with if you are rich as hell or not
@otiko8412
3 жыл бұрын
@@afifsahrin5708 it's called not being ashamed
@Gigi-zr6hp
3 жыл бұрын
@@dewolf123 products aren't built to last nowadays, especially tech products. This is not just on consoles but smartphones and electronic vehicles as well
@jackwoodhead
3 жыл бұрын
Tip for viewers who haven't seen VK's video: if you firmly press down on the plastic right above and below a drifting joystick and the drift goes away while you're squeezing the plastic, that means this fix will work for you.
@TheSaintsVEVO
3 жыл бұрын
Thank you! Does this work for a ps4 controller as well?
@jackwoodhead
3 жыл бұрын
@@TheSaintsVEVO No; ps4 controller drift doesn't appear to be caused by the same issue so this test and fix probably won't work.
@queendopamin
3 жыл бұрын
can confirm it doesn't
@hunyadimolnarmatyas7822
2 жыл бұрын
@@TheSaintsVEVO that was a very dumb question bro…
@alexism9656
2 жыл бұрын
@@hunyadimolnarmatyas7822 people are allowed to ask dumb questions. They didn't know, and now they do.
@TheJadedJames
3 жыл бұрын
"We've fixed the joy-cons, thanks to recent advancements in cardboard box technology" - Master Miller
@gitgud2523
3 жыл бұрын
Snake had the right idea
@eros439
3 жыл бұрын
Last word in stealth infiltration technology
@Old-Boy_BEbop
3 жыл бұрын
nintendo will capitalize on this feature and create a joycon drift Labo kit
@TheJadedJames
3 жыл бұрын
@@Old-Boy_BEbop We need a Metal Gear game on Switch where they make a meta joke about this
@liammcnulty1987
3 жыл бұрын
Underrated
@セータン
3 жыл бұрын
Trust me, Nintendo knows how to fix it. They just won't bother because people would buy new joycons every month because of the drift.
@EstebanCodes
3 жыл бұрын
Even worst it may be a case of Planned obsolescence
@forbiddene705
3 жыл бұрын
They just see the money pouring in and have no intention to stop it. Greedy
@reinforcedpenisstem
3 жыл бұрын
That's probably true
@purge3883
3 жыл бұрын
Makes me sick
@RileyJustHappened
3 жыл бұрын
No, they can't do the fix because that would be admitting fault, which they never have, and would be an instant fail-state for all the law suits against them.
@Decastellac
3 жыл бұрын
You’re telling me all Nintendo needs to do is put a piece of paper in there controller and this whole issue goes away
@stoheha
3 жыл бұрын
Or, perhaps make the housing for the control stick slightly thicker. Still not as bad as the N64 controller design flaw where the base of the stick gradually erodes from grinding over time.
@bobthemagicmoose
3 жыл бұрын
My guess is that a plastic piece wears down that allows the joystick to have more play in it, the cardboard just adds extra pressure to compensate for the worn plastic. So when the plastic wears down more, you'll need another piece of cardboard to compensate more. Also, doing this to a new joycon likely would quicken the wear on the plastic causing drift sooner.
@christopher32074
3 жыл бұрын
@@bobthemagicmoose According to VK’s channel, the bottom of the control stick of the Joycon starts to warp after a long time of use which affects the inputs of the control stick.
@foxmamer
3 жыл бұрын
@@bobthemagicmoose watch the original video for the fix, the person goes into detail explaining what's the issue
@parkerking6410
3 жыл бұрын
@@christopher32074 More specifically, the pads the joystick interfaces with aren’t fastened, so pressing the joystick button slower pushes the housing over time. This cardboard paper applies enough pressure to keep the housing where it should be.
@sauceyeti4381
3 жыл бұрын
Nintendo: **Doesn't fix joy con drift** Everyone: "Fine, I'll do it myself"
@chan13153
3 жыл бұрын
new report coming out that many peoples joycons from as far back as 2018 has foam padding where you place the cardboard.
