Could you please describe particularly interfacing with the BMS system, it's very important bcz most of the technicians don't know about it
@makofficialvlog2676
Жыл бұрын
Good job..
@channaransilu5066
3 жыл бұрын
Good job sri ...thanx..
@foyzulislam9975
Жыл бұрын
Thanks
@gajindrakc8337
Жыл бұрын
good work
@fktv9888
4 жыл бұрын
Good job
@achhistory5112
2 жыл бұрын
Super bro great job thanku
@foyzulislam9975
Жыл бұрын
Thanks
@user-id3zw7ss7o
10 ай бұрын
❤❤❤❤
@jahangiralam5266
2 жыл бұрын
tnx broo
@foyzulislam9975
Жыл бұрын
Thanks
@edgarbonto439
2 жыл бұрын
You are very good at this i wish i have your skill
@foyzulislam9975
2 жыл бұрын
Thanks
@foyzulislam9975
Жыл бұрын
Thanks
@getnetyilfu3148
3 жыл бұрын
Nice training i appreciated you, how i can connect high pressure and low pressure switch it is not clear to me please
@shbhd5832
2 жыл бұрын
Nice
@foyzulislam9975
Жыл бұрын
Thanks
@najamahamad5411
2 жыл бұрын
Thanks khudahafij
@foyzulislam9975
Жыл бұрын
Thanks
@muhammadsufyan3214
2 жыл бұрын
AsSalam u Alikum i am from Pakistan
@muhammadsufyan3214
2 жыл бұрын
can u help me
@foyzulislam9975
Жыл бұрын
W/s. I'm from Bangladesh
@maidulislam1429
4 жыл бұрын
Good job bro
@foyzulislam9975
4 жыл бұрын
Thanks bro
@foyzulislam9975
4 жыл бұрын
Thanks
@zoumanasamueldiarra9702
3 жыл бұрын
My question is about the actuator plug. Why when you check the voltage with connected on actuator you get 24V dc??? But if you put back on actuator there are no voltage
@pomekhan5923
4 жыл бұрын
Great training
@foyzulislam9975
4 жыл бұрын
Tnx
@wefindThem
2 жыл бұрын
Thanks for your good information but I have some confusion about this panel,details given below. 1. Key Suppression disconnect switch , where I connect this switch in panel and how? 2. 1st & 2nd stages what about this, normally we need to loop with NAC 1,2,3? 3. How I can interface with fire alarm system for trouble & fire. Please give me solutions.
@foyzulislam9975
2 жыл бұрын
Thanks for your comments Check the below mentioned Ans 1. If you are use separate disconnect switch. Just connect in the panel Extrac options to disconnect switch and from disconnect to Ivo or aerosol generators. If you want to Use in the panel auto and Manuel key for the disconnect switch , you can use. Just bring the cable from ivo or aerosol connect back side of the auto and Manuel key then from auto & Manuel key to connect in Extract Com. & NO. 2. 1 stage & 2nd stage you need to use for sequence operation. NAC 1,2 to 1&2stage and Horn strobe bell need some wiring. 3. Trouble, First alarm & Release you can connect direct in the panel. For 2nd alarm you need to make waring. You have to provide 24vdc relay.
@EFYCOMMS_TECHNOLOGIES
3 жыл бұрын
Good morning from nigerian i need a technical support i want to connect 5 sigma xt fire suppression panel together does it have the feature and what terminal that accept the connection
@kashifzulfiqar5907
5 ай бұрын
How much ohm resistor attached for manual release pull station with positive
@franconap2871
Жыл бұрын
good day sir.can you please make video on how to connect access door to a conventional fire alarm control panel .thank you sir in advance.
