I installed the yellow Noble Lux LED fog lights on my '24 VB WRX over the past weekend to replace my OEM white light fogs.. I did use the OEM fog light bracket. Pretty decent light output from the Noble fog lights.. pretty happy with them!
@ianfairbanks1318
Ай бұрын
It just cracks me up tha tsomeone would use this Cheesy chinese wire harness, fuse holder, and relay, when ALL of these components are already on the cars. even the base model. All you need to add is a panasonic relay and a factory fog light switch.
@toyosup88
Ай бұрын
I’m sure they will come out with an updated kit with all that after everyone buys this one 😂
@ianfairbanks1318
Ай бұрын
@@toyosup88 especially after I did all of the hard work for them
@carbon9652
26 күн бұрын
I personally just went ahead and just cut the stock clip that’s under the dash that requires the activator fuse and just soldered it together nothing else and it work just like OEM no extra wires.
@ianfairbanks1318
Ай бұрын
My man, i just installed this same kit on my base VB. Let me make your life easier. Use the stock wiring that's already there. You need to buy a panasonic relay that's $13 from Mouser electronics (PN# ACVN51212), and an OEM Subaru Foglight switch ($70) PN#H4510FL500. Plug the stock harness into the foglight switch (Use the directions from the oem foglight kit) plug the Panasonic relay into the fuse box on the passenger side. LMK if you have Q's.
@michaelrivera3688
13 күн бұрын
Hey man, how did you handle the DRL activator under the driver side dash? The subaru DRL kit comes with the fuse but its not sold separately.
@ianfairbanks1318
12 күн бұрын
@@michaelrivera3688 Just chop the harness and splice the two pink wires together. its LED, so they don't pull a lot of volts. if the wiring were severed (crash or deer.) it would take out the fuse in the fuse box that's already there.
@michaelrivera3688
12 күн бұрын
@ianfairbanks1318 thanks homie, I'm surprised no 3rd party vendor has made this adapter. Would simplify the fuck out of everything.
@ianfairbanks1318
11 күн бұрын
@@michaelrivera3688 I was searching SoA's website for a similar style plug that i could put a jumper into and sell. Can't find it. It only comes as a complete wire harness.
@prognogg212
11 күн бұрын
when connecting the red and black wire to the battery, did it matter which one you did first? Did you disconnect battery ground before doing everything?
@N1ghtwolfuniverse
Ай бұрын
Why not just use the factory harness that is already installed on vehicle??
@ImportImageRacing
Ай бұрын
Do it.. Nobody’s stopping you!
@prognogg212
7 күн бұрын
how in gods name did you make that pass through under the dash in the grommet???? this is next to impossible
@prognogg212
11 күн бұрын
You also show a picture and explain you mounted the relay to the battery hold down, but I don’t understand how you did that. Isn’t there a relay box on the left side of the engine bay by the abs?
@marioc6744
Ай бұрын
What's the best way of getting the clutch grommet back in place. I have it pushed inside but finding it impossible to push it back in place.
@bradthornton6953
Ай бұрын
Use some soapy water in a spray bottle, it will provide some lubrication to get the grommet pushed in. Silicone spray would work as well (and better) but can be smelly if some gets into the interior of your car.
Пікірлер: 17