@sinper480
2 жыл бұрын
Did it work
@Concise_Parakeet
2 жыл бұрын
@@chan13153 damn
@Concise_Parakeet
2 жыл бұрын
@@sinper480 it might have
@reminagyo2973
2 жыл бұрын
WHOLESOME 100 FELLOW REDDITOR!!!!!!!!!
@DisneyTLK110
3 жыл бұрын
It's because the conductive pads get scraped away after use. Cleaning them out with contact cleaner (after opening up the stick modules themselves) works wonders. All this does is creating a more "aggressive connection", pushing the metal tabs closer to the conductive pads, thus improving the connection regardless of uneven conductive surface or debris.
@TS_Mind_Swept
2 жыл бұрын
Even if that's true (which he did address in the video), it'd still help
@firmbutton6485
2 жыл бұрын
need a video how to do this
@McStebb
2 жыл бұрын
Or perhaps Nintendo could stop building components out of cheap, high-wear material, and sacrifice just the SLIGHTEST bit of thinness in order to install a robust, durable joystick module. This race to make everything as thin as possible has lead to so many problems.
@Troyadvica2472
Жыл бұрын
The fact this video exists is fine. The fact it has 600k views is a problem.
@dinham16
Жыл бұрын
When you do a quick some compared to worldwide figures, only 0.5% have watched this video, no problem there
@SimplyLyrical999
Жыл бұрын
Underrated comment 👏
@annihilus6724
5 ай бұрын
tHe FacT
@Arnaualgi
3 жыл бұрын
It's insulting that Nintendo won't fix their cheap console assets themselves.
@andrewmason8309
3 жыл бұрын
They will. For free.
@mcruff3
3 жыл бұрын
@@andrewmason8309 They keep producing hardware prone to issues. Just because they will fix it doesn't mean it's fine. It takes ages for you to send it and to get it back.
@stupendously_silly
3 жыл бұрын
@@andrewmason8309 not in all countries no, they specifically fix it in countries that could sue them then ignore the rest. Because you know. King of bare minimum.
@Cayden675A
3 жыл бұрын
The reason why is because it’s actually really hard to mass produce fixing the drift in a affordable price and you may argue that it’s more expensive them doing the repairs but not everyone is gonna repair their joycons.
@weismax33
3 жыл бұрын
How can they fix something that is an inherent flaw in the Joy-Con's design? It wouldn't be cost effective to fix the design since everyone who has drifting controllers will want a replacement for free.
@Playstation_Sony
3 жыл бұрын
"you'll need a variety of tools" gave up there lol
@g0507953
3 жыл бұрын
True
@ToniSkit
3 жыл бұрын
You can buy it full on Amazon for pretty cheap - they give full kits
Nintendo: “🤔 What is this…..Joycon drift you speak of?”
@frenchfry7631
3 жыл бұрын
Lmao
@Itherealshadow
3 жыл бұрын
This was a thing for a few years. We just finally found a working fix. And the amount of money nintendo makes they probably care less that we learned to fix it bc they did make it to where we can open the controlers/switch
@chrism7067
3 жыл бұрын
nah not IGN, try VK.
@realJosshhh
3 жыл бұрын
they're perfectly aware of it, they just keep it in the joy cons so that people buy new controllers since switch sales have gone down tremendously after the pandemic.
@VKsChannel
3 жыл бұрын
MOM I'M ON IGN!
@Yuna_Kobayashi
3 жыл бұрын
:D
@Xernamos
3 жыл бұрын
Thanks for all the help man, we're all eternally grateful 🙏🙌
@ncBadrock
3 жыл бұрын
Nintendo next week: Please enjoy our new Nintendo Labo Joycon Repair Set.
@normalhuman4951
3 жыл бұрын
For the cheap price of 100€+ Tools dlc (50€)+ Intructions dlc (80)+ Delivery (99,99€)
@jakederouin9116
2 жыл бұрын
Joy-Con drift is fake. It’s actually the souls of children who died after being caught by their parents playing DS after bedtime. They roam the world eternally attempting to play the latest Zelda and Pokémon games on your Switch.