@nazruellah4661
Жыл бұрын
Assalamuaikum..... Sir, I have a panel like that but it always makes a sound bib bib bib... then the indicator shows a yellow light on comms fault... can you please help sir what's the problem...? please sir I hope for your answer... Thank you Sir Barakallah fii umrik
@najamahamad5411
2 жыл бұрын
Asalamalekum Nice training You video help me
@foyzulislam9975
2 жыл бұрын
Thanks
@najamahamad5411
2 жыл бұрын
Asalamalekum How are you. Sir
@foyzulislam9975
2 жыл бұрын
W/C fine and you?
@losta7008
2 жыл бұрын
Regarding low pressure switch, after dischsrge, is the panel still indicating trouble ? Or it will stop lighting in the board of the panel?
@foyzulislam9975
2 жыл бұрын
After discharge continue panel showing indicate low pressure trouble..
@losta7008
2 жыл бұрын
I recognize that some panel termination of the low presdure switch has a resisor with cable and some does not have. Is there any clarification for that? Or it depend in the type of panel?
@foyzulislam9975
2 жыл бұрын
It depend inthe type of panel
@foyzulislam9975
2 жыл бұрын
But resistance should be connect in the Low pressure EOL.not in the panel
@youngmindsET
Жыл бұрын
I have been installing the sigma A-XT suppression FACP, but when I tried to enter level 3 programming the control panel continuously beeps and general fault led lits, even if I pressed the mode button I could not able to program it. please give me a suggestion on what shall I do?
@foyzulislam9975
Жыл бұрын
kzitem.info/news/bejne/xGZ3rXWArqJzf3Y
@ngangmaxcelous6057
3 жыл бұрын
I did not really understand how to contact from the cylinder to the mother board sir
@makayafrancis6101
3 жыл бұрын
Good day men I got a small problem to set up my fire Panel
@foyzulislam9975
Жыл бұрын
What happen
@Mrkhan-ru2tc
6 ай бұрын
Hindi me bhi vedio banaya karo yar
@najamahamad5411
2 жыл бұрын
Asalamalekum sir
@foyzulislam9975
2 жыл бұрын
WC
@marvincurimao1600
Жыл бұрын
manual only ..means manual release at smoke it will not work.. only mechanical release from cylinder will work
@al_up61
10 ай бұрын
How to solve power troubles problems?
@waqasahmad9033
4 ай бұрын
disable switch is on falt release trouble is off after no falt problem you solved
@mdsajidalam6068
2 жыл бұрын
Bhai Novec system 1230 faulty trouble moniter how to Remove
@juliushobbies8858
4 ай бұрын
How to remove that releasing trouble
@gidrafngugi3913
4 жыл бұрын
I have a question am one site there are using the aerosol system any heads ups
@gidrafngugi3913
4 жыл бұрын
Can you connect the do not enter direct in the panel without relay
@foyzulislam9975
4 жыл бұрын
Of course! Before install aerosol generator u have to make sure temperature of aerosol generator. And distance from materials to generator . Bcz aerosol generator is more sensitive, check the type of generator & temperature. Then check the Proper excess from Aerosol generator to materials.
@foyzulislam9975
4 жыл бұрын
No, for do not enter we need to provide additional 24 v relay
@gidrafngugi3913
4 жыл бұрын
@@foyzulislam9975 okay thanks tomorrow I be doing the termination for the panel I come around for more knowledge thanks
@foyzulislam9975
4 жыл бұрын
kzitem.info/news/bejne/0Y1mvmxrqmmDrZw Click here for details of aerosol generator
@masumhossain5966
Жыл бұрын
Please sir FM 200 panel wiring connection in bangla please please please
@saifrohad6297
Жыл бұрын
Panel buzzer is not working how can i disable the beep beep sound
@Muthu-cs4wj
3 жыл бұрын
Pfc potter panel programming method
@foyzulislam9975
Жыл бұрын
Coming Soon
@mohamedyousuf8519
3 жыл бұрын
Sir relay contact 24v and bms ,scader and diesel cut off control how to connect pls relay number 24v + coil 14 and 13 and -use as common plse explain relay number
@foyzulislam9975
3 жыл бұрын
Which signal u need to diesel cut off control????
