Nice slight of hand when the piston/sleeve leave the frame and come back with a different setup from behind the engine block. lol
@hydroracer1642
7 жыл бұрын
hey cuz u need a rolemodel in the rc world bro....next time u rebuild a motor make sure to use some atf oil to put back together it will help everything go back in nicely bro...been in the rc world for 15 yrs now and have rebuilt and resized plenty of sleave and have had engine now that have ran for over ten yrs with proper break in and after care.....nice slight of hand grabing the other piston sleave bro....lol....looks like u ran that other sleave to lean bro....that is the cause or looks like the cause of piston going throw the top....another reason your motor was cutting out could have been from the bad bearing when puting load on the motor or just to rich and loading up to much bro....not give u any beef bro just givin u a few tips....if u wanna now more and got some ? on something u need help with just shot me a im on here bro....peace cuz
@Mr.HandTunedEngines
7 жыл бұрын
hydro racer164 Yo What up. What would make u feel I don't have a role model in RC... Excedra. I have a question. I kno the answer but wonted to hear ur opinion(s) maybe you can help me out. If the instruction label on the gallon/quart of nitro fuel says after run oil is not needed why would u be using after run oil ?? I don't recall the Manuel advising to brake down engine and apply after run oil or if a individual wonted to rebuild or build a engine. Why advise me to do so. Holla bac
@godsun358
8 ай бұрын
Black Magic Magician. Dope vid 🎉how can I reshape a slightly bent sleeve? It's from a Novarossi Mito WRC 9port on road engine.
@Mr.HandTunedEngines
9 жыл бұрын
Hello Mr Just Me, Thanks for your comment. Very flattering with your choice of words. " Off camera sleeve pinch with a cheap clamp no doubt. Waste of time". I wont confirm what takes place to make these items like new. As seen only I can give these results. Call me David Copperfield... Educate your self and consider becoming a leader. One day you will come to the conclusion life is more then being negative !!! So stay off my page and save your self some time.
@Schiksie
6 жыл бұрын
Lol you....next time when you make the switch don't drop it on a metal table :-) But also David Copperfield had to start somewhere i guess.
@Mr.HandTunedEngines
5 жыл бұрын
Schiksie Trust me I'm getting better . . . lmao
@MikeKing-t9i
4 ай бұрын
BRUH got that ZULU
@frenchifab8663
9 жыл бұрын
do you have an instagram with your work on it i can follow u at?
@Mr.HandTunedEngines
9 жыл бұрын
+Izaiah Bazan No Instagram ... Stay tooned we have some plans in the works Prototype n"Effect
@randolphcatchot5421
6 жыл бұрын
Dammit I want 8 minutes of my time refunded this is horse shit...
@Mr.HandTunedEngines
6 жыл бұрын
Randolph Catchot Wow 😲 only a 8 minute refund . . . thanks for giving me some credit for the additional time I feel very proud. I was wondering about that smell you mentioned. Glad you informed it was some horse shiiiii 💩 + 👄 + 💨 = 😭 lol I was getting worried
@turbooomann
5 жыл бұрын
Nice slide of hand, i seen you pick up the engine behind the engine lol
@Mr.HandTunedEngines
5 жыл бұрын
That's whats dun in all the magic tricks right?? but we think no 1 seen what happen lol
@larrylooney4495
5 жыл бұрын
Houdini that shit was funny lol
@3rdaxis649
7 жыл бұрын
Great video. Had no idea this could even be done. Thank you.
@TheJamiejosh
7 жыл бұрын
Look up videos on sleeve pinching for some factual information. Its a simple process using a few cheap hardware items.
@jeffforbes8743
6 жыл бұрын
whole different piston and sleeve buddy.. look at the coloration on first piston how its more solid. the second piston top is less filled in with varnish.. nice try impossible to pinch a engine with ur bare hands...
@robertbruemmer3868
7 жыл бұрын
does he actually switch to a different sleeve and piston at 4:36 in the video?
@13bj
7 жыл бұрын
Robert Bruemmer your spot on dude
@Mr.HandTunedEngines
6 жыл бұрын
Robert Bruemmer Hey . . . dont come to the magic show being disruptive 😂
@Marc-hp3ne
8 жыл бұрын
if only it was this simple.
@randomness3235
5 жыл бұрын
If you kill your engine (over heat or what not) or lose compression taper in the sleeve, then all that really needs to be done to repair, is replace the sleeve? If so, to do so is by doing the reverse of your assembly steps? Is it hard to remove the sleeve? Thanks, great video.
@Mr.HandTunedEngines
5 жыл бұрын
Once the engine overheats it may cause the sleeve to warpe making it difficult to extract / remove. You can replace sleeve or find a way to make it work witch will save you a few bucks. This video was just a small piece of magic nothing to take serious.
@MikeB-wm2le
7 жыл бұрын
Just curious... where did you get your information about the way metal passes electricity through it with minerals and that it can run out of minerals? If I understood this right, at that point the metal needs to be recharged with new minerals before it can pass electricity again? I would LOVE to see the web site, book or cartoon you got THAT info from! Fortunately, you said it at the beginning so you saved me from watching what may very well be the most ridiculous video ever made.
@Mr.HandTunedEngines
7 жыл бұрын
Angryman 1001 Look it would benefit you to do your research on minerals excedra. The same with vegetables once over cooked they loose nutrient ... many chose to steam. Excessive heat will destroy !! Simple as dat.
@gavindavies2861
5 ай бұрын
Strong magnet should get that Allan ball out mate
@michaellovett2568
9 жыл бұрын
I'ma need your help rebuilding my OS 18 .... I like your videos you gotta keep them coming you can help a lot of people
@drstrange2292
7 жыл бұрын
the pinch is the tapered sleave in the cylinder and it was cause the piston to become harder to turn at tdc. once it's pass the pinch the piston can be forced back down.
@knockout35189
8 жыл бұрын
what did I just see? Magic? or was somewhere in there was how to recondition the sleeve?
@smittyb9418
8 жыл бұрын
nice vid dude...I have a lrp .30 on my savage xl...when its time to rebuild it I will be watching your vids...good job bro !!!
@DannyTv3045
9 жыл бұрын
Man I would love to be able to do that bro lol
@christianolivera3286
8 жыл бұрын
lol ya old lady wasn't having it hahaha good video bruh my man got the midas touch
@shadislandguy1424
9 жыл бұрын
Do all .18 engines use the same size piston connecting rod?
@Mr.HandTunedEngines
9 жыл бұрын
rowan frederick I haven't seen all the spec 's on 18 engines but I will say no.
@eddiemccomas519
6 жыл бұрын
you pinched the sleeve you can see the marks on it.
@Mr.HandTunedEngines
6 жыл бұрын
Eddie Mccomas I see you didn’t like my magic
@vr.vqmechanic
8 жыл бұрын
All u did was smashed the sleeve a little bit
@MrLilChilly
9 жыл бұрын
Whoodini ha ha you had me cracking up! Good vid man keep em coming
@NitroRCNerds
9 жыл бұрын
MrLilchilly Ha ha. He's greatness for sure. How's your triggy...still rockin that .23? I finally got me an Alpha (Lutz WE)....gimme a week or two and you'll see it gettin; some.
@lorenzoalonso4140
7 жыл бұрын
He got another sleeve and piston he had next to the engine block, you can see it when he reaches for something next to the engine block
Пікірлер: 49