@Rejkin
11 ай бұрын
Underrated comment
@84Punkmonkey
3 жыл бұрын
Used this fix last week. So far it's holding up.
@mina352
3 жыл бұрын
Same here
@DamnitMan88
3 жыл бұрын
@@subtegral 24 hours a day for 7 days! 168 hours of continuous moving the joystick around and playing game. It's truly amazing!
@theredmeadow
3 жыл бұрын
Did the fix and worked for a couple days. Back to drifting.
@CloneClooney
3 жыл бұрын
@@theredmeadow Try to find construction paper or the thinnest bit of foam padding maybe. The paper probably moved slightly when you reassembled the joycon. Did mine two weeks ago and its been perfect since.
@felixpham4934
3 жыл бұрын
@@DamnitMan88 obviously every switch user uses their switch 24 hours a day without eating, sleeping or any other activities
@NawTNicky
3 жыл бұрын
Really easy to repair this. Takes like 5 minutes. Worth it
@bennycaustic5102
3 жыл бұрын
I'm pretty sure the reason Nintendo hasn't fixed joycon drift is because they've been sued and taken to court over it several times, and if they fix the issue they're admitting there was an issue.
@unfavred4205
Жыл бұрын
And so you buy more joycon's
@Dtgray12
3 жыл бұрын
Step One: Sue Nintendo for a blatant design flaw.
@christopher32074
3 жыл бұрын
Step two: Expect a defeat on your lawsuit.
@marinbelle
3 жыл бұрын
Step Three: ????
@RaymondStormbl3ssed
3 жыл бұрын
Step four: Emulate
@marinbelle
3 жыл бұрын
Step Five: Profit!
@christopher32074
3 жыл бұрын
@@marinbelle Final Step: Watch VK’s Channel on how to fix your faulty Joycon and it’ll defeat those corny and pathetic Joy Con drift comments on KZitem.
@hyperdrivepics
2 жыл бұрын
My joycons had gotten borderline unplayable during Breath of the Wild. Impossible to use the bow and arrow, messed the camera up constantly during everything else. Tried this fix just now and everything's perfect again. Stable ci tools, and the rumble seems to be on more often now. Thanks for posting!
@jestes7
Жыл бұрын
how is it now?
@mybaIIz
Жыл бұрын
how is it now?
@asghol
2 жыл бұрын
Thanks for this tutorial. Fixed both my left joy-cons with ease. Didn't have 5mm business card but used double A4 photo paper with the glossy sides inwards. Works so far.
@jestes7
Жыл бұрын
how is it now?
@ijustpulledthetrigger5482
Жыл бұрын
How is it?
@j3kwe
2 жыл бұрын
Controller reliability are the catalyst to whether or not a game is even playable. Nintendo, Sony and Microsoft should take this VERY seriously. The one whom addresses this last will never be able to remove the negative stigma.
@KawaiiPandass123
2 жыл бұрын
Me: *excited ready to fix my joycon drift* Him: So you’ll need some tools..
@cristianarreola8582
3 жыл бұрын
Thank you IGN for acknowledging the joycon drift issue.
@mrizaldi7199
3 жыл бұрын
This joycon drift that prevent me to buy a switch. All of my friends who have a switch are having this problem. It's like 100% failure rate on industrial product 😂
@mioda3109
3 жыл бұрын
Yet there are people who actually believe that its not actually a widespread problem and ive even seen people who believe its a myth.
@Master_A1
3 жыл бұрын
To be fair, by that logic you wouldn't be allowed to buy any of the current consoles as they all use cheap and faulty materials for their sticks. You have that on PS5 and on Xbox, too. Maybe not to that extent, but still. Also you could just buy a separate controller for a Switch. Some use the same components for the sticks, but by far not all of them.
@SirWampus
3 жыл бұрын
@@Master_A1 was thinking of buying these consoles but after hearing abt joycon drift ima just stick wit pc
@XyzCloud
3 жыл бұрын
Just get a pro controller like everyone else.