@foyzulislam9975
3 жыл бұрын
If you want 1st signal it should be Cut so you have to connect one wire in relay com and No. Coil 13 connect auxiliary + wire coil 14 connect 1 st alarm options No wire. And Auxiliary - one wire connect in 1st alarm common options
@bapipaul8786
Жыл бұрын
How to remove and refile novec1230
@prasadp8308
2 жыл бұрын
How to remove Releasing trouble?
@foyzulislam9975
2 жыл бұрын
Check the diode connection (+&-).
@jommelvictoria9693
2 жыл бұрын
Sir can you help me. I have same control panel you have fm200 supression i have problem in the nac i already terminated the bell on nac1 and i have also have detectors in zone1 and zone2 but when i try to activate the detectors its shows on panel only zone trouble, and also the the bell was not activated can you help me about the termination about this thanks in advance
@foyzulislam9975
Жыл бұрын
Connect in 1 stage. You need to wiring some cable nac to 1 stage then it will be work
@jommelvictoria9693
Жыл бұрын
@@foyzulislam9975 i will try sir i hope it will work thanks
@jommelvictoria9693
Жыл бұрын
O tried sir but when i put the positive in nac 1 and the negative in stage 1 the panel show fault in nac 1
@foyzulislam9975
Жыл бұрын
In nac options you have to use 10k Resistance then trouble will go... Bell negative wire connect in nac and nac to 1 stage com loop 1wire and in No connect bell positive wire...
@masumhossain5966
Жыл бұрын
Are you Bangladesh
@foyzulislam9975
Жыл бұрын
???
@najamahamad5411
2 жыл бұрын
I am working Fm 200 fike compuny panal Sold
@foyzulislam9975
2 жыл бұрын
Good job
@makayafrancis6101
3 жыл бұрын
How can I get you ? for assistance
@foyzulislam9975
3 жыл бұрын
You From????
@renanemohamed7071
7 күн бұрын
Hello can you send mi wiring diagrame of this panelle .vidéo at .7.56 minutes pleas sir
@foyzulislam9975
6 күн бұрын
let see
@nafisaiqbal5814
Жыл бұрын
Where will be BMS tarminetion??
@foyzulislam9975
Жыл бұрын
BMS should be connecte to its relay
@rickyvergara1497
2 жыл бұрын
Have option for DO NOT ENTER USING PANEL ONLY
@foyzulislam9975
2 жыл бұрын
No
@afrozahmad5926
3 жыл бұрын
I am afroz ahmad please sir give me wairing diagram all part and all relay wairing diagram thank you
@foyzulislam9975
3 жыл бұрын
ok
@honestboy4976
Жыл бұрын
I am Shabab Alam I need wairing Diagram with All fire system Equipment ex. Smoke detector mcp sounder hell horn etc all 24vdc relay only Fire suppersion system FM200
@syedrehan3238
3 жыл бұрын
hello brother on zone activation abort switch is not working and it not hold the count down timer is there any programming for abort switch
@foyzulislam9975
3 жыл бұрын
Did you check the time delay programming number???? Just press the Lamp button and check the (-) options then set the time delay -30 second.If it’s not work plz send to me your programming number then I can rectify. Why it’s not working. Thanks for your comment
@foyzulislam9975
3 жыл бұрын
kzitem.info/news/bejne/xGZ3rXWArqJzf3Y Plz check this video
@syedrehan3238
3 жыл бұрын
@@foyzulislam9975 yes its -30 time delay only
@syedrehan3238
3 жыл бұрын
@@foyzulislam9975 i already checked this video also but same issue while push and hold abort switch count down are still not stop
@syedrehan3238
3 жыл бұрын
can i get your contact no
@mdsajidalam6068
2 жыл бұрын
Sir please give me the Answer of Question
@EFYCOMMS_TECHNOLOGIES
3 жыл бұрын
I will also need your email address i need technical support i like your work
Пікірлер: 115