was actually hoping to see a more in depth showcase of this chip from you, great content as always
@sthetixofficial
9 ай бұрын
I will try to make an additional video about this chip later.
@writer6006
9 ай бұрын
@@sthetixofficial that would be great, especially showing the flashing and the new reset function not shown on the other v6 chips
@techj2278
9 ай бұрын
Very clean job and so satisfying to watch. Keep up the good work and thanks for inspiring us to improve.
@sthetixofficial
9 ай бұрын
you are welcome
@techj2278
8 ай бұрын
Hi, i followed this tutorial but ended up switch not booting. I removed all wires and mod chip but still it is not booting up. Do you have idea how to fix?
@krisiluttinen
5 ай бұрын
@@sthetixofficial Fantastic work!! Can you tell me what RPM speed did you set the MA-ANT pen grinder to? Has 3 speeds. 5k, 10k, 15k RPM
@sthetixofficial
5 ай бұрын
the slowest.
@AdrianAndreiRobert
4 ай бұрын
Just did your kamikaze method for the first time. Things are looking good so far. I used as an reper to find the pot, the little dots that are on the PCB instead of really measuring it.
@publicshared1780
8 ай бұрын
You make the kamikaze method look so easy! At some point I'll need to try it.
@sthetixofficial
8 ай бұрын
Be careful: it is not for everyone.
@redmimic5532
9 ай бұрын
You're a good man and people should tell you that every day
@sthetixofficial
9 ай бұрын
thank you
@foxlance
9 ай бұрын
Definitely not for the faint of heart! Still crossing my fingers for a software base vulnerability!
@whitak3r
9 ай бұрын
I understand your concerns but it just isn't going to happen. I'd suggest buying a premodded switch with picofly. Barely more than a used switch. I hope in years to come I will have to eat mt words, but it just won't happen.
@sthetixofficial
9 ай бұрын
yes you can use Yuzu
@foxlance
9 ай бұрын
@@whitak3r I was thinking that since its almost EOL for the switch since S2 is just around the corner, theres a bigger incentive for the hackers to look for exploits, kinda like what TheFlow did during the EOL for Vita. He kept the exploit to himself and only release it after support for Vita was dropped. To be fair, a modded OLED in the market here costs about 33% more than retail. So, maybe that makes sense...
@writer6006
9 ай бұрын
we can all wish, but really it will never happen, and if im being honest this hardware “vulnerability” to me isnt really a vulnerability, it is literally an external chip forcing the hardware into submission by writing to the emmc and pulsing the soc, now it is still literally a vulnerability, but what I would consider a real vulnerability is the original v1 consoles problem.
@TheAmanor123
9 ай бұрын
@@whitak3rbarely more than used? Oled used runs 350 canadian used. Oled modded is minimum 600 cad. Quite the difference. Sold mine for 600 a few days ago, im the minimum lol
@darielexis
8 ай бұрын
Tried this method today, everything worked fine, thankyou so much for your video!
@sthetixofficial
8 ай бұрын
you are welcome
@GiuseppeFregiato
8 ай бұрын
@@sthetixofficial I did It but when I put on my console and after training process, v6s have led light Blue and doesn't open instinct page but NORMAL page. I have checked all value in diode mode and was ok. What's wrong?
@hefdhi
8 ай бұрын
same thing here, blue light then it goes to OFW instead of CFW.@@GiuseppeFregiato
@NPC-Electronics-Tech
4 ай бұрын
@@GiuseppeFregiato That I think is a problem with the CPU flex cable not being soldered correctly
@CuriousTinkering
9 ай бұрын
Love watching your modding videos!
@sthetixofficial
9 ай бұрын
Glad you like them!
@zifytube
9 ай бұрын
I rarely comment on things, maybe I've never even left a comment on youtube... I've done about 20 "kamikaze" mods so far (and hundreds of mods in total, from the first modchips to this day), but I wanted to share one of my thoughts with you, because I greatly appreciate and respect your work. I've thought about it, and I'm interested in your opinion on that, what do you think about the process being done with a cnc laser instead of a grinding pen. In that way, the risk would be reduced and the process itself would be quicker and look cleaner? I would also like to get in touch with you, because we mostly think alike, but you are always one step ahead of me 😂🤣 Anyway, great video and thank you so much for posting this kind of content. I'm glad we have people like you in the community!
@sthetixofficial
9 ай бұрын
I think you can use a CNC laser machine. I do have a laser fiber machine too, but I haven't figured out the correct parameter. you can contact me anytime via twitter / discord.