@Master_A1
3 жыл бұрын
@@XyzCloud The rate for faulty sticks are almost as worse as with the Joy-Cons. It just takes a little more while. 8Bitdo controllers are reliable as an example.
@stan110
3 жыл бұрын
The joycon perfectly shows that warranty does not matter and that the manufacturer does not know what is 'best' for the device.
@encrylix9092
3 жыл бұрын
At this point, the fact that it takes the consumers to fix the drift is VERY embarrassing for Nintendo. Obviously they don’t care about their product
@unfavred4205
Жыл бұрын
Nah Nintendo just doesn't care in general
@RJWaynerium
Жыл бұрын
That's a load of crap. You try designing a controller that can charge wirelessly from its host console/tablet in that tiny amount of space.
@lachburn1480
3 жыл бұрын
In Australia, joycon drift is covered under your manufacturers warranty. Just take it to the store you bought and get a new one
@FLIXTERRISCOOL
Жыл бұрын
If it still drifts a little, recomend doing this over and over again untill it doesn't drift, worked for me.
@MrBillRizer
3 жыл бұрын
There is a little rubber sleeve just under the top of the analogue stick, lift it up a little with a toothpick and put a very quick spray of WD40 under it. Works every time. No need to open.
@rolando90s
3 жыл бұрын
Thanks dude
@packerspalmeiras
2 жыл бұрын
Worked for me. Thanks!
@ॐIo
3 жыл бұрын
Nintendo treats their high end products like 2nd grade children's toys
@erfaniom9576
3 жыл бұрын
they are tho...
@christopher32074
3 жыл бұрын
Well they have a strong attraction to kids than Microsoft and Sony.
@MochaFatTart
3 жыл бұрын
@@christopher32074 Smash fans too
@Cclipze
3 жыл бұрын
High end?
@manojlds
3 жыл бұрын
Their high end products are the games.
@sevorg_
3 жыл бұрын
Lowe’s also sells an electronic repair kit that’ll also include a lifetime warranty. So if you break/ lose something you can take it back and exchange it for a brand new kit
@Darksider087
3 жыл бұрын
This issue shouldn't be for the consumer to "fix" especially YEARS after its launch. Oh wait, this video will come in handy for new owners of the oled.👍
@rumblehook9442
2 жыл бұрын
Bough an unpatched switch with everything included plus 256gb memory card for $180. One of the joycons had drift and this trick worked like a charm. Thank you!
@YeetusMingus
3 жыл бұрын
As much enjoyment as I've gotten out of having a switch for the past year, Nintendo's handling of this hardware defect only inspires me to skip whatever their next console is.
@John-gl5ne
3 жыл бұрын
We need to demand better from nintendo
@NoExplosionsMcgee
3 жыл бұрын
And Sony as well as stick drift isn't an issue exclusive to Nintendo platforms.
@andretti10
3 жыл бұрын
We can start by stop buying 3+ year old games for $60
@aihsanasl
3 жыл бұрын
@@NoExplosionsMcgee are you kidding PS Vita don't have such an issue after 10 years.
@foxmamer
3 жыл бұрын
@@aihsanasl he's talking about the PS5 controllers
@JulliusTheGreat
3 жыл бұрын
@@NoExplosionsMcgee But Nintendo's much worse
@MrZekedeezy
2 жыл бұрын
Ooooh someone plays guitar! Thanks bro, yours is the most coherent tutorial for this I've seen so far.
@sants4560
Жыл бұрын
The fact IGN made a video about this is insane.
@geraldserra
3 жыл бұрын
Where are the credits in the video for the channel that really discover this solution?
@Ikuzuno
3 жыл бұрын
Facts
@fatefinger
Жыл бұрын
The problem is this is a Band-Aid. Eventually the joycons will start drifting again. If you’re going to tear it down this much you might as well just replace the entire joystick. You can get them for like $10 a pair.
@DoubleO7-11
3 жыл бұрын
Thanks! Now please make a video for the PS5 DualSense! 😭
@anuron4661
3 жыл бұрын
Words no one ever thought was going to say
@Swerveyy
3 жыл бұрын
The ps5 controller drifts?
