Thanks! My Toro lost power drive with about 15 feet left on my lawn. I thought it had jumped off or jammed on the "clutch" end of the mechanism, but couldnt figure out how to get to it to fix it. You gave me the information and its running great now. Thanks again.
@tellshami
2 ай бұрын
great video-- I followed some other video and got the part from Amazon, but the belt was too tight to go on both pulleys - this video clearly explained how you can do it... thanks
@USArmy91222
5 ай бұрын
just replaced the belt on my Toro Personal Pace lawn mower with the help of this video, lawn mower is back up and running again..thank you for the very helpful video!!
@charliestoner9606
3 ай бұрын
Do you recall the specific belt you used?
@hdkevin4387
3 ай бұрын
You are very welcome!
@hdkevin4387
3 ай бұрын
@@charliestoner9606 115-4669
@JudysJack1946
7 ай бұрын
Excellent video: thorough, comprehensive and detailed right down to the wrenches and sizes required for each step.
@hdkevin4387
6 ай бұрын
Thank you for the compliment!
@deanwichert4771
Жыл бұрын
Great video especially the video quality and narration for the belt replacement including repositioning the guard. I have some tips here 1) unplug the spark plug wire whenever working the blade 2) use a vice grip to clamp the fuel line when tipping 3) adjusting the rear wheels temporarily will provide socket access to the screws behind the rear wheels for the guard 4) although not the video purpose, sharpen the blade on a grinder while it is off. Lastly, nice of you to be a good neighbor.
@hdkevin4387
6 ай бұрын
Thank you kindly for the compliment!
@avflyguy
4 ай бұрын
The blade angle should be at 35° I'v made several templates. One cardboard and one a 4" wide aluminum one
@dkupy100
3 ай бұрын
Reference #2 The oil is more of a problem. Always tip the deck carb side UP.
@sentradynamics8889
2 жыл бұрын
Thanks for listing the belt number. Was having a heck of a time finding a good number for it
@hdkevin4387
2 жыл бұрын
You’re very welcome!!
@brucewalker107
3 жыл бұрын
Thanks for the video. Yours is more helpful that the one by Toro! This is the exact configuration for my mower. I guess I am lucky that my belt had lasted 10 years. I'll throw in a couple tips. First, if you are having problems removing the side srcews for the baffle, move the rear wheel beyond the highest setting and the wheel will be out of the way. Then it's not much trouble to remove screws from both sides and get the whole baffle out of the way. My owners manual recomends tightening the blade bolt to 60 ft-lbs. This is where a 6-12 inch piece of 2x4 is very useful for holding the blade from turning while tightening/torquing as shown in the owners manual.
@hdkevin4387
3 жыл бұрын
Great tips! Everyone will benefit from them. Thank you!
@philipjohnson7029
2 жыл бұрын
This video saved me today. The belt broke half way through my cut and I didn't know what was going on. It was smoking and not propelling. Fortunately, my local hardware store had the right belt and I got it fixed in time to finish the cut. Thanks so much!
@hdkevin4387
2 жыл бұрын
Awesome! You’re very welcome!!!
@jimheiser1228
4 жыл бұрын
Thanks for the great video. Very informative and loved the trick of loosening the rear guard to turn the transmission for access to the cover versus the hassle of removing/disassembling the wheels. Big time saver.
@hdkevin4387
4 жыл бұрын
You're welcome! Glad you could use it
@ernestlefebvre563
3 жыл бұрын
I was able to correct the problems my self-propel system was having from watching this video .Thanks for guiding me through.
@hdkevin4387
3 жыл бұрын
You are very welcome! Glad I could help
@bergarama
3 жыл бұрын
I'm not a mechanic but thanks to you I was able to fix my Toro Personal Pace on my own! Much appreciated!!!
@hdkevin4387
3 жыл бұрын
Hello! You are very welcome. Thank you for the comment
@siddickramjahn2386
2 жыл бұрын
Me too. great stuff.
@fredshokoohi5912
3 жыл бұрын
Thanks, Kevin. Excellent tutorial. I have had many problems with Toro lawn equipment. They have been suffering from poor engineering.
@hdkevin4387
3 жыл бұрын
You’re very welcome!