@Marconi9331
9 ай бұрын
that is a really interesting idea, if possible I would like to see this way to do a kamikaze
@lylyhoussem3396
9 ай бұрын
The best of the best 👍👍. But scratchin the 3 layer is bit chalanging and hard
@sthetixofficial
9 ай бұрын
Thank you :)
@tayebzizoom5238
9 ай бұрын
Thank you for the effort. Provide us with the products you work with
@sthetixofficial
9 ай бұрын
it is prohibited to put the link here
@TheMeowthTeamV2
9 ай бұрын
thanks for making the 3ds mod tutorial it was really useful and i got my 2ds modded
@andyli3955
9 ай бұрын
Awesome video and tutorial as always!!
@sthetixofficial
9 ай бұрын
Glad you liked it!
@ltdmod
9 ай бұрын
Very minor detail but thanks so much for explaining why you don't solder any GND points because of the flex cable!
@rg240
9 ай бұрын
Can you do a v1 install tutorial ? I've learnt a lot from you throughout the years. Thanks
@sthetixofficial
9 ай бұрын
it is more or less like the v2. but i will try to do it later
@rg240
9 ай бұрын
@@sthetixofficial that will be very much appreciated, thank you so much. Is it the same instinct chip with the emmc cable and the v1 cpu cable or something else ?
@sthetixofficial
9 ай бұрын
yes it is.
@rg240
9 ай бұрын
@@sthetixofficial thank you so much for the info
@igobrgameplay
5 ай бұрын
Wonderfull work!
@ANADMASSI
9 ай бұрын
Thanks
@RodGSilva
9 ай бұрын
Well now I want try this method too, let's go buy another OLED hehe By the way... any new reason to not use the FPCB for the point A, 3.3V etc...? Thanks for all clear guides!
@sthetixofficial
9 ай бұрын
it causes signal interferences. that is why, using individual wires are preferred
@etherealyuu
8 ай бұрын
@@sthetixofficialwhat signal interferences will do? Cannot boot to cfw?
@krisiluttinen
5 ай бұрын
@@etherealyuu Noise in the data lines and unreliable connections. Just use enamelled wires 36ga.
@ВладимирЛеонов-и4ш
5 ай бұрын
Please tell me why the chip stops working when installed in the docking station?
@sthetixofficial
4 ай бұрын
it does not.
@benjipintado5145
4 ай бұрын
There is an alternative cmd point to that of the resistor in the OLED switch?
@sthetixofficial
4 ай бұрын
no there isnt
@jasonfederici
5 ай бұрын
What tools do you use and what is the alternative to the kamikaze method you mentioned? Thanks for the awesome video. You gained a subscriber
@sthetixofficial
5 ай бұрын
you can use the dat0 adapter but it could fail someday. I recommend using the kamikaze method for the oled. and i use the ma ant D1 grinder
@Dylan-bn6uc
9 ай бұрын
great video, thank you
@sthetixofficial
9 ай бұрын
Glad you liked it!
@border056
9 ай бұрын
Great install. I stopped installing Instinct chips because the board quality is garbage. Almost half of the board I received had defects. The shops were ok with replacing them but it required ordering more chips. I started installing Pico chips which have been much better quality and always glitch instantly.
@sthetixofficial
9 ай бұрын
Sorry to hear that
@arasumi3408
9 ай бұрын
@1:46 you forgot to blur logo bro :O
@sthetixofficial
9 ай бұрын
yes maybe I will try to edit it using KZitem editor later.
@evastonian08
7 ай бұрын
Hello! not sure if you're around to answer questions, but all my diode measurements are correct and solder joints look okay, FPC is a little rough but measurements seem okay. I'm getting a solid white light on my V6s (other colors show up and go away quickly). White light stays on for like 10 seconds and goes off. disconnecting the cpu cable also doesn't boot the switch. I'm getting a black screen either way.
@sthetixofficial
7 ай бұрын
it is not always about the diode value. White means something is shorting or not right too. Please check everything that were altered.
@SilentlyPrickable
9 ай бұрын
As always, great and informative videos! One thing I would like to know. What kind of interference causes the flex cables? I wasn't able to find much info about it, just some random posts which looked like the chip causes issues with the Switch (black bars on the screen, fps drops, etc.). On the other hand, I had issues with the chip that was randomly un/able to glitch the booting but after sticking it on the shield and covering it start to work properly.
@sthetixofficial
9 ай бұрын
at some point your console cannot boot to the OFW with the kit
@Nic0oable
8 ай бұрын
is this 100% confirmed ? does it always happen, I heard different people say different things @@sthetixofficial
@user-bw5hk5nb3k
9 ай бұрын
So big love inside !!! ❤️ How much grad must the hot air for tinning the dat0 280 grad ? without fan = 0% from 100% ?