@christopher32074
3 жыл бұрын
@@Swerveyy It does and there is already a lawsuit filed against Sony.
@NoExplosionsMcgee
3 жыл бұрын
@@Swerveyy Both DualShock 4 and DualSense suffer from rampant stick drifting as well.
@antoniosanichar943
3 жыл бұрын
@@Swerveyy got two dual-sense and both work fine 🤷♂️, maybe only happens to a few people
@monkeyjayy9892
3 жыл бұрын
I’ll definitely look into this again when my newish joycons mess up
@maxlong839
3 жыл бұрын
IGN does what Nintendon't *cough* oh excuse me, Nintenwon't
@alexanderryufenando9711
3 жыл бұрын
U mean vk does what nintenwon't bcuz vk is the first to found the solution
@DejonckheereWard
3 жыл бұрын
Worked for my blue controller, but not for my red one. The blue has screws closer to the joycon, helping to keep the extra pressure but the red's battery holders screws are further away from it.
@caiodorneles6070
2 жыл бұрын
try two layers of paper
@CaravelClerihew
3 жыл бұрын
How to fix joy-con drift: Hold Nintendo account for their terrible build quality.
@veeetox
3 жыл бұрын
Guys, DO NOT remove the baterry from the joycon. is not necessary at all. By doing that, you can broke the battery connector from the board. So just take the battery and put it aside while you are doing this
@darkacb8422
Жыл бұрын
when doing any repair, you should ALWAYS disconnect the battery before starting. you can get away without doing it, but you risk breaking the device further.
@Vandel212
2 жыл бұрын
Has anyone done this and reported how well the fix worked long term?
@Weirdaljackson
3 жыл бұрын
It worked! Still wish this was an issue that Nintendo themselves could fix but at least there’s a solution.
@2_L8
2 жыл бұрын
Just went to calibrate my controller to see if it showed any more signs of drift after the repair. It hasn't yet. Thanks for the vid
@moe4273
3 жыл бұрын
You guys should credit the guy who found this fix
@jackburns6403
3 жыл бұрын
They did?
@Kniffel101
3 жыл бұрын
They absolutely did, in the video _and_ the description.
@maxwilliams1060
Жыл бұрын
Nintendo are the shittest company for not dealing with this
@joakimjarmland6466
2 жыл бұрын
Nice tutorial, works like a charm! 👍
@icanhazgoodgame3845
3 жыл бұрын
It does not void your warranty. thats a convenient and common misconception. The manufacturer would have to show how you the work you did damaged the device and therefore not responsible for your at fault damages. Opening and servicing a device is not on its own a warranty voiding action. However products are often cheaper than lawyers so they get away with it.
@zumbyzoonvy2
3 жыл бұрын
Its funny how they put a N64 at the background, the "strongest" console in the history
@rafaelballarin9969
2 жыл бұрын
I've just done it to my left joy-con. It worked like a charm. Thanks!
@JulliusTheGreat
3 жыл бұрын
What's dangerous are the people who buys new joycons whenever their old ones get the drift, they are encouraging Nintendo on sustaining their malicious practices.
@PfeffergrubenNick
3 жыл бұрын
Thanks to VK's Channel for that fix.
@tiagoj8020
3 жыл бұрын
Right to repair baby!
@scottgrant2825
3 жыл бұрын
Technically it can be repaired and they are doing it for free. However it shouldn't be happening on such a large scale in the first place. Nintendo should be sued for knowingly selling faulty products.
@GoogleAccount-tg9lp
3 жыл бұрын
How does IGN make money if they just reuse other people and companies videos
@choloeseguay
3 жыл бұрын
Ads
@XgamerdaveX
3 жыл бұрын
Because you clicked on the video and commented which boots engagement. You probably got served some ads too.
@yeahhbuddy3932
3 жыл бұрын
Well your subbed are you not?
@christopher32074
3 жыл бұрын
To make it more viral.
