This is Hugh Robinson from Nitro Addictions lives. Man that took a beating lol.
@Nitro_rc_life
10 ай бұрын
Awewww shit man that sucks
@Nitro_rc_life
10 ай бұрын
Chrome is Hella hard usually won't scratch the piston always takes the damage
@lowellfunk8974
10 ай бұрын
Bashed a bit too hard in the past, this blowup was just an impending disaster waiting to happen. Rebuild it and then rip it hard again!❤😢
@rcsendandblast1579
9 ай бұрын
I have done a lot of testing the tank lid on the Rustler model. Wanna know what helps seal up even the ugliest lid seals. Take your tank seal out remove that screw take it out carefully clean it and add after run oil to the underside of the plastic lid and re insert the foam lid seal back in The oil will help it seal on the top of the seal like it should. 👊😎
@haywirerc
9 ай бұрын
Gotta give that a try! I saved the old seal as I felt doing some sort of trick can fix it. On mine I felt the spring was the main problem as the lid often spilt fuel when I crashed it. Thanks for the comment!
@rcsendandblast1579
9 ай бұрын
@@haywirerc You’re welcome bro. Ya man it just hit me when I cleaned the new tank and it leaked so bad you could see the exhaust coming out the lid. Since I oiled it bam fixed 👊😎
@Bullwinkle39
6 ай бұрын
You could use the trade in program to get a new engine. Then before you run it, rebuild it with stronger internals
@haywirerc
6 ай бұрын
Too late. I already bought new piston and sleeve and backplate. Maybe next time. Thank you for the help!
@Nitro_rc_life
10 ай бұрын
Hopefully it can be saved that sucks but totally not your fault
@joshherrman3201
10 ай бұрын
Damn dude. Hey man i font remember but was your 454 roto start when you got it?
@haywirerc
10 ай бұрын
No had a back plate. I swapped the crank with my spare Mach .26 crack which fits all of those big block engines.
@joshherrman3201
10 ай бұрын
@haywirerc so if I have a rotor start the pull start should have everything I need then correct? I'm slowing learning here.
@haywirerc
10 ай бұрын
Yes the pull start and rotor start will bolt onto the backplate for the pullstart/rotor start.
@TheTboyroy83
4 ай бұрын
Where did you get that cool looking fuel line?
@haywirerc
4 ай бұрын
They are fuel line covers by RC Raven. I bought it off of RC Ravens eBay account but they have it on their website also.
@TheTboyroy83
4 ай бұрын
@@haywirerc awesome thank you 👍
@Andries.Buskenz
10 ай бұрын
How many gallons you put through it? I find my trx 3.3s are anout 6-7 gallons. I always go crazy
@haywirerc
10 ай бұрын
7 quarts i have written down!
@Andries.Buskenz
10 ай бұрын
@@haywirerc thats crazy low. Shoulda been 2-3 times that easy. You may wanna check out O.S gloe plugs. Lc3 and lc4 if im not mistaken. And horizon hobby after run oil. Common mistake, you can swap things like those. Make sure you blip it or pull the starter after a few drops go in the carb. Honestly im lost for words.
@haywirerc
10 ай бұрын
I always after ran it. I think it’s from the one way bearing not being oiled. I should of used after run to oil it before I put it in. It’s a shame as that engine was in great condition.
@charlesmccardle7889
9 ай бұрын
I'm at 9 gal vp 20% still running strong with revo 2 yrs no issues. Have a new 3.3 on standby tho .
@kyronrc
9 ай бұрын
Usual 3.3 problems... these things just cant hold up. The quality of the metals is junk.
Пікірлер: 24