I'm not sure what your saying, but you did a great job. Well done
@JoseRodriguez-lb1nb
3 жыл бұрын
The bumper looks really good my friend, I am an off-roader and I think that the hooks look really good but they are not going to work out, if you ever pull something with it, I don’t think that they are going to be strong enough, just being attach to the plate
@edyf3520
6 жыл бұрын
Te Felicito, quedo muy bien, al principio tenia mis dudas, pero se ve bien , solo para la proxima pondel un tape grueso a los buches, para que no se raye ni se derrita cuando lo punteas, otra cosa te recomiendo que cambies de maquina de soldar, usa mig, para ese trabajo es super facil, despues que la uses ya no vas a querer volver a electrodo, te recomiendo para empezar una millermatic 140 autoset, tremenda maquina a buen precio, puedes usarla con gas o sin gas, depende del alambre que uses. sube mas videos. gracias.
@quientinharvey2321
5 жыл бұрын
This just gave me alot of ideas for my 02 silverado and 13 tahoe. Great job and thanks for the ideas.
@emmygrey9900
4 жыл бұрын
Totally amazing I love it!
@larrymacdonald4241
5 жыл бұрын
Stick welding, ok, for sheet metal, I've seen some really nice work by other guys, but there are two things I'd like to suggest, number one would be water and welding does not mix, I know a guy who lost his leg because of water and the bad weld it creates. Water main end cap, pressure test, cap blew off, hit manhole came back and took his leg off, along with a few other body parts. Clean, clean, clean, the 3 C's of welding, you will get much better result's if you had a wire brush on a grinder and a hand brush to clean tack welds before putting another one on top of it or beside it. Sand paper etc... and of course a proper chipping hammer, you know, those pointy hammers with a spring handle ??? Cost about $10 here in Canada... Not a bad job for where and how you did it, without too many shop tools, for a backyard job it's not too bad, but I think you will find alot of your welds are going to fail. A mig welder would not make up for a lack of skill and or welding knowledge in general, as some seem to think, I know some guys who put mig welders to shame with a stick welder, old school pipe line welders.
@nomadbound9610
2 жыл бұрын
Acetone
@richardjimenez8397
4 жыл бұрын
Excelente trabajo amigo de verdad que maravilloso trabajo, eres la inspiración de algunas personas saludos desde Venezuela
@samuelclark4525
4 жыл бұрын
That's a lot of work getting those pieces cut right and welded up like that. I admire your work. Maybe someday I will attempt a bigger project like this with my everlast welder.
@cutweldngrind
3 жыл бұрын
I built my Dually flat bed on my channel and that was a task. I am thinking of building one now. Lots of people told me to buy a mig but the arc welder did good.
@Firefly-trike
2 жыл бұрын
@@cutweldngrind how thick of steel plate did you use?
@cutweldngrind
2 жыл бұрын
@@Firefly-trike I did the entire flat bed and headache rack in 10 gauge or 1/8" sheet metal. The frame is C Channel which is 3 and 4 inch by about 3/16 of a wall thickness. I just uploaded a video on the raptor update and you can see the skirts, fenders and lights I used.
@ninoandolinialbinobautista7375
4 жыл бұрын
Te Quedo perfecto, saludos 🇵🇪
@salvadorgonzalez692
6 жыл бұрын
Wow! That came out really nice!!!
@eltallerherreria4156
5 жыл бұрын
If you weld the joints from behind with thick seam, it will work well, if it is a thick sheet metal gauge,muy bueno amigo!
@danny16ist
6 жыл бұрын
Se siente bien en lo personal cuando uno mismo se pone retos quedo con madre tu proyecto solo falta una pintura con textura y se vera de fabrica
@perroloco3297
5 жыл бұрын
Quedo de wevos.. se ve imponente y muy bien hecha.. saludos ese
@oscarbrindis8663
6 жыл бұрын
Muy bonito trabajó Felicidades 👍
@AGuysGarage
2 жыл бұрын
Kick ass work you did there Brother! Much respect, built not bought!!!
@ernestogonzalez121
6 жыл бұрын
Es verdad que los cubanos no solo inventan en Cuba!!!! te felicito hermano, te quedó genial.
@Miproyectoestuyotambien
5 жыл бұрын
GRACIAS
@gonzalogarcia8144
5 жыл бұрын
Excelente Trabajo!!!!
@mariov2866
5 жыл бұрын
Muy buena te quedo ! Felicitaciones !