@sthetixofficial
9 ай бұрын
it depends on your hot air settings and solder paste type. mine is leaded and needs at least 180c - 200c (real temp) to melt it.
@krisiluttinen
5 ай бұрын
@@sthetixofficial Hmm I don't think you can melt anything at 200c on the hot temp station. Maybe 350c up and airflow to 30-40%, what do you think? Soldering gun will melt solder at 200c but not sure the air station will be good that low. What exactly do you have it set at for ChipQuick solder paste 63/37.
@sthetixofficial
5 ай бұрын
lead free will melt at 225c, while leaded is lower 180c. you need to find the correct settings of your hot air rework station yourself.
@leomelfrancisco6036
8 ай бұрын
Hey there! I have a question here, can i do this mod chip installation with the latest firmware version of switch? 17.0.1. Will there be a problem with the JB? Or some apps? Really much appreciated for the answer.
@sthetixofficial
8 ай бұрын
it is fine
@connorhickey3933
5 ай бұрын
Hey sthetix, I am modding my oled today with the v6s, but the 3.3v capacitor I'm supposed to wire to says 0v even without the wire, do you know what could be happening?
@hopechannelhopemusic
7 ай бұрын
Failed to init sd card error.. samsung evo 512gb.. with OFW switch detect the card...
@sthetixofficial
6 ай бұрын
try using Sandisk cards.
@KOOLAIDxK1D
6 ай бұрын
electric grinder is a horrible idea. just destroyed my board. Also are they changing the clk point on new boards or something? Mine is shaped completely differently.
@sthetixofficial
6 ай бұрын
practice makes perfect and the point location is fixed.
@horroresymisterios3400
3 ай бұрын
hi boss, I did all the installation well, all the contacts are perfect even when checking the tester in diode mode, but always with the OLEDs, every time the chip works 10 times and 1 time it doesn't, it produces a white LED with the instinc v6 or v6s and then the original system starts. always the problem whether it's samsung memories or worse with skhynixm, 10 times the mod starts and 1 time it doesn't, then subsequently like this, 6 times or 20 times yes and 1 no, it goes randomly, and the connections are perfect, I always try changing chips between instinc 6vs, 6v and rp2040 can help me plz, and i do kamikaze
@sthetixofficial
3 ай бұрын
check ur soldering quality and micro shorts if they existed. check the sp1 sp2 flex too (the mosfet area).
@MichaelGuiyeMonguer
3 ай бұрын
@sthetixofficial A question that I know may seem absurd but I'm sure you know something. Can the kamikaze method be performed on a Mariko v2 or a v1? I know it doesn't make sense to do it but the point is in the same place and there are the same resistors nearby (A)? it's worth knowing since it's more common to find normal boards to learn. Thanks
@sthetixofficial
3 ай бұрын
why do we need to do the kamikaze on other consoles while their solder point is exposed. and each motherboard has different layouts, so it doesnt make any sense at all
@MichaelGuiyeMonguer
3 ай бұрын
@@sthetixofficial Because it's easier to find a bad switch board that isn't OLED to practice with, is it possible to find it in the same place?
@sthetixofficial
3 ай бұрын
you mean for practice? you can buy a dead oled board or try using any switch board and sand to the 3rd layer.
@nikeshgupta8362
9 ай бұрын
I did a few V2 and lite need to do an oled. Does the Dat0 adapter work well ?
@sthetixofficial
9 ай бұрын
It does work well.
@benjipintado5145
4 ай бұрын
from the center of the resistor the dat0 is 1 mm right?boss
@sthetixofficial
4 ай бұрын
yes
@thedoctor1126
8 ай бұрын
So i'm having trouble sourceing a good tip for my grinder for this. I have a few but they are not gentle enough for this procedure. Done it twice now with ok results but I know it can be better where did you get that .2mm from if you don't mind me asking
@sthetixofficial
8 ай бұрын
It came with the Ma-Ant D1 mini grinder.
@ОбыкновенныйПарень
6 ай бұрын
Hi, is the same schematic for rp2040 picofly?
@sthetixofficial
6 ай бұрын
yes, i think so
@KuraV12
8 ай бұрын
Where did you buy your hakko fx-951 soldering station?
@sthetixofficial
8 ай бұрын
from aliexpress about 10 years ago
@KuraV12
8 ай бұрын
@@sthetixofficial do they sell originals there? If so can you provide a link to a legit one?