@kevindarlington6566
2 жыл бұрын
Killer instructions - this was a massive help! Made this job a snap-thank you very much for taking the time to show this!!
@hdkevin4387
2 жыл бұрын
You are very welcome! Thank you for the comment
@wisbacks
2 жыл бұрын
Thanks for saving me a ton of time today! My belt was in good shape but somehow came off the wheel by the gear box. I honestly don't know how it worked itself off. I'm thinking a stick wedged in there just right. Long story short I disassembled just like you did and put the belt back on and reassembled. It works good again and the belt tension seems good to me! Just in case I noted the belt part number. Thanks again!!
@tjtinsurvivaltin3797
2 жыл бұрын
Bro! This REALLY helped me change my drive belt. A million thanks for posting this. I really appreciate it!!
@hdkevin4387
2 жыл бұрын
You are very welcome! Thank you kindly for the comment.
@barberdoug2012
3 жыл бұрын
Thank You! Very helpful. Don't Forget to remove the spark plug wire before starting this repair!
@hdkevin4387
3 жыл бұрын
You’re welcome! And you’re absolutely right! Big fault on my part w the plug
@glenthecarguy
2 жыл бұрын
It won't start if the bar on the handle isn't engaged .
@avflyguy
4 ай бұрын
@@glenthecarguy You really going to trust loosing some fingers based on that? If nothing else, just pull the plug wire off.
@Ragnar06
2 жыл бұрын
I didn't reed to replace the belt. Good thing, my undercarriage had the belt hood on it which it looks like you'd already removed for this video. So my fix was simply to go and loosen the transmission cable locking nut, push the transmission cable toward the engine, as you showed early-on in this video, then lock that nut back down again. I replaced the blade in the same session. It's like a whole new mower now.
@hdkevin4387
2 жыл бұрын
Awesome! Great to hear!
@Renee-qx9eo
3 жыл бұрын
Thanks, very helpful when I thought I broke my Dad's mower. Didn't need to replace the drive belt, it was just jammed with a stick, but your video really helped access the problem area.
@hdkevin4387
3 жыл бұрын
Hello! You're very welcome!
@brianboock8019
3 жыл бұрын
Thank you for this great video! It 100% help me replace the belt and figure out why the wheels were returning. All the best and thanks again
@hdkevin4387
3 жыл бұрын
You’re very welcome! I enjoy paying it forward as so many have helped me also
@Stormin_Norman
Жыл бұрын
Same model as I have and I was looking for info on this, thanks so much for the video.
@spresc2180
Жыл бұрын
My recycler was new in 2008 and to this day it starts every time on the 1st pull. Great mower/engine.
@dkupy100
3 ай бұрын
Agree but yours and mine have the old style metal carb and the one in the video is el cheapo plastic.
@UrbanGardeningWithD.A.Hanks14
2 жыл бұрын
This was exactly what I needed, thanks. The belt had gotten stuck between the pulley and housing on the back end. It was still in good shape, so it didn't need replacing. I was running over a lot of sticks when it happened, so I must have gotten a twig in there that spun it off or something.
@hdkevin4387
2 жыл бұрын
Hello. Glad you got it all fixed up!
@UrbanGardeningWithD.A.Hanks14
2 жыл бұрын
@@hdkevin4387 Yeah, I would have never figured all those parts to move, or that stupid square drive, otherwise. It took me an hour and a half to find all the right tools, and get it all apart, but seven minutes to put it all back!
@blcdad
3 жыл бұрын
Thanks for the video. I think watching it kept me from taking some things apart I didn't need to!
@hdkevin4387
3 жыл бұрын
You are very welcome!
@carlwarsing4899
3 жыл бұрын
thank you for the helpful video - saved me from going to the mower repair
@hdkevin4387
3 жыл бұрын
You are very welcome! Glad it was helpful
@tinman143
Жыл бұрын
Great video I replaced my belt a few times and this is the best video...THANK YOU!!
@ChasedRabbit
2 жыл бұрын
Great video! Thank you so much for putting the belt part number in the description!
@hdkevin4387
2 жыл бұрын
You are very welcome!
@scottmcculloch7685
Жыл бұрын
Thanks so much for this video! and a second thanks for including the wrench sizes! Mower is running like new thanks to you. Much appreciated!