@MsNick1975
5 жыл бұрын
Good job man !!
@wimm1392
6 жыл бұрын
I understood each and every word, hahahahahaha. Nice job Mr. Thanks for sharing
@electricguysvcs
5 жыл бұрын
Good style - I usually do a major sub-frame of 1/4" tube of 3x3 on underside, then I do the creative stuff on top. Does weigh in hefty but I'm not afraid to go to Walmart parking lot - lol
@ferigle8925
6 жыл бұрын
Muy bonito. Buen trabajo. Aqui en España, eso es casi imposible hacer por las leyes que hay y por lo que cuesta autorizarlo. Felicidades, siga mejorandolo.
@jaimezamora8472
5 жыл бұрын
Me gusto un buen amigo luego te mando fotos del que constuire yo pero lo counstrure de acero inoxidable saludos desde colima mexico
@denalf6370
6 жыл бұрын
buen trabajo, esperamos los proximos videos-
@tdmallet
3 жыл бұрын
What's the gauge (thickness) on the metal used? Also, what did you use to attach it to the truck frame? Awesome work.
@josecstorres
5 жыл бұрын
No ya en serio, muy buen jale, te quedó chida👏👍👏👍
@abozeman100
4 жыл бұрын
I love this video! Now want to do that same thing haha!! Wow
@andrestorres1620
3 жыл бұрын
Mire paso a paso tu proyecto me anime ya que hago soldadura y tengo todo el equipo para crear el bumper de mi tacoma. Realmente quedo brutal. Cuantas hora le dedicaste a este proyecto. Y cual es el espesor de las planchas de metal. Al final cuanto fue el peso del bumper. Cuando si tienes en mente haras el bumper de atras?
@juanluisoso
6 жыл бұрын
Excelente!! felicitaciones, muy buen trabajo Que grosor de chapa utilizaste?
@pe3nja
3 жыл бұрын
Nice work ... love the safety equipment used hehe
@josecervantes1216
6 жыл бұрын
Yo soy soldador y trabajo para una compañia de sheet metal podemos haser todo eso pero ati te quedo bien echo bien diseñado Buena idea
@Miproyectoestuyotambien
6 жыл бұрын
gracias hermano , ya tienes la teoria puedes hacerlas para vender
@sergiomartinezjr.8438
5 жыл бұрын
esos son los comentarios que ocupamos como hermanos. No los comentarios negativos yo no me consider soldador pero si me aviento trabajos como asadores y defensas de estas.
@JoseDominguez-ou5xd
5 жыл бұрын
yo quisiera una para mi nissan xterra
@kevinteriierooiterai6737
5 жыл бұрын
josex5tpyto l cervantes 1
@martinromero5869
5 жыл бұрын
que grosor de lamina podria utilizar?
@LuisRodriguez-mb4vr
8 ай бұрын
SALUDOS DESDE MECICO ,..GRACIAS POR COMPARTIR EXPERIENCIAS EN EL APRENDIZAJE, MUY BUENOS PTOYECTOS, DISCULPA QUE CALIBRE DE PLACA O CALIBRE DE LAMINA ...ES ? GRACIAS DE ANTEMANO POR TU RESPUESTA....
@adriansalvador5562
5 жыл бұрын
Te quedo chida la neta! Ya los acabados es lo de menos se tapa con el bodyfiling.. el diseño es muy bueno..
@father_XL
6 жыл бұрын
excelente video y muy detallado. Saludos!
@armandorodriguez516
6 жыл бұрын
Felicidades buen trabajo saludos
@user-hu2op3hd1e
3 жыл бұрын
Молодец!!! Отлично вышло!
@thecatfelix2988
6 жыл бұрын
Que bien se ve muy buen diseno moderno y no muy pesado. lo unico que me preocuparia es que le pegen un jalon a los( D rings) no vi base de fondo para aguantar un jalon ahi requiere metal de 1/2 o minimo 3/8 atornillado al firme del chassis.
@Miproyectoestuyotambien
6 жыл бұрын
las argollas son de estetica , no se puede alar por ellas, tambien actibarian las bolsas de aire
@thecatfelix2988
6 жыл бұрын
+Mi proyecto es tuyo tambien . Ha todo tiene sentido ahora ! Muy buen diseno disfrute el video grasias por compartir.
@javierwalterpachecoquispe507
5 жыл бұрын
El trabajo excelente muy bonito solo para agilizar el trabajo podrías diseñado en autocat o solidworks así lo mandas a cortar en C N C y te queda perfecto y también usuarias plegadora y abría menos uniones
@nebegama1
6 жыл бұрын
Gran trabajo. Muy bien diseñando.