@sthetixofficial
8 ай бұрын
I think you better buy it from Amazon or from the Taobao. Most Hakko products in aliexpress are fake.
@christopherrobert1948
5 ай бұрын
does this mean if have NINTENDO SWITCH V6S must use kamikaze method to find dat0?
@sthetixofficial
5 ай бұрын
No, it is just an alternative method to install the DAT0 connection.
@LonzoTube
5 ай бұрын
Hi, very good video and explained in the most simple way. Just one question, If I don't have a grinder what tool do you reccomend to expose the B and D points?
@sthetixofficial
5 ай бұрын
you better buy a mini grinder, i dont recommend using other tools.
@sthetixofficial
5 ай бұрын
I only recommend using a mini grinder. But maybe you can try to scratch it using a very sharp tweezer
@LonzoTube
5 ай бұрын
Thank you
@bradleyhall4186
8 ай бұрын
Great video again, many thanks. I have this chip coming in the post if I solder it just like the video how would I reset the chip via USB if it ever needs it. Same question for the update via USB process.
@sthetixofficial
8 ай бұрын
If you connect the D+, D- and the Vbus, you just turn the console off, connect the console to your computer and do the Putty procedure. Please watch my Putty guide.
@bradleyhall4186
8 ай бұрын
@@sthetixofficial will do, thank you.
@DangerousPictures
5 ай бұрын
can you post a link to the grinding pen used?
@sthetixofficial
5 ай бұрын
it is the Ma-Ant D1
@consolemods3271
9 ай бұрын
whats the number wire are you using,, in the video,, and is it a solid core wire ?? or Stranded
@sthetixofficial
9 ай бұрын
stranded wire, ul10064 teflon wire.
@krisiluttinen
5 ай бұрын
Enamel wire can be 36ga.
@davidsii5822
6 ай бұрын
may i know what will happen if over grinded? lost the C point, and reached or over grinded 4th layer ?
@sthetixofficial
6 ай бұрын
then you need to manually join the emmc dat0 point to the cpu by removing both chips and reball it.
@davidsii5822
6 ай бұрын
will it destroy the mainboard? if over grinded@@sthetixofficial
@sthetixofficial
6 ай бұрын
yes it does.
@semihdemir6104
9 ай бұрын
Great work! Will there be a seperate video about this chip?
@sthetixofficial
9 ай бұрын
Yes soon.
@deluwusional
5 ай бұрын
which solder paste did you use?
@sthetixofficial
5 ай бұрын
the stirri v3 or the amtech nc 3
@smokinv8
4 ай бұрын
Is this the mod chip and installation method you use on the consoles you sell on your website?
@sthetixofficial
4 ай бұрын
yes.
@smokinv8
4 ай бұрын
@@sthetixofficial I can’t wait to get my oled I purchased off you, I have a v1 unpatched that I’ve modded also using your hats pack
@GreenNati0n
8 ай бұрын
Love the videos! Do you happen to have a schematic for how to connect oled v3 using a v2 cpu cable? I just need help on the cpu portion
@sthetixofficial
8 ай бұрын
No, sorry
@hove131
3 ай бұрын
Just pressing both volume buttons will boot it into stock firmware? No press of the power button?
@sthetixofficial
3 ай бұрын
power it on, and when you reach the chip logo screen, you need to press both volume buttons.
@sthetixofficial
3 ай бұрын
or, press both volume buttons then press the power button.
@hove131
3 ай бұрын
@@sthetixofficial thank you
@ВладимирЛеонов-и4ш
4 ай бұрын
I discovered that with firmware 2.0 Instinct NX V6S loads OFW after working in the dock. stations. If the firmware is 1.3, OFW loading occurs less frequently. What is the most current and stable firmware now? When loading OWF led blink: 1) red light flashing 5 times, 2) purple - 1 time 3) blue - 3 times. Why?
@ВладимирЛеонов-и4ш
4 ай бұрын
The problem was that the wires were long. They should be made no longer by 2-3 cm, as shown in the video.
@speed_gamesss
5 ай бұрын
What is the brand and model of your grinder?
@sthetixofficial
5 ай бұрын
it is the ma-ant D1
@Nic0oable
7 ай бұрын
So about this interference when using the FPC cables: How does this manifest on a switch? Blue screen? Hekate exception ? It just doesnt boot? I installed about 6 chips with them, all working fine for weeks. The seventh is a special one: Worked at first, then started to blue screen on boot. Removing the flex, letting it sit for few hours without power brought it back without blue screens. Reinstalled the flex, working again, after a few hours same problem, bluescreen on HOS boot, blackscreen after AMS logo and no boot. Removed the flex again, and it came back. Any idea? I probably just fked up the solder or flex is faulty, isnt it? E: Points were all good, chip was working all the time, eMMC is fine too.