@greggfowler1443
7 ай бұрын
Thank you . I just learned what I was not doing to get the belt straight . I needed to move that guard . 👍
@hdkevin4387
6 ай бұрын
You are very welcome!
@raychapman1134
2 ай бұрын
You are my hero for this damn video lol. Made my life easier, which is the best thing in the world.
@raynickerson2133
2 жыл бұрын
Going to use this tomorrow. Real pain in the neck without power wheels. Thanks
@hdkevin4387
2 жыл бұрын
Great! Hope it worked out ok
@jlewis5036
3 жыл бұрын
Great video very helpful. If it wasn’t for your help I wouldn’t have just mowed my lawn after a week and a half! Thanks
@hdkevin4387
3 жыл бұрын
You're very welcome! Glad I could help out!
@mi_cheap_guns2925
5 ай бұрын
Thanks for the video! These lawnmower videos have really helped. Some of your up close shots are great. The belt isn’t my problem, but still helpful. My personal pace quit working, too. Looks like that black bracket on the gear box that the spring on the end of the cable is attached to isn’t attached anymore. Looks like the bracket is the only thing moving when I move the handle, not good. Going to have to find another video to see how the bracket attaches to the trans and why mine isn’t attached anymore. Thanks, again!
@TomGallagher-xo6vb
Жыл бұрын
Thanks man. Great video and saved me some money. My belt fell off but it is a little loose so may need to replace in near future but this was very helpful. Thanks again!!
@amosdiaz2704
Жыл бұрын
Thx .. I have that exact problem .. now I can try my mower
@vickischenher2722
3 жыл бұрын
Great informative video. I am confident I can do this myself now. Thanks for sharing.
@hdkevin4387
3 жыл бұрын
You're welcome. Thank you for the comment!
@skibum1610
3 жыл бұрын
Very helpful used as a guide today and my mowers back working perfectly thanks!!
@hdkevin4387
3 жыл бұрын
You’re very welcome! I’m happy to pay it forward
@hrhufnstuf261
2 жыл бұрын
Thank you! Storage over the Winter must have loosen the nut on the cable. I had the handle and with a few spins I was back in business.
@hdkevin4387
2 жыл бұрын
You’re very welcome! Glad you got it squared away for free!
@JoseSanchez-wb5rz
3 жыл бұрын
Glad I went for the FWD version of this machine,seen a lot of videos of the RWD with a ton of different problems and they usually require more work and more parts.
@hdkevin4387
3 жыл бұрын
Does it propel effectively? Are you satisfied?
@JoseSanchez-wb5rz
3 жыл бұрын
@@hdkevin4387 Yes I am satisfied with the machine and it does propel very good wouldn't know how good it would be on a hilly property but for flat yards like mine it actually gives me a workout.
@hdkevin4387
3 жыл бұрын
@@JoseSanchez-wb5rz great to hear!
@tedjasiewicz514
3 жыл бұрын
Excellent instrucional video ! Thank you Ted Jasiewicz
@hdkevin4387
3 жыл бұрын
Thank you. You are very welcome!
@John-e3h8r
6 ай бұрын
Man this was a ton of help 💯😁
@hdkevin4387
6 ай бұрын
You're very welcome!
@Aspirintax
5 ай бұрын
I don’t own this exact model, but someone stole the design from someone. I have the Briggs and Stratton version of this design. Thanks for the video.
@dkupy100
3 ай бұрын
The decks are all Toro.
@bobvanwest
3 жыл бұрын
Great video. Of all the wrenches I have, not one 3/8, had to use my long needle nose. Works great now.
@hdkevin4387
3 жыл бұрын
It’s probably hanging out with all your missing 10mm sockets. Ha ha
@bobvanwest
3 жыл бұрын
@@hdkevin4387 That is true. I did spend a day organizing my tool boxes and bags and of course I found the right sockets. So next time I will know better. It's been about 2 weeks since I replaced the belt, and it's working as expected. Thanks again for the video.