@hectorsandoval6817
Жыл бұрын
Mil veces que la porquería de defensa que trae original … felicitaciones.. adelante 🍀☘️
@josebarria7205
Жыл бұрын
Excelente trabajo, yo estoy construyendo uno similar para mi suzuki sidekick, lo felicito una hermosura de defensa, saludos desde chile.
@eduardopradellpinedo5532
3 жыл бұрын
Muy burn aporte amigo gracias y saludos te quedo chevere el trabajo
@atlantacraneo9184
5 жыл бұрын
Buen trabajo mi respeto está muy bien hecho ..
@perrosdraza
7 ай бұрын
saludos hermano una pregunta como se llama la herramienta que usas para hacer los cortes
@nationwideofficial7201
6 жыл бұрын
Good work I like your style best of luck.
@a.trevino30
5 жыл бұрын
Qvo!! Se mira chingon.. Haters gonna hate!
@joselacera8716
3 жыл бұрын
Muy buen trabajo me gustó el proyecto te quedó mundial gracias
@CarlosMendoza-ug8jh
6 жыл бұрын
muchas gracias por subir este vídeo y le agradecería que me diga de que espesor es el metal, saludos desde Perú
6 жыл бұрын
Está súper tus trabajos ya me distes unas ideas soy herrero
@mattvandart9055
4 жыл бұрын
that is an awesome bumper dude :)
@gersonvilchezrubiofuentez9184
5 жыл бұрын
Que bonito te quedo amigo...yo kiero uno de esos para mi tacoma 2003..
@soundboydesign1373
2 жыл бұрын
Canada here, excelente jefe! Keep turning that wrench... one love
@evenmvp
3 жыл бұрын
Te quedó CHINGON SE VE MALDITA LA TROCA SALUDOS DESDE HOUSTON Excelente trabajo
@Wdiedericks
6 жыл бұрын
Looks good. 👍
@borjaroque9668
2 жыл бұрын
Eres un artista compadre ojalá tuviera un amigo como tu que me las hiciera para mi yepeta
@user-ho1yx6ks1k
3 жыл бұрын
طراحی اولیه با کارتن عالی بود.ویدیو خوبی درست کردید متشکرم.
@felicianomena3734
14 күн бұрын
EXCELENTE TRABAJO HERMANO!!
@witosarlaw
4 жыл бұрын
Mantap tutorialnya bang...makasi banyak..😊😊
@ELDIESTRODIY
6 жыл бұрын
Brutal hermano saludos desde Puerto rico
@chocador4
6 жыл бұрын
Excelente proyecto, muy buen trabajo y ejecución, saludos desde Chile
@nicolasgarcia449
6 жыл бұрын
En pocas palabras chingon
@breker19er
5 жыл бұрын
Great job!!!
@Aluminio258
5 жыл бұрын
Gran trabajo, muchas gracias por compartirlo.
@Miproyectoestuyotambien
5 жыл бұрын
gracias ti
@darbinsardinassantana197
5 жыл бұрын
Buen trabajo men deveras muy creativo como puedo localisarte quiero uno para mi tundra se ve genial
@bigrik9018
5 жыл бұрын
looks great, good job
@pcabellb911
3 жыл бұрын
Buen trabajo y espero los otros videos, un abrazo desde Perú
@Akhazmat907
4 жыл бұрын
That turned out great
@juancarlosgomezortiz6610
6 жыл бұрын
Se ve bien fuerte la defensa. Muy buen trabajo.
@jazielalmanza4630
4 жыл бұрын
Que extraño me parece que tengas plasma y soldas con electrodo jeje en lo personal también prefiero electrodo que micro alambre,excelente trabajo 👌🏼
@johnfarney5328
6 жыл бұрын
I dont speak spanish but MUY BUENA
@Alexanderbopp
5 жыл бұрын
JOHN FARNEY lol
@jonassal6937
5 жыл бұрын
Si se puede
@Farmor4x4
3 жыл бұрын
que espesor de lamina usastes? 4mm
@Dhdhfbdid
6 жыл бұрын
Para trabajos de soldadura donde puede que requieran resistencia debes de utilizar electrodos básicos o de gran rendimiento, te digo esto porque la mayoría de los que sueldan sin ser soldadores este tipo de cosas lo hacen con los de rutilo que deja un cordón frágil y quebradizo ante vibraciones, dilataciones o esfuerzos. Espero que te sirva de ayuda
@Miproyectoestuyotambien
6 жыл бұрын
gracias , claro que sirbe tu sugerencia
@martinromero5869
5 жыл бұрын
especificamente cual recomiendas?
