After further research, it appears all you had to do was flip the Oil pump worm gear and you would have been good to go. You installed it correctly in Part 2. (14:23 in this video and 2:12 in Part 2) Hope this helps someone.
@ClintsStreetMachines
2 жыл бұрын
Hey man, glad you're back. Hope you find the issue and get back on the road soon.
@DinasGarage
2 жыл бұрын
Thanks Clint! Congratulations on the 1K
@alantimberman2984
2 ай бұрын
I have been struggling with my 89 for two months thanks for this video I mite get it now
@DinasGarage
2 ай бұрын
Thanks for watching!
@jasonoverton6537
8 ай бұрын
Thanks brother really needed a good sohc ka video an you made it 🎉
@DinasGarage
7 ай бұрын
Glad it helped 🫡
@slowsx5135
Жыл бұрын
Helpful video thanks man!
@DinasGarage
Жыл бұрын
Glad it helped! No problem
@Xhupacabra
Жыл бұрын
Bro made a 17+ min video on how to NOT replace your timing chain
@DinasGarage
Жыл бұрын
Thanks for watching!
@bradynorris1653
Жыл бұрын
Extremely helpful. Thank you.
@dieseldawg7132
Жыл бұрын
Good video
@alejandrocarmona575
Ай бұрын
Exelente
@ididitlikethis1274
Жыл бұрын
So I've got a question: When you put back the oil pump, what position was the distrubutor when you re timed it?
@DinasGarage
Жыл бұрын
The distributor rotor needs to point at the number 1 spark plug
@obanorakugbe5825
Жыл бұрын
Am goin to do the work today
@southlandgasbikes5124
22 күн бұрын
hey man I tore my truck down a while back I'm putting it back together now but I can't figure out where the long bolt on the timing chain cover goes could you help me with that I would appreciate it thank you in advance
@landenmoore4669
Жыл бұрын
What is the correct orientation for the distributor gear? you installed it the opposite direction (in part 2) from how you removed it?
@DinasGarage
Жыл бұрын
The rotor will be pointing to 4 o clock on the distributor which should be pointing a plug wire number one
@sipmeister3611
Жыл бұрын
oh snap i took the crank pulley off without setting the timing hopefully i can recover from this
@titsandwich1842
Жыл бұрын
We're you able to recover? What happened?
@sipmeister3611
Жыл бұрын
@@titsandwich1842 i wasnt able to myslef with little knowledge i knew i sold the truck for 600$
@Bread45
Жыл бұрын
Did you fix it?
@sipmeister3611
Жыл бұрын
@@Bread45 i dont believe so it did start up but it made pinging sounds and huge loss of power. sold it for 600$ someone grabbed it next day they go fast dont let go of it i regret it everyday.
@warrenfrost2887
2 ай бұрын
Hello, what was the cause of you changing the timing chain. Was it rattling or it just didn't want to run? I have a 95 Nissan pickup. Everything seems to be ok but it just won't start
@DinasGarage
2 ай бұрын
Thanks for watching and asking! So my chain was rattling at startups and I had to reseal the oil pan when I pulled the oil pan I found the plastic chain guides s broken in little pieces in the oil pan. So I decided it was time to change the chain. For a no start condition, check to make sure you have spark first, then make sure your fuel is reaching the injectors. If those are all good then more diagnostic will be needed.
@RTHD84
Жыл бұрын
Wonderful engine's, sucks doing these though 👍🏻
@DinasGarage
Жыл бұрын
Thanks for watching. Yeah it kind of sucks to do that. The main issue was that the Chinese stuff I bought from Amazon. The chain was a bit too long and that’s what caused all the issues so I ended up buying a brand new chain, upper cam gear, lower cam gear off of Nissan For less than I paid for the stuff from Amazon. Thanks for watching.
@davidbryant5875
Жыл бұрын
I’m putting a 95 hardbody engine in a 97 hardbody only this I seen different is the mounting holes for the distributor anyway I can tap a bolt to hold it ?
@DinasGarage
Жыл бұрын
Not really sure I know they are different and I don’t think it will line up with the oil pump shaft. I would just pick up a 97 distributor
@anthony13machado
5 ай бұрын
You have to change timing cover to a 97
@Doritos-7
Жыл бұрын
I saw one thinking about buying for the ka24e ,is a adjustable sprocket I know the rattle are commun on this trucks heard this sprocket also give the truck bit extra power on the rpms
@DinasGarage
Жыл бұрын
I would also get the self adjusting tensioner it’s from Martin Industries www.martin-industries.net/product-page/nissan-ka24e-self-adjusting-tensioner
@jkingjdm8470
10 ай бұрын
What if your notch doesn’t line up
@alexisirias2916
Жыл бұрын
What's up bro...quick question...I took off the power steering pump and belt prior to setting the timing...is that ok or is not right? And I also noticed that once I set the to sprocket in the center and the dot at 3oclock, the bottom little spike doesnt line up on the 2 dash on the pulley..can you advise me please..I'm not a mechanic just a diy kinda dude....thanks bro.
@DinasGarage
Жыл бұрын
Hey man, yeah it’s fine to take those off… as for the pulley not lining up, I would make sure it’s at the compression stroke of piston number 1. Turn the engine over with a ratchet, with your finger or someone’s finger in the number 1 spark plug hole, you will feel the compression push your finger away that is how you know your on the compression stroke.. then check your lines again.
@saintpeterson5275
Жыл бұрын
Is it the same configuration with the Terrano1/Pathfinder Z2.4 gas wagon/suv?
Пікірлер: 41