@hdkevin4387
3 жыл бұрын
@@bobvanwest Great news! Thank you
@ickess
2 жыл бұрын
This was a very helpful video I did a little motion sickness from the Camera moving around a bunch. It could’ve been me though with the lawnmower cocked on an angle and some gas dripping out I might’ve gotten a little dizzy from that haha
@jcstevensva
2 жыл бұрын
Great job on that. Thanks a lot. Will see what else you did on the 20332. Hoping you changed plugs, air filter, and any thing else needed when mower is hard as heck to start. I have my second one of these mowers and they are terrific. But, get hard as heck to start even on warm day.
@wisbacks
2 жыл бұрын
Interesting. Mine worked flawlessly for probably 5-6 years but all of a sudden mine has started giving me problems when starting at times. When I bag the grass I'm stopping numerous times to empty the bag. Sometimes starts on the first pull and other times it will take 3-4 pulls. I can't put my finger on it. It's like it gets a little flooded. I've got the 20334 model which looks almost identical to the 20332.
@airmaster5691
Жыл бұрын
@@wisbacks Take your fuel system apart from the gas tank hose to the carb and clean it thoroughly. Use a very small wire to clean the ports on the carb. What works best is the wire that comes wrapped around a bread loaf. Strip the colored part of it off to get to the wire. Also get one of those small fuel filters and a couple of clamps and install it in your fuel line. Change it each year and it will solve a lot of starting problems. I've been there done that a couple of times with my Briggs engine on my Toro.
@cdf964
Жыл бұрын
Thanks for this very helpful video.
@robertcrain4428
3 жыл бұрын
What Robert Blake said. If you have a lot of junk( sticks, rocks, etc.) sooner or later something gets between belt & pulley. Takes less than 1/2 hour to put on new belt with this video.And that’s the first time !
@hdkevin4387
3 жыл бұрын
Very true!
@warsteiner75
Жыл бұрын
Excellent video, thank you so much for the break down.
@avflyguy
4 ай бұрын
That was very helpful. Have new belt and new blade going on my 4 yr old Toro PP Lawnmower. Am sure I could have figured it out, but like the way you didn't have to take rear wheels off.. Probably not a bad idea anyway to grease those gears up. Now, if you can figure out how to keep from wearing out a $60 grass catcher, that would be nice. They last about 2 years for me.
@BigChristopher
3 жыл бұрын
Nice video Kevin. It can be a challenge to do things one handed and film. Keep up the good work!
@hdkevin4387
3 жыл бұрын
Thanks!
@undrtakr2222
3 ай бұрын
Ok, here is some critical information, for those of us, with an electric/pull start system, and the black battery box on the deck of the mower. Ok, YES, there is a bolt underneath the box. But, it is towards the back of the mower, and you will see a slightly raised section of the box, that does not touch the deck, but sit's above it, about 1/4-3/8". The bolt you have to access is, literally in that notch, towards the backside of the black box/mower. And, I have found, that the box is riveted to the deck. So, for full access, you will have to rip the box off of the top of the deck, revealing 2 of the 3 bolts, as the 2nd bolt is, along the left side of the black battery box, just underneath the side front corner. But, if you are able to remove all of the plastic covers off of the back, including the flapper, for the bag. As, the top of the flapper for the bag hatch, is literally what has you blinded from seeing the bolt in the first place, besides the battery box itself. And, since I can't start it with the key anymore(Long story short, the cable harness was ripped out of the key starter switch, and ruined it), so it's pretty useless to me, at the moment. So, I decided to just rip the black box itself off. Which, made it much more simpler to access all 3 bolt's, for the plastic belt guard underneath. Also, it is a good idea to take a plastic bag(Walmart bags will do fine), and use it underneath the gas cap, by taking the cap off, then draping the bag(Double layer, by using whole bag) over the open hole, then screw the cap back on, and you now have a sealed gas cap, from leaking...
@lenwoodlloyd292
Жыл бұрын
Excellent video
@undrtakr2222
3 ай бұрын
Word of advice, to not have to fight with that spacer, just use a bit of grease on the backside, that is closest to the blade, as it act's as a suction cup, to hold it in place. While, not making it a permanent fix to the bottom of the cylinder it sit's in...
@lawrencehulsbrink6224
3 жыл бұрын
Great video. First safety step not mentioned:Step #1... remove spark plug wire anytime working around mower blade.