@GoogleAccount-tg9lp
3 жыл бұрын
@@christopher32074 that doesn’t translate to profit, it’s most likely ads
@Tech_4_Fun
2 жыл бұрын
remember everyone with Joy comes Cons
@xenobreak1160
2 жыл бұрын
Thanks Dad...
@SaikaDeWinter
3 жыл бұрын
Had swapped both sticks myself like 2 years ago. Knock on wood but they havent drifted since then and been loving it!! ^-^
@TEMSproductions
3 жыл бұрын
Where’s the “BuT n1nT3ndO fix3s tHem f0r fr33!!¡” bootlickers?
@mauriceseebauer5748
Жыл бұрын
this actually fixed my joycons thanks alot and for saving me money .
@TheRealHedgehogSonic
3 жыл бұрын
You know your problem is awful when IGN of all people start telling your user base how to fix it.
@TonyGonzales
3 жыл бұрын
The irony of KZitem commenters (of all people) thinking they are above the gamers at IGN. Such pathetic gatekeeping on a very handy video, one wonders what you've done for the community outside of whinging.
@veero8130
Жыл бұрын
This worked for me. Omg Nintendo get your sh*t together....
@laryssalima6435
2 жыл бұрын
Didnt work for mine :/..
@TheDNW
3 жыл бұрын
worked great. Didn't have to disconnect battery or antenna though
@DaddyGamerFred
3 жыл бұрын
You know it's bad when IGN is making how to videos on how to void your joycon warranty 🙃
@foxmamer
3 жыл бұрын
That's why right to repair is important baby
@Syddy_
3 жыл бұрын
now this fix should make it easier for nintendo to fix the problem entirely, but if nothing comes of this then it's gonna be really disappointing
@Vitoreo
3 жыл бұрын
Solution 2: buy steam deck.
@ToxynCorvin8008
3 жыл бұрын
Metroid Dread on the Steam Deck is gonna be so sweet!
@JGLCSW
3 жыл бұрын
@@ToxynCorvin8008 so will Super Metroid, Metroid Prime, and Metroid 2.
@otiko8412
3 жыл бұрын
@@ToxynCorvin8008 It's really going to be lol
@christopher32074
3 жыл бұрын
The emulator Yuzu is completely crap. It runs Switch games at a extremely slow speed and very low framerate.
@otiko8412
3 жыл бұрын
@@christopher32074 yes, that's why the Hades project is coming
@abu7880
Жыл бұрын
Thank you so much for this. It helped me sort the drifting issue in my left joycon
@bilanggoboy
2 жыл бұрын
THANK YOU!!! This fixed my joycons! Cheers!
@Aragorn7884
3 жыл бұрын
Shouldn't need to "fix" a purchased product from a Fortune 500 company...
@LuciusAugustusRex
3 жыл бұрын
It's so sad that Nintendo refuses to fix this because they would be admitting fault.
@tablespoon1277
2 жыл бұрын
imagine the compensation they have to bare if they admit this?
@lewinski8147
2 жыл бұрын
But they have ? Was the apology and offering to fix the issue not them admitting the fault ?
@richardtaveras3642
2 жыл бұрын
@@lewinski8147 they still continue to make the faulty joycons though, they clearly didn’t learn anything
@shadowcelebi3595
3 жыл бұрын
but what about for those that have a nintendo switch lite though? that console also has joycon drift.
@piperjojostott7790
3 жыл бұрын
Now there's a slight bulge around the thumbstick area. I'm honestly concerned that this creates a tiny gap above the black bit where the SL and SR buttons are.
@miketyggr1817
3 жыл бұрын
Tool kit with all necessary tools, pick, brush, tri screwdriver, etc. $8.00 on Amazon for a boxed kit.
@GottaLoveDepecheMode
3 жыл бұрын
Link pretty please??? 🙏🙏
@mathews2774
3 жыл бұрын
@@GottaLoveDepecheMode me too 🥺👉👈
@Gainedfire
3 жыл бұрын
Just tried it right now! And it works thank u so much! 🙌🏼
@InfraSolart
3 жыл бұрын
5mm Card Stock? That doesn't seem right.
