Great to see a Defender that still works for a living.
@TheDaf95xf
Ай бұрын
Good morning Baz 😊 I’ve never seen you so dirty in any of your videos I’ve watched lol 😂 I’m only a driveway mechanic servicing my own car 🚙 Your videos are a real pleasure to watch especially with your sense of humour and technical knowledge 👍🏻
@roy2689
Ай бұрын
Hi Baz, I have done many of these in the past we have a fleet of them and done more clutches on these than you can shake a stick at and as a result I've found a few short cuts along the way, instead of disconnecting the hand brake cable by the seat I take the back plate off the back of the transfer box, after you've removed the drum there's four bolts, just whizz them out and tie the back plate up under the chassis, (the hole in the back plate is big enough to to clear the output flange) as for the cat they can be a right pain to get out, if you follow the down pipe to the exhaust there's a straight piece of pipe (about 8 inches or so) that runs along side of the chassis, I get a hack saw and cut it thus leaving the cat in place, on reassembly get a heavy duty 60mm joiner and paste and reconnect (I've done this on all our defenders and not one of them has leaked or come off), now i get that customers might be a bit sniffy about cutting up their exhaust but the time it saves plus broken studs etc makes the job so much quicker, we didn't see how you actually got the box out (3 or 4 lads?), in one of the landrover manuals it gives a diagram of how to make an adaptor (with balance point) to fit on a transmission jack and get the whole thing out in one go and safely, (not to be confused with the adaptor for removing the transfer box on it's own), of course it depends on how many you are likely to do as to whether it'd be worthwhile to make...I hope this hasn't come over as a bit know it all but this is my experience and hope it helps, your videos have undoubtedly helped us. Thanks...
@bazmeredith
Ай бұрын
I got it out myself buddy pulled it to one side then asked 2 lads to help me lift it down, and thanks for the tips 🤙
@mikefarrar8071
Ай бұрын
Brought back memories this one as I used to work at a Land Rover agents in the late 80's. I don't know whether you done a old series 3 but you had to take the floor and seat bases out, which every bolt was usually seized and needed drilling out. Then you had to manhandle the box out through the cab, only 2 days work if you were lucky. It wasn't necessary to take the rear prop off in my day just two screws and the hand brake drum slid over the prop. Keep up the good work.
@10beerman
Ай бұрын
Baz, as a Landy nut I always give the owner the oppertunity to have the gearbag split from the transfer box to check and lubricate the spline "bodge" adaptor between the them. 👍
@norb0254
Ай бұрын
The beauty of the old military defender was the floor plates and tunnel unscrewed ,so access was good you could strap the box and slide it back was a workshop crane
@jamesward5721
Ай бұрын
We break these & Discos for parts, as well as repairing them - so the yokes we're working on are generally total sheds. This one doesn't look much better on the cleanliness front. You have my sympathies, Baz.
@markturner9809
Ай бұрын
As an army vehicle mechanic changed dozens of clutches on series 3 LRovers ....very often on exercise in woods with it hissing down or freezing in depth of a German winter ! Amazingly the general design and repair sequence hasn't changed in over 40 years. Great video
@olliesengineworld
Ай бұрын
Best video up to yet love a old defender mainly cos I come from a farming and oldie worldie back ground 🤣
@marksingleton7199
Ай бұрын
Isn't it strange how landrovers always make you smile even when they are bad to drive.
@castrolgtx5064
Ай бұрын
Fantastic video thanks for sharing baz
@Lexusman65
Ай бұрын
Great work as always Baz.I could smell that thing from down here on the south coast haha.
@waynebrinkley6284
Ай бұрын
Nice bit of old school, great job 🤙🤙
@shaunblakemore7150
Ай бұрын
Been waiting for this 👍
@tomcurran65
Ай бұрын
Good job Baz! The old Nissan Patrol had a transmission brake too, brings me back, heavy box too. I never liked the transmission brake because when its on, it will fail if you jack up one wheel, Try changing a wheel on a car with a transmission handbrake, you think it wont roll cause you have the handbrake on.....Same for an automatic thats just left in Park! if you know you know! if you dont you could be in for an accident! On the landrover/ Patrol, brake locks the prop, prop holds the diff, diff holds the wheels, jack one up and the diff releases the wheel with the most resistance.... the one on the ground!!!
@bazmeredith
Ай бұрын
If you don't know what your doing with them could end in a spot of bother
@stephenwalker6823
Ай бұрын
As my Land Rover is a Series 2A and has selectable 4-wheel drive, with no centre diff., simply selecting 4WD and locking the free-wheeling hubs will stop it rolling during a wheel change. It'd need one wheel at each end jacking up to roll.