@hdkevin4387
3 жыл бұрын
My father always told me that too. I failed him! Ha ha
@lowiqsavage
2 жыл бұрын
don't forget safety glasses, gloves, earplugs and a giant insulating suit... ;)
@emeraldlawncare7002
2 жыл бұрын
Great video. Thanks
@hdkevin4387
2 жыл бұрын
You are very welcome!
@mikehrdlicka8635
Жыл бұрын
I turn wheel height adjustment to access the shield bolts
@FRANKLAURA100
5 ай бұрын
Thank You! Very helpful.
@Irwhodunit
3 жыл бұрын
Hey, everybody, here's a hint. Rake and pick up sticks that fall out of trees. They seem to cut or mulch easily, but a chunk the size of a short pencil can ruin a belt if it gets stuck in the pulley.
@LANELIFEburgundy
4 ай бұрын
TOUCHDOWN!!!!!!! Thank u real good😊
@jordanjonz
Жыл бұрын
Thanks for the help brother! Same issue that happened to mine
@bradbarthold1278
Жыл бұрын
Did you have any trouble getting the belt cover back on because I can't get mine back on. I can't get the screws to line up. Do I have to take the blade off in order to get it on
@mjg263
4 жыл бұрын
Nice job! Those newer style gearboxes are much easier to change belts on than the old aluminum ones. Weird that it chewed the belt up so soon.
@hdkevin4387
4 жыл бұрын
I agree. It must have been out of adjustment
@rickjames6948
3 жыл бұрын
A new OEM Toro drive belt is puny to say the least. No wonder they don't last. These are junk mowers.
@joebubbit
Жыл бұрын
Wish I saw how you got the spring out.
@jacobvision17
2 жыл бұрын
The repair description is great. There is a repaired model. Broken rear pivot arm nut hole. How can I fix it? No matter how much I search on the internet, I can't find the part. please. (model 20340 (7.25/163cc)
@philherrick7319
Ай бұрын
Drawing in the manual looks like the cable setup for AWD self propel
@miltonaguilar3732
3 жыл бұрын
Thanks for this video!
@hdkevin4387
3 жыл бұрын
You are very welcome. Thank you for your comment
@leekumiega9268
2 жыл бұрын
I have a 28 year old Lawnboy Gold series made by Toro where the entire belt is on the top of the deck . The belt and the 3 speed transmission have never failed in all that time and I cut a 1/4 acre once a week. Why can't they make them like that anymore? Planed obsolescence ? Except for cleaning and greasing the small drive gears so they will slip when going backwards and replacing the wheels when they wore out and split the drive train has been trouble free. What recently failed the blower housing from metal fatigue where it bolted to the engine from so many pull starts and I replaced the pull cord itself once.
@hdkevin4387
2 жыл бұрын
You’re absolutely right. They don’t make money on things that last 20 years
@Round2Dad
3 жыл бұрын
Very good video. Thank you.
@hdkevin4387
3 жыл бұрын
You are very welcome. Thank you for your comment!
@grounded-b937
Жыл бұрын
Looks like someone was in there before. There are heat stains from welding, on the blade adaptor.
@BlackNAVYAmericanVET
3 жыл бұрын
Thank you, thank you, thank you 🙏🏽
@hdkevin4387
3 жыл бұрын
You are very welcome!
@tedibare1
2 жыл бұрын
My mower is 11 yrs older but built the same way
@j.g.534
3 жыл бұрын
Awsome tutorial thank you
@hdkevin4387
3 жыл бұрын
You are very welcome! Thank you
@jmabs5096
Жыл бұрын
5:53 why they used square screws are beyond me. They will be stripped by 2-3rd belt change. I've only changed my belt once on my 2010 toro recyler 20332
@3636lk
2 жыл бұрын
Just as I was finishing my front yard the mower self propel stopped and there was like a screaming when I would try to engage it, I'm thinking something's going on with the belt. Hate to tear it apart but looks like I got to. I'm hoping your video helps. thanks Kevin
@hdkevin4387
2 жыл бұрын
It’s not too bad! I just blindly started digging in there and it was quick and easy. You got this
@3636lk
2 жыл бұрын
@@hdkevin4387 sure hope so, thanks Kevin
@rhintas
Жыл бұрын
PERFECT !!!! thank you so much !!!