@sthetixofficial
7 ай бұрын
most of the issue is it cannot boot to the ofw.
@krisiluttinen
5 ай бұрын
Intermittent unreliability due to thermal expansion cycles. Just use wires. The CPU flex is ok but the rest should be wired directly.
@ItalianRetroGuy
9 ай бұрын
19:11 bro dropped the hard O
@lyubo89
5 ай бұрын
Great job! I'm wondering what temp is your solder paste and solder wire? And, just for reference, what temp/airflow do you set your soldering iron for the CPU caps and hot gun for the Dat0?
@sthetixofficial
5 ай бұрын
i dont use a hot air currently but i use a solder paste. you can do the same thing using a sharp solder tip , like the T12 JL02
@lyubo89
5 ай бұрын
@@sthetixofficial but what is the melting temperature for the solder wire and the solder paste? 183c or 138c?
@sthetixofficial
5 ай бұрын
@lyubo89 183c
@lyubo89
5 ай бұрын
Thanks :)
@user-bw5hk5nb3k
9 ай бұрын
Hello, which speed should I choose from 1-5, would I choose between 1-2? Does it take a long time to drill through layer 2? I would like to try this giant because the dat0 adapters are simply disgusting
@sthetixofficial
9 ай бұрын
1 is enough. it took me about 5 - 10 minutes to get to the C point.
@IcyShroomZ
6 ай бұрын
the V6S doesn't seem to be available from ali anymore. Any news, when it will be available again? Or is a new version planned?
@sthetixofficial
6 ай бұрын
it is on ali.
@LarsLarsson-s5e
8 ай бұрын
Nice video! Only 1 question whats the difference between INSTINCT OLED V6 vs V6s?
@sthetixofficial
8 ай бұрын
V6S is the V6 successor it is more advanced
@329salamander
9 ай бұрын
I would like to see an alternative clk point, I don't like that point, let's see if you can find an alternative without having to raise the cpu or emmc. I know you can do it
@sthetixofficial
9 ай бұрын
you need to remove the CPU cover to install the CPU flex cable. And at the same time you need to scratch that D point - as there is no other alternatives. please check the board scans if you want.
@samyhx896
8 ай бұрын
Can i re-use my picofly chip that was installed on my previous oled to my new oled console right away ? Thanks.
@sthetixofficial
8 ай бұрын
you can.
@ThereIExtendedIt
26 күн бұрын
which speed do you use on the grinding pen? speed option 1, 2 or 3?
@sthetixofficial
26 күн бұрын
always 1
@ThereIExtendedIt
25 күн бұрын
@@sthetixofficial thnx!
@gamblerofrats
2 ай бұрын
Is it worth doing the kamikaze method? How long on average until the dat0 adapter will oxidize if that method is used instead?
@sthetixofficial
2 ай бұрын
it is worth. there is no specific day when the dat0 oxidize, it could be months to years.
@gamblerofrats
2 ай бұрын
I see, can we solder the exposed dat0 point as normal and omit the solder paste?
@sthetixofficial
2 ай бұрын
yes
@gamblerofrats
2 ай бұрын
@@sthetixofficial Thank you, one final question: would a Dremel pen bit with a working diameter of 0.5mm be small enough?
@sthetixofficial
2 ай бұрын
@gamblerofrats 0.5 is too big
@ThereIExtendedIt
18 күн бұрын
what temprature is the hot air at? also is this brand > YIHUA 959D-Digital good for this kind of task?
@sthetixofficial
18 күн бұрын
you need to determine the temperature that could melt lead free solder. I set mine to 414 c on my station
@ThereIExtendedIt
18 күн бұрын
@@sthetixofficial which hot air gun do you recommend when on a budget?
@sthetixofficial
18 күн бұрын
@Meowtional I used aoyue, haven't tried other brands
@ThereIExtendedIt
17 күн бұрын
@@sthetixofficial ah alright i decided to go with Atten ST-862D it has the possibility to lower the fan speed for example 414c on 10% causing it to blow less air which percent would you put it on? 5-10%? cause i don't want to damage the pad lol
@ThereIExtendedIt
17 күн бұрын
@@sthetixofficial also what fan needs to be removed you mentioned it at tining the dat0 pad
@Spaceworld-95
4 ай бұрын
Never touched a soldering iron in my life but i still feel like this is somewhy easy??