@tomcurran65
Ай бұрын
@@stephenwalker6823 absolutely, but for the uninitiated no one would know that you must put it in 4wd to jack up a back wheel. The other solution is wheel chocks or a suitable substitute. Very few people know that the parking brake is on the rear wheels only.... except it's only on the front wheels of a Citroen C5 and some Saab's I think 🤔. I suppose the message is be careful when jacking up a vehicle 👍
@Rockonhayne
Ай бұрын
Hello mate, new sub, loving the videos, would love a toolbox tour and to see what tools you have accumulated over the years and what's your favourite and your alternatives to snap on and what not, keel up the good hard work
@user-br8my6oj8q
6 күн бұрын
Always remember, you don’t need hair to be good looking ! 👍🏻🤓👍🏻
@ginobragoli1448
Ай бұрын
I didn't know they had a Ford Transit engine in them, that explains the FORD stamped on the clutch cylinder. LUK "Made in CHINA" as well🤦♂ Like everything else these days!
@johnmoore7825
Ай бұрын
Good job mate
@Theneurodivergentmechanic
Ай бұрын
Love a Land Rover clutch. Nice job to get your teeth into.
@bazmeredith
Ай бұрын
100% mate don't have to worry about breaking little plastic clips or trims either 😂😂
@Theneurodivergentmechanic
Ай бұрын
@@bazmeredith with being on the trucks, it brings a smile to my face when I work on more robust vehicles
@adamhession3478
Ай бұрын
At 6 foot three I hate driving them, seat doesn't go back far enough and the steering box is always so loose😂 have to say though not the worst to work at. Best of a bad bunch where land rover is concerned🙈
@colliehouse3133
Ай бұрын
The missus looks cute in the thumbnail.
@bazmeredith
Ай бұрын
Who's yours?
@colliehouse3133
Ай бұрын
@@bazmeredith- I’ve got a cow. 😂
@georgedaville4662
Ай бұрын
Brings back memories of our site Land Rovers when we were building the motorways. Ours were much newer but still drove shit on the road. Mud-plugging in their element 👍🇬🇧😎
@travel8033
Ай бұрын
BOSS,,,,,,,, thank you,
@colinblythe3710
Ай бұрын
You could plant spuds in the muck in the footwell - Tell him to buy a brush !! LOL
@gregshearer423
Ай бұрын
It’ll be a farmers work horse they don’t care about a bit of dirt
@rickydub6950
Ай бұрын
That defo needs some assistance underneath, power wash, some stone chip and something on top. it would look mint 😁
@mrautoservices7354
Ай бұрын
Love the thumbnail mate 👌
@bazmeredith
Ай бұрын
Cheers buddy, trying something a bit different
@cabottaxi
Ай бұрын
Proper Land Rover.
@mikeberry304
Ай бұрын
My mate does loads of defenders , he was doing an X farm vehicle , dropped some screws behind the seat , in went the fingers to get them out , and out came his hand with a sheep penicillin needle stuck in his hand 😂😂😂😂, he has differnt home made brackets that bolt to the g box , then sit on the transmission jack in the tunnel while replacing the clutch , no lifting , just a bit of wobbling n back in , Mecano i tell him , he dosent do modern shite like we do 😂😂, ive done a 65 plate vivato today radiatir weeing out , yet again , Vivaro , full front off 😂😂😂😂, done paid gone , dont you love parts guys , never got right stuff , mis match clutch kits no thanks 😂😂😂
@bazmeredith
Ай бұрын
I've come close with needles before now in farmers vehicles 😂😂😂😂
@mikeberry304
Ай бұрын
😂😂😂😂😂😂😂😂@@bazmeredith
@davekebell8359
Ай бұрын
I used to find it easier to remove the engine on them to change the clutch
@bazmeredith
Ай бұрын
Ye I've heard a lot do this, me boss came up to me today and said in the war they had 6 lads 3 either side lift the engine out, I looked at him and said, they never had transit engines in them then 😂😂😂
@davekebell8359
Ай бұрын
😂😂😂
@ringstinga
Ай бұрын
It’s not a bald patch it is a solar panel for a love machine !!🤣🤣🤣
@bazmeredith
Ай бұрын
😂😂😂😂
@3018john
Ай бұрын
Shouldn’t the clutch kit include a spigot bearing?
@marksingleton7199
Ай бұрын
Out of interest, how many miles had the clutch done?
@beekeeperkev
Ай бұрын
I can tell you are on a Land Rover, after five minutes you are covered in crxp
@bazmeredith
Ай бұрын
😂😂😂😂😂
@Scott-oi4go
Ай бұрын
Are you not going to give it a valet for the customer baz😂
@bazmeredith
Ай бұрын
Nope 😂
@peterarries7879
Ай бұрын
Nice one baz
@cypeman8037
Ай бұрын
That vehicle looks like it's storing the original foot and mouth disease.
@bazmeredith
Ай бұрын
Working on vehicles like these helps the immune system!!!! And still to this day I've never had COVID
@cypeman8037
Ай бұрын
Covid the least of your problems working on that vehicle. 🤮
@xxl531
Ай бұрын
Your not bald mate your Just Growing past the hair line 😂😂
@bazmeredith
Ай бұрын
Now that's a new one 😂
@plugman1963
Ай бұрын
Used to do loads of 4x4 clutches, Toyotas, land rovers, nissans etc. I've lived in an agricultural area of Spain for the last 16 years and 4x4s are a must for the farmers around here. The underneath of the vehicles were always a nightmare, years of caked on mud and animal shit! Big poking stick to remove it all first 🤢
Пікірлер: 62