@hdkevin4387
Жыл бұрын
You are very welcome. Glad it helped!
@llamacebu216
Жыл бұрын
Be sure to check your model # . This belt is for 2009 and up. Just drove myself crazy for 2hours wondering what's going on bc I needed a bigger 91-2258 belt is about 2" bigger
@williaml2822
27 күн бұрын
Can you work on one of these in the Stow position which would give full access to the underside of the mower?
@mauroavalos558
3 жыл бұрын
Very helpful
@hdkevin4387
3 жыл бұрын
Thank you!
@harryharry3193
4 ай бұрын
nice job!
@hdkevin4387
3 ай бұрын
Thank you!
@syrusmcneil3298
3 жыл бұрын
Hey You Can Move The Rear Wheels Up And Down To Get To The "Bolts"
@hdkevin4387
3 жыл бұрын
Thanks!
@rickjames6948
3 жыл бұрын
I took an allen wrench and ground it square to get the transmission screws off that cover. Great idea Toro for using square headed screws LOL.
@hdkevin4387
3 жыл бұрын
I know. Path of least resistance for these manufacturers....
@jasonrozell9132
3 жыл бұрын
Most all multi-bit tools have several square head bit included. Not a real hard to find bit
@immaterialblonde4066
3 жыл бұрын
Square 'Robinson' heads are not a hard find. A square recess is a good choice here because the recess goes deeper than with the more popular screw drives. This means you can apply a decent amount of torque to undo stubborn, crudded up screws, without risking 'cam out'. Clean out any grass from the recess first, to ensure you make use of the full depth. The Pastite thread is also an interesting choice, given the screw doesn't thread into plastic. Perhaps it was chosen to help resist vibration loosening.
@hdkevin4387
3 жыл бұрын
@@immaterialblonde4066 Very good point
@sofias_world5320
2 жыл бұрын
Nicely done
@hdkevin4387
2 жыл бұрын
Thank you!
@robertpapps3618
Жыл бұрын
Looks easy, thanks much!
@hdkevin4387
Жыл бұрын
You are very welcome!!
@airmaster5691
Жыл бұрын
Thanks for the video. I have a personal pace from 2015 and the belt just now needs changing. But...there is no way that can be the correct blade for that mower. It should fit the entire width of the holding carrier that it sets in. That blade looks to narrow.
@shelleygilmore3923
2 жыл бұрын
Super helpful! Thank you! 🙂
@barnettandrews8260
2 жыл бұрын
How do you check transmission on self propelled mowers
@natureandrandomstuff
4 ай бұрын
Is there a way to adjust the belt. I bought a new one because the existing one was lose, installed the new one but still seems lose to me
@hdkevin4387
3 ай бұрын
Hello. I am trying to remember but I think you can tighten up the threads on the spring for the personal pace bar
@bradbarthold1278
Ай бұрын
@hdkevin4387 so to tighten the belt you use the same knob that you would use to adjust the self propel?
@edwardsoffy-girl2166
2 жыл бұрын
Thanks to your video I was able to change the belt on my Toro 20332 Self Propelled mower. Now, the back wheels run by themselves and much too fast. I tried adjusting the wire on the side handle both ways and the mower still wants to run by itself. What am I missing? Is it possible I stretched the cable when I struggled to put the spring back on? What would cause the wheels to run by themselves?
@hdkevin4387
2 жыл бұрын
Hello. You’re very welcome. It means the belt is too tight. Well the cable could be pinched if you had to struggle with it. Does it move freely back and forth? Also could the belt be the wrong size? If it’s too small it will bite on the pulley even if not engaged. Could the spring be misaligned perhaps?
@wisbacks
2 жыл бұрын
Wondering if you got this figured out? I literally just did this today. I'm wondering if maybe the wire going to the gear box got kinked making it shorter and and in rest position the drive is already engaged. I know getting that spring reconnected was a pain in the butt for me!! I would watch the part again where he reconnects the spring to make sure the position is correct. I know I made a mental note of that when I was reassembling.