@joshkyer5280
3 ай бұрын
Every controller I've had starts drifting to the left. Never any other direction
@drvpgvng
2 жыл бұрын
Gamers like me remember this stuff for life and end up supporting Sony instead
@Flshstick99
Жыл бұрын
Thank you so much ING
@adriansvarela
2 жыл бұрын
Unfortunately it’s useless if you don’t have the Nintendo screwdriver :/
@davidmiller-zf8zl
8 ай бұрын
You lost me at the tools. I'll just buy new joycons. Damnit!
@grimey666
3 жыл бұрын
how to fix joy-con drift: buy a steam deck
@JJ-ob7np
3 жыл бұрын
Not if FPS shooters are nearing death
@SekiberiusWelkesh
3 жыл бұрын
@@JJ-ob7np What?
@grimey666
3 жыл бұрын
@@JJ-ob7np i think you need to look at what exactly the steam deck is again lol
@soccer5stud
2 жыл бұрын
worked like a charm. Thank you!
@greenfrogbad
3 жыл бұрын
Way to monetize other people's work.
@TheZax85
3 жыл бұрын
Agree… They could at least give some more credit to VK!
@greenfrogbad
3 жыл бұрын
@@TheZax85 "But we gave him a shout out!" And then proceeded to duplicate his work so people would be less likely to check out VK. These soulless corporate vultures make me sick.
@ManueldelOlmoPomares
2 ай бұрын
Worked like a charm for me!
@aaditlehther3755
3 жыл бұрын
IGN stole this video from a small KZitemr that’s so embarrassing
@captainsomeister
3 жыл бұрын
One of my Joy cons is experiencing drift right now
@matheusnico1as
3 жыл бұрын
Holy moly Nintendo, it's not because it was designed in Tokyo that the joycon should drift
@TheGreatFryMaster
2 жыл бұрын
Sad that nintendo is so bad at making a controller that people have to go out of their way to dismantle, and possibly risk harming their controller just to fix a drift issue
@sheikahblight
3 жыл бұрын
You do not need to disconnect your Batteries. It makes it more complicated for no reason
@kapp8454
2 жыл бұрын
When fiddling inside electronic component’s you should always disconnect the battery due to ESD.
@sheikahblight
2 жыл бұрын
@@kapp8454 You are putting a piece of cardboard inside. You aren't messing with components.
@Bugatti12563
3 жыл бұрын
The real Nintendo Labo starts here.
@TheFallenStarlight
3 жыл бұрын
Now that Nintendo knows what the problem is. They just need to go back to the manufacturing facility, remold the processing plate for that specific part. Then release in retails stores and online for this holiday season and beyond.
@brady9592
3 жыл бұрын
Give the creators in the description who worked on this some views!
@jasongrace9114
3 жыл бұрын
Nintendo: Thanks for identifying the problem for us, we will now commence fixing the joycon drift, claim all credits and pretend we didn't know anything about this solution.
@chan13153
3 жыл бұрын
Actually new reports are slowly coming out as people are attempting this repair and they are seeing foam padding at the area where this person said to put the cardboard. People are saying that joycons from around 2018-2019 have this padding.
@PunkSolar22x
3 жыл бұрын
WD-40 (for electronic) silver can. Fast, Cheap, Easy works Everytime, No Tools, No Disassembly Required. Spray under the rubber on Joy Sticks boom your done.
@amypenman970
3 жыл бұрын
Do you have to redo it alot?
@andreatordin3350
3 жыл бұрын
Used the same one! Worked right away, but it’s probably a temporary solution.
@alicevitoriano
3 жыл бұрын
won't work if the problem is the contacts getting separated from the analog, which is what the cardboard fixes.
@forbiddene705
3 жыл бұрын
@@alicevitoriano Exactly right, spay just gets rid of debris
@rtcng3111
2 жыл бұрын
Thank you
@jaredekelman4229
3 жыл бұрын
Thank You for the Info and Assistance! I'm Sure That Will Come in Handy for All of Us!👍
Пікірлер: 983