I had no idea this stuf existed. Those are neat ways to solve the problem. I'm still working on my 1/32 tire balancer...but it's hard to keep those teeny weeny wheel weights stuck to the rims.....lol
@slotcarazing
2 жыл бұрын
Using foam inserts is pretty much standard practice for the DiSCA digital races that are run mostly on Ninco tracks. Worth mentioning rules don’t allow tyre glueing and use hand-outs for everyone. Of course there are some plain rib wheels on some DiSCA race cars but it’s pretty commonplace to see the foams in use.
@_Dave_S
2 жыл бұрын
My track is very small too, so I might get some of the sponge inserts for my NSR cars and see how it goes. Thanks for the info Harry!
@Homeracingworld
2 жыл бұрын
Good luck hope it works formyou.
@keithfilkins2043
2 жыл бұрын
Thanks Harry
@norbertjillich768
2 жыл бұрын
The car looks sponge worthy. LOL!
@RacerX888
2 жыл бұрын
Great video. I was wondering about this exact thing as I am new to slotcars but have lots of RC race and drifting experience and the air system tires don't seem to make sense to me. "Air" tires with no way to seal in the pressure would be like racing on a half flat tire, however I will know more when my first NSR car gets here this week and I will be doing this to the rear tires right away. I think you can also use a rc tire foam insert cut to size and 4mm double sided electronics repair tape, which is the slim double sided tape on bar type slot car magnets like from Revoslot. At least that's what I'm going to try as I don't have access to a local slot car shop with foam inserts or tires.
@MrDarrenp40
2 жыл бұрын
Thanks - I think we got two tenths out of this which on your fine circuit equates to a 5% improvement in performance. Not bad for a bit of foam.
@modelracecar
2 жыл бұрын
Welcome to full contact patch...I'd love to see you fit a set of non-air wheels and do the test again, I've long been an exponent of non-air wheels, air wheels for me feel as though the centre of the tyre 'folds under' in corners causing the rear to hop.
@johnd8892
2 жыл бұрын
Only caught a glimpse of the make of the foam inserts. Are Thunderslot the only source of ready made foam inserts? I am convinced that something like the foam inserts are best for even the largest routed wood tracks I race on. This is also within the spirit of our rules of staying with standard car gearing and tyre size by not arranging for this to change by tyre expansion at speed.
@Homeracingworld
2 жыл бұрын
Just hit pause? #RMRFM001
@pjwyman1971
2 жыл бұрын
Do NSR make the foam inserts or is it just Thunderslot? Paul Gauge make tyres to fit the air hub rims too. Thanks for the great video. Racing model trains...now there's a thing!!😄
@Homeracingworld
2 жыл бұрын
Only ones I know of are Thunderslot and Scaleauto.
@jimrose2607
2 жыл бұрын
Were the NSR tires in the testing glued to the wheel before truing and/or using the insert?
@Homeracingworld
2 жыл бұрын
No. I’m exchanging tires. Not completely finished testing.
@stevecausey545
2 жыл бұрын
Are wood tracks that fussy? Is it not possible to just sand the tires even? Not trying to be a smart ass, I just don't know the answer.
@Homeracingworld
2 жыл бұрын
They can be very fussy. Plus removing the magnet so there is no artificial pressure smashing the tires in the track. Its all the just the weight of the car.
@stevecausey545
2 жыл бұрын
@@Homeracingworld I just thought an even surface would be enough
@Homeracingworld
2 жыл бұрын
@@stevecausey545 An even surface is a nice thing, until you have uneven running gear trying to race on it. So, ya gotta tune.
@DrDiff952
2 жыл бұрын
In my rc days foam inserts ruined the hobby for me. Various firmness rubber and inserts. Costs went up exponentially. And my interest in the hobby plummeted.
@Homeracingworld
2 жыл бұрын
I remember those days. However, this is a different application. This is just to support the tire center. Personally, just slip on quick slicks and done.
Пікірлер: 23