@michaelwas8549
2 жыл бұрын
I got mine on without taking anything apart on the drive side. Kind of a bear to get it around the pulley but it is possible.
@hdkevin4387
2 жыл бұрын
Good to know. Thank you!
@dblaylock22
2 жыл бұрын
My belt keeps coming off on the drive cable end of my 20332. I’ve tried two new different belts. The last one I tried was toro original. Any tips on how to fix this?
@Rick-tb4so
2 жыл бұрын
Great video....is it worth replacing the spring ??
@hdkevin4387
2 жыл бұрын
This spring seemed ok. But while you’re in there never hurts
@caseykittel
Жыл бұрын
Thanks. I was wondering about greasing the rear drive system. Any pointers? I’m getting some grinding when I try to go up big hills. Both drive wheels have good gears, so I’m thinking it’s a dry ratcheting mechanism somewhere.
@michaeljdestefano1208
2 жыл бұрын
Video was excellent!! Thank you. By any chance do you know the Belt Length. I put a 3L350 on my mower and it's way too big.
@hdkevin4387
2 жыл бұрын
You are very welcome. 3/8 x 33.25”circumference
@bigjoe8922
2 жыл бұрын
Thank you
@hdkevin4387
2 жыл бұрын
You are very welcome sir
@bradbarthold1278
Ай бұрын
How do you tighten the belt on this type of mower?
@RB-re5es
2 жыл бұрын
You didn't show how to adjust the drive cable.
@hdkevin4387
2 жыл бұрын
I didn't realize that. I think it was on my mind and once I found the problem I didn't need to adjust it
@susan5301
3 жыл бұрын
That's exactly what happens to mine quite frequently! I always thought Toro was a good brand but now I wonder! The repair shop charges me over $60 to pick it up and replace the belt it. Gonna look for something else. Any suggestions please?
@hdkevin4387
3 жыл бұрын
I can only think a component could be bent that is causing contact to the belt? I adjusted the belt guard under the mower deck and it hasn't had any problems since. Did you do your last repair or did the repair shop perform it?
@susan5301
3 жыл бұрын
@@hdkevin4387 Hi Kevin, thanks for answering back! I don't know anything about lawnmowers so the Toro guy in my town picks it up, charges me for that and for repairing. It's only 3 years old and last summer he claimed the transmission went out and that was almost $400! I don't want to put any more money into it, so I'm kinda stuck.... Thanks for your help!
@hdkevin4387
3 жыл бұрын
@@susan5301 you’re welcome! I have a lawnboy that has been excellent the last 10 years. It doesn’t have the personal pace, but it has been very reliable
@rhalama1
2 жыл бұрын
@@hdkevin4387 if you have a small yard 1/4 or less i would suggest a Ego battery mower. Cost about $ 500 but i've had mine 5 years and zero problems. No gas to buy or store. I love it.
@hdkevin4387
2 жыл бұрын
@@rhalama1 that’s definitely the way to go!
@barbaraadams8219
3 жыл бұрын
Thanks. Wish you were my neighbor.
@jmabs5096
Жыл бұрын
9:58 move the wheel all the way up or down I forget which way, you can get easy access to that screw
@markphillips6154
3 жыл бұрын
We have an older Torrell probably 15 years old. It’s a little over engineered. Had to takeoff nine different pieces including the wheels to get the belt off. It’s a monster
@mks2715
3 жыл бұрын
I loved the information (time saving) and your audio (explaining)! A lot of the time your subject in the video was just out of view!
@hdkevin4387
3 жыл бұрын
Thank you! I didn't have my regular camera which has a screen on the back so I was guessing most of the time as to what I was filming. Ha ha
@meta460085
3 жыл бұрын
Thanks for the video, I found it after I had already replaced my slipped and chewed up belt. I replaced belt with identical OEM belt and it lasted about a month and new belt slipped off again, what should I be adjusting to increase tension of the new new belt before I replace it again?
@imaxfli
3 жыл бұрын
Yea...wheres this reply?
@peoplepower1272
2 жыл бұрын
Simple...the pulleys are worn so even a new belt runs looser than it should. The pulley on the mower shaft takes most of the wear so replace it (about $25) and this should help eliminate the problem.
Пікірлер: 273