@sthetixofficial
4 ай бұрын
it is not easy.
@Spaceworld-95
4 ай бұрын
@@sthetixofficial Must say, that is probably because you are very skilled! Read some comments online, better stay off modding it till a softmod...
@sthetixofficial
4 ай бұрын
you can learn step by step
@performancemodchips
3 ай бұрын
Has anyone had an issue with connecting the D+ D- and VBUS wires , when the charger is plugged in, the system goes into a boot loop attempting to boot hekate ? - remove the charge cord and it boots fine (yes using a genuine charger)
@sthetixofficial
3 ай бұрын
Dont connect the D+ D- and Vbus. It has bugs.
@performancemodchips
3 ай бұрын
@@sthetixofficial Will remove them, thank you :D
@MrCANER06
3 ай бұрын
@@performancemodchips So you haven´t had any issues after you had removed them right ? Cuz I have the exact same problem. But I don´t have any soldering equipment, will it be enough if I simply cut all the wires off from the D+, D- and VBUS points ?
@performancemodchips
3 ай бұрын
@@MrCANER06 No issues removing them, if you dont have an iron, cut as close as you can to the points on the mobo and cut as close as you can to the chip, remove the section of wire - done
@maxm4451
9 ай бұрын
If I don't use the Kamikaze method, is the installation the same as V6? Thank you. Very good work!
@sthetixofficial
9 ай бұрын
yes just substitute the kamikaze with the dat0 adapter
@maxm4451
9 ай бұрын
@@sthetixofficial thanks!!!
@SuperEngel123
9 ай бұрын
El punto B que se usa en esta video, es el mismo que se una en la parte de abajo de la placa?
@sthetixofficial
9 ай бұрын
it is the same.
@DknMonterrosa23
9 ай бұрын
Como es el proceso de resetear o flasheo del chip via usb? No encuentro informacion sobre esa nueva funciones del chip v6s
@sthetixofficial
9 ай бұрын
I will make another video about this matter soon. BUT in principle, you can use Putty to reset the console. Just plug the console to you computer and do putty. that will reset it
@misssarabunnie
5 ай бұрын
I think I did something wrong. at 16:40 my Switch displays a text saying Nintendo, instead of ▒░▒░▒░▒
@sthetixofficial
5 ай бұрын
mine is blurred - to avoid getting a strike by Nintendo
@thelopenator
8 ай бұрын
isnt there risk of damaging the screen when using hot air?
@sthetixofficial
8 ай бұрын
it does not.
@weiyann83
8 ай бұрын
Possible to make video how to resetting or flashing the V6S chip directly from the console USB port?
@weiyann83
8 ай бұрын
Sometime happen when chip crash always boot into OFW, we need to reset chip using method taking off the battery and plug in back, is this V6S chip will help to solve the problem reset using USB port?
@sthetixofficial
8 ай бұрын
I suggest buying the V6S next month as they will have new firmware inside it.
@weiyann83
8 ай бұрын
i already soldering it V6S but the problem now i have is MTP not working lolx, did you face same problem?@@sthetixofficial
@weiyann83
8 ай бұрын
very sure this problem causing by soldering USB 3 point, if i unsoldering 3 point all work without any problem, i think some step is missing like need to reinstall MTP driver?
@Deedee48-jg9om
4 ай бұрын
not really sure where a good place to ask this is, but out of curiosity i homebrewed by installing an instinct v6 chip myself, my clk point reads around 1070 which from what I understood means the CLK/D point could be grounded the whole console actually works with all the homebrew though. I couldn't see any issues with it so just tried to turn it on. I'm pretty experienced at soldering, but not really the actual technicalities of stuff, any idea what would cause this?
@sthetixofficial
4 ай бұрын
if it is working then you dont need to be worry of it. try to reverse the polarity of the multimeter, RED probe to GND and the BLACK probe to the D point. You should read about 0.400 - 0.500V
@Deedee48-jg9om
4 ай бұрын
@@sthetixofficial Cheers mate for the reply, might get a reshell in the future and i'll fiddle around then. Whilst it's working I'll just leave it xD
@p3ykhacks
9 ай бұрын
can you still do this without a microscope with those tiny resistors?
@sthetixofficial
9 ай бұрын
nah..cannot.
@SuperEngel123
9 ай бұрын
Puedo usar el mismo metodo de instalación V6 sin problema en este v6s?
@sthetixofficial
9 ай бұрын
you can.
@Skipperc3po
9 ай бұрын
Solder paste 183 enough ?? and thanks for this nice video
@sthetixofficial
9 ай бұрын
ya, any leaded solder paste is enough.
