I’m just a KZitem mechanic. I watch videos like yours to do a job that I don’t know how to do. Your video will allow someone to sort of get the job done, but A1 Auto has a video that shows a little better a complete job. You did bare minimum to get it done, but also made more work for yourself by taking the motor apart to get it back in in an already difficult place to work. Had you taken the time to remove a few panels, bracket and vents it makes the job a little easier. Still took for almost 4 hours. I feel if I’d have tried it your way I’d still be working on it.
@markroberts6030
Жыл бұрын
When posting a video of a specific vehicle be sure it's the correct year I started taking my wife's rogue apart and this video is incorrect for the 2017 nissan rogue blower motor is on the passenger side entry
@cohenmason4555
4 ай бұрын
maybe do your due diligence before you start taking cars apart bud
@davidclark1222
Жыл бұрын
Hi. I have a LHD Qashqai which looks very similar set up. If the fan is noisy then you can get to the inside of the fan cage to clean from behind the glovebox. Happy to chat/show photos
@johnhall502
Жыл бұрын
Remove 2 10mm bolts to that metal bracket holding the driver’s right side underdash panel and the fork that holds the pin for the brake. After that it’s pretty much as you said, only without the motor & pass side dash disassemble. Nonetheless, great video! Keep ‘em coming. Definitely very informative!!👍🏻
@dustinabbott7186
9 ай бұрын
This was a lifesaver. Thank you
@rd7935
Ай бұрын
Does taking out the two 10mm nuts release the bracket so it can be taken off? That bracket is in the way and I can’t take the blower motor out. Any help would be greatly appreciated. Thank you in advance!
@magellan35
Жыл бұрын
Not mentioning the year is sooooo frustrating.
@mrnic3guy305
Жыл бұрын
You have to take of the bracket 2/10mm nuts a swivel and 2extenstion bars a 10mm deep socket.take off the ac actuator on the side near hvac duct before you get to blower motor 2 Philips head screws and you won’t have to fight getting it out.and there’s a Phillips head screw/nut holding the blower motor in place was told it was an 8mm but 8 didn’t fit and the 7.5 was too small so I used a Phillips head screwdriver with an extension.once you get that off then there’s a tab on the bottom of the blower motor but at 12 o’clock pull tab downward and twist the blower motor counter clockwise.this way you won’t have to take apart the blower.just did my mom’s vehicle it was rough because it was my first time ever doing this. It kicked my ass bc it’s tight down there on the floor but i got and my moms is ecstatic. I couldn’t let her pay $350 for that.shoutout to TRQ automotive video . I give you credit for doing the job though
@johndavid3598
3 ай бұрын
swivel and extensions make it easy
@erictyler6371
9 ай бұрын
What year is this Nissan rogue
@simonegoodrunning7893
Күн бұрын
How do you unclip the pedal ??????
@jamesparent1525
Жыл бұрын
Just replace mine on a 2014 just remove the plastic under the steering wheel and then 4 bolts holding a metal plate on then 2 mm bolts will. Remove that bracket then pull blower motor out so easy
@MrFumio17
Жыл бұрын
Best video quality I've seen for an auto repair on you tube. However I can't quite makeout exactly what you are doing at the point the motor releases. A description of what I'm up against follows, my hope is you can give me assistance. I understand there is a type of retainer clip around the 7 o'clock position at the motor rim but I'm unable to determine what or where it is. Clearly it must be there as the motor only moves a very tiny bit when I wiggle it. Somewhere i read an instruction that you would push the retainer to release. It appears that you did do something in that area just before the motor turned freely. Could you give me some insight as to whether I should be pushing in toward the center of the vehicle or pushing so as to move the clip toward the center of the motor itself.
@MrFumio17
Жыл бұрын
after much experimentation, the white clip should be pushed toward the center of the motor. 😂
@mr.barney8147
Жыл бұрын
move the blend door u can only take out 1 screw move it back and turn it out the way
@Wreckitrc224
Жыл бұрын
If you would of taken 5 more mins to take the instrument cluster out you could of unbolted that bracket that was in your way and it would of came out as an assembly
@alexissalva4577
2 ай бұрын
Thank you
@TheMwjb89
Жыл бұрын
What symptoms did this blower motor have? Was it dead? Did it blow a fuse?
@asankovlogs
Жыл бұрын
My check engine light is on now???
@mr.barney8147
Жыл бұрын
I got it out u sorry son a u just gotta turn it around back wards
@DavidStrchld
Жыл бұрын
Yes there is a way of getting it out by playing with it enough. I forgot the details but managed it.
@johndavid3598
3 ай бұрын
Not hard
@HHIVR4
Жыл бұрын
What a dumb design.Nissan engineers never cease to amaze me.
@fidelsimental7056
Жыл бұрын
What year is the Rouge?
@marcusbartels3015
Жыл бұрын
Tell you what year it ain’t… A 2017… don’t ask how I found out 😫
@cashewABCD
Жыл бұрын
Not 2014 either. Use the Glove box passenger side dash removal method. Instrument panel, radio, ignition, unscrew radio, glove box, five screws, side cover, one screw, vent, dash panel, fan easy there.
@Liftium
Жыл бұрын
I believe it's the first generation 2007-2013
@mrukhsar9819
Жыл бұрын
Remove number 10 two nuts and you don't need to get access from passenger side.
@johndavid3598
3 ай бұрын
No man, actually pretty easy to remove.
@nijovacisoen4395
4 ай бұрын
All you had to remove was the brackets and the motor black box thing and comes out in one piece you are doing slot of hard unnecessary work there
@chrisjc2009
6 ай бұрын
Bring back the dislike button count so I know which videos to avoid. 🥴😑
Пікірлер: 34