@Loftur
2 жыл бұрын
@@martinromero5869 alguien que responda, me gustaria hacer el mio
@azaelarcia111
Жыл бұрын
Bueno en mi.pais regularmente usamos electrodos con revestimiento celulosicos para esa clase de trabajos .Saludos desde Panama
@saulcabrera573
6 жыл бұрын
Excelentisimo quedó,todo un pro!
@marvindiaz1293
3 жыл бұрын
que medidas son para hacer uno está muy bueno
@noahgiles777
Жыл бұрын
Que chingon! That bumper is bad ass!
@JuanNuDead
6 жыл бұрын
hola quedo genial, en que espesor lo fabricaste en milimetros
@felicianomena3734
14 күн бұрын
Excelente trabajo hermano!!
@cesarsanchez-rr1hi
4 жыл бұрын
muy bueno! gracias
@rehanniazi3596
4 жыл бұрын
perfect work ,,,,,,
@armindelaroca1735
4 жыл бұрын
Muy buen trabajo 👍🏼
@carlosrdz7468
6 жыл бұрын
Buen trabajo amigo 👍
@manuelenriquemartinezascen2965
5 жыл бұрын
Excelente trabajo amigo! Te quedó super el resultado final!!
@warrenwallace2
6 жыл бұрын
The start of the video you were dead on but that's where it stopped if your looking for a revolutionary bumper make it to encapsulate the bumper and mount to the frame not to replace the bumper. Attaching to the bumper mounts doesn't improve the bumper because as soon as you hit something it will set off the airbags if you mount a encapsulating shell to the tow hooks mount top and bottom it protects the bumper from setting off the airbags but also gives you the protection of the airbags if you hit to hard. Because a hard hit will bend the metal pushing the bumper in setting off the airbags.
@sergiocosta5897
3 жыл бұрын
excelente trabalho. parabéns
@nicolasgarcia449
5 жыл бұрын
Chingon el bumper se mira bien no cualquiera lo ase mis respetos
@Miproyectoestuyotambien
5 жыл бұрын
Gracias muchas gracias
@martinezpablo
6 жыл бұрын
quedó espectacular
@tripudos
4 жыл бұрын
pana esa vergada te quedo chingona,e visto fabricadores hacer cosas mas horibles con mejores herramientas, me quito el sombrero,te la mamaste ,esta chingona
@DORSIAKILL
8 ай бұрын
That’s a good job
@davzarrval2755
6 жыл бұрын
Dr. le quedo chingon
@ronnysegura5875
3 жыл бұрын
Que buen trabajo amigo, que calibre de metal usaste
@sandroortiz9337
3 жыл бұрын
Buen trabajo y disculpa q calibre de lámina usaste gracias
@runesteinsnnkristoffersen5641
6 жыл бұрын
:-) Good work
@Luis-ht9nr
5 жыл бұрын
Te quedo muy bien mi hermano👌. De que grosor es el material ?
@themercy6083
4 жыл бұрын
cua tos metros ocupaste de lamina??? te quedo perrona super bien
@agustinramirez8789
6 жыл бұрын
Excelente video amigo, ese es un gran trabajo, se ve genial ese bumper.
@erodriguezpardo
6 жыл бұрын
Excelente saludos
@chadkennedy529
5 жыл бұрын
If anything, you have to respect the effort.
@phillipcraggs6202
5 жыл бұрын
props for using a stick. I'd go crazy
@juansantiago27
4 жыл бұрын
wow Te quedó perro bien profesional
@samuelrojo8313
6 жыл бұрын
trabajo chingon 👍
@CarlosFernandez-ti3hz
5 жыл бұрын
Te la comistes con la defensa eres un barbaro
@frankfrank4543
4 жыл бұрын
Wow . Este bumper si que quedo como el estilo que me gusta . Te voy a copiar la idea broth!
@Farmor4x4
3 жыл бұрын
llevo 2 añoa esperando q termines el parachoque de la Toyota, q pasol,. nl bi como quedo pintada nk con las luves led hid. donde podria ver el acabado final. Podrias decirme que maquinas se necesitan. una cortadora tipo acetileno?
Пікірлер: 410