@Skipperc3po
9 ай бұрын
@@sthetixofficial thank you very much
@GiuseppeFregiato
8 ай бұрын
Hello @sthetixofficial I did It but when I put on my console and after training process, v6s have led light Blue and doesn't open instinct page but NORMAL page. I have checked all value in diode mode and was ok. What's wrong?
@sthetixofficial
8 ай бұрын
What chip did you use?
@GiuseppeFregiato
8 ай бұрын
@@sthetixofficial V6S, the same of video, I turni on my console I see multicolor led but After colori change in Blue and console go in NORMAL mode.
@sthetixofficial
8 ай бұрын
Try using other chip or check the signal / solder pads connectivity
@hefdhi
8 ай бұрын
I have the same issue, all values read good, but still it goes to OFW@@sthetixofficial
@GiuseppeFregiato
8 ай бұрын
@@sthetixofficial now it works. thanks a lot
@ThePrinzKassad
9 ай бұрын
Would you suggest to update the modchip? I have a clone hwfly v4 chip
@sthetixofficial
9 ай бұрын
why should you do it?
@ThePrinzKassad
9 ай бұрын
@@sthetixofficial I dunno, maybe there are some features with the newer chips or they are more stable like the RGH3 for the Xbox 360 if you have RGH2 🤷♀
@ThereIExtendedIt
22 күн бұрын
Would 30 awg wire work for the kamikaze point or is that too bulky? I used the 30 awg for xboxes i feel like i may need 36 but someone people said it needed 30
@sthetixofficial
22 күн бұрын
30 is way too big. use 40
@mygmail29
9 ай бұрын
Why use Kamikaze method instead data0 adaptor if it more time consuming, risk, and off course damage the board??
@sthetixofficial
9 ай бұрын
we have alternatives. you are free to choose your preferred method
@mygmail29
9 ай бұрын
@@sthetixofficial i see.
@Bryan-C
6 ай бұрын
@@sthetixofficial I am also curious what benefits the kamikaze method has over the data0 adapter. Why do you chose to use that method? Thank you for all of your content, it is very helpful.
@sthetixofficial
6 ай бұрын
@Bryan-C kamikaze is much more reliable than the dat0 adapter as it is permanently soldered without blowing the emmc with heat.
@Bryan-C
6 ай бұрын
@@sthetixofficial OK, that makes a lot of sense, thank you for taking the time to answer.
@RRihannaVEVO
7 ай бұрын
Does your latest hatspack work with instinct v6s I keep getting error 2002-3540 on OFW doesn’t do it on CFW does it at random times?
@sthetixofficial
7 ай бұрын
it does. try to replace your sd card with other brands
@RRihannaVEVO
7 ай бұрын
@@sthetixofficial it’s not the sd card because I took that out and booted into stock by pressing volume + and - at the same time and I’m still getting that error code at random times on OFW sometimes on the Home Screen sometimes in a game could it be a faulty chip?
@Techh0bbyist_Shop
7 ай бұрын
I have the same problem too. After I change the chip with a new one, no errors. Firmware version 1.3 on both. So could be a faulty chip 🤷
@RRihannaVEVO
7 ай бұрын
@@Techh0bbyist_Shop there’s a few faulty v6s going around apparently but someone mentioned a new firmware sorted some issues
@sthetixofficial
7 ай бұрын
you can try flashing it it with u.pcloud.link/publink/show?code=XZ8rj50ZYMAS0MyiVOVfEnQF3SAGr5eDPM6y it's the newest firmware for the v6s
@RahenDraEz
9 ай бұрын
om baju nya nggak rilis di market place indonesia?
@sthetixofficial
9 ай бұрын
gak bikin sendiri soalnya.
@MelonLemon007
9 ай бұрын
Kang boleh minta tutorial utk update atmos ke 1.6.2 supaya switch nya bs pakai ofw 17. Nuhun ya
@sthetixofficial
9 ай бұрын
tinggal pake pack hats saya, aja, github.com/sthetix/HATS..atau nonton kzitem.info/news/bejne/laCtmqKvsp-Impgsi=Rvzz3RYKYG2rDE1S
@Notpoop906
9 ай бұрын
seen the kamikaze method on GBA temp and I honestly don't see the point. I mean, yeah I get that it's a hard wired connection but still. If we're talking about doing a "proper job" and not using adapters, I'd just reball the EMMC and install a dat0 line under it with pad strips.
@sthetixofficial
9 ай бұрын
You are free to choose your preferred method. Every method has its own pros and cons.
@f8upd864
4 ай бұрын
I lost it at 19:10
@Nic0oable
7 ай бұрын
Where do I get the firmware for this chip?
@sthetixofficial
7 ай бұрын
u.pc.cd/q5SctalK
@Nic0oable
7 ай бұрын
Ur the goat I am searching for days@@sthetixofficial
@rostomzerrougui
9 ай бұрын
Can we use this methode using picofly modchip?
@sthetixofficial
9 ай бұрын
u can
@rostomzerrougui
9 ай бұрын
@@sthetixofficial this method looks easier for me than dealing with the emmc chip
@user-bw5hk5nb3k
9 ай бұрын
Its looks easy yes but one mistake and you recycle 330€ !
@mohandmohand2047
9 ай бұрын
Bro you can cut only small sheld to clk point not all that cut to much 😮... 😅
@sthetixofficial
9 ай бұрын
yes 👍
@nemesisnine3297
9 ай бұрын
I wish I can pay you to get mine done 😢, id be willing to pay shipping and everything
@sthetixofficial
9 ай бұрын
you can buy it from my store
@nemesisnine3297
9 ай бұрын
@@sthetixofficial I'm stupid to navigate, I'm sorry 😅 can you please send me link?
@sthetixofficial
9 ай бұрын
please dm me on Twitter. thx
@COTTONMAU5
9 ай бұрын
жесть какая-то, честно говоря я понимаю, хакинг и всё прочее... но препарировать НАСТОЛЬКО консоль, что аж дойти в итоге до "сверления" слоёв текстолита к нужному пятаку? у меня бы, честно, рука дрогнула ну и Большая Н конечно поизгалялась, хоть её и раскусили, в итоге 😁
@araigumakiruno
2 ай бұрын
i got my v1 patched switch modchipped wth nx instinct v6s and it was very interesting to watch how exactly the dude did my console, good stuff!
@sthetixofficial
2 ай бұрын
thanks
@sebaszavala
6 ай бұрын
Hi Sthetix you are awesome, would you recommend this method over the Dat0 Adapter? I mean, if you get someone with enough experience to ensure it turns out well, would it be better than the adapter? Love your videos
@sthetixofficial
6 ай бұрын
Yes, it is way better than the dat0 adapter as it is permanently attached.
@sebaszavala
6 ай бұрын
Thks for your answer, so you would call this the definitive version of the installby now?@@sthetixofficial
@sthetixofficial
6 ай бұрын
Yes , i always do it by default. It is the best.
@Pepsiily
7 ай бұрын
NOOB QUESTION: Is installing the Instinct NX V6S just like installing the V6? I would like to install it using the dat0 adapter method but not sure which video to follow! Thanks in advance :)
@sthetixofficial
7 ай бұрын
I've replied to your email.
@hawkfeather6802
9 ай бұрын
Looks like a very risky way to mod this. Nice job!
@ennesimo84
Ай бұрын
Best tutorial ❤
@ThereIExtendedIt
25 күн бұрын
had one more question are the solder points the same on the v6 instinct? cause this one is for the v6s and i have the v6
@sthetixofficial
25 күн бұрын
it is the same
@mariadagracadm
9 ай бұрын
Bom vídeo, bem explicado. Mas esse método não tento não, arriscado até demais.
@thomastaubane7674
5 күн бұрын
i think i f.. up my caps on the cpu anyone know what caps it is and where i can get replacements ?
@sthetixofficial
5 күн бұрын
it is a 1uf cap
@KingFerx3
9 ай бұрын
Much love to you! Keep up!
@bartskuchiki2649
22 күн бұрын
Ok I got to the no sd card screen. But booting to ofw results in a blue screen? Any fix?? Thanks
@sthetixofficial
22 күн бұрын
try doing the Level1 unbrick guide
@douglascalixto9086
9 ай бұрын
Great tutorial!!!! Do you intend to make a video about the new features of reset/firmware updates by usb C?
@sthetixofficial
9 ай бұрын
yes later
@douglascalixto9086
9 ай бұрын
@@sthetixofficial thank you guy!!!! One more question. What's your grind machine?
@sthetixofficial
9 ай бұрын
it is the ma ant D1
@krisiluttinen
5 ай бұрын
@@sthetixofficial Do you use two hands to hold the pen steady? Like keep one hand over the other to prevent grinding bit from slipping around?
@hove131
3 ай бұрын
I have the normal V6 chips. I install one on an oled thats fully updated will i need to update the firmware pn the instinct chip via PC? If so is there a place to find the firmware and instructions on how to do so? Thanks
Пікірлер: 350