As a vehicle tech for 32 years i so enjoyed watching this, This guy knows his onions with Merc diesels! His confidence and skills in getting the job done was awesome to watch 👍
@rmower3428
11 ай бұрын
First time viewing one of your videos, what a brilliant experience. No rubbish distracting background tempo / music. Just quality information. Well done and keep up the excellent work Mr
@dominicwebb8000
Жыл бұрын
Brilliant, nice to see someone sharing their skills with others. That’s the sign of a real engineer.
@jamesward5721
Жыл бұрын
Any welded extraction like this is always easier if you use a flux-core Mig - simple reason being it welds hotter, so the extra heat helps loosen stuff, it isn't at all fussy compared to Tig or Mig about contamination - it will still bite hard to dirty metal, plus you can really hose in material to get fast build-up. I grab the welder, start hosing metal onto the broken-off plugs, don't even attempt to fit a nut or anything at first - just hose on metal so you have a nice big area to get a nut onto, then grab a nice chunky nut - bigger the better - sit the nut onto the big weld-gobbet, weld on the nut & then use a low powered rattle gun. Because flux-core bites so hard & deep, generates so much heat in the process, stuff gives up. :-) With normal mig, it's really difficult because there is almost always contamination - which makes for a weak weld that breaks easily, same goes for tig. I failed loads of times using those, almost always because the tungsten/oil/grease/crud made the welds weak & porous. Try flux-core, report back in amazement. :-)
@fastinradfordable
9 ай бұрын
Flux core also has reversed polarity allowing current to flow up instead of down
@beautgrainger147
8 ай бұрын
I hope I never have to do this job, but it's fair to say flux core is pretty underrated and really useful and cheap within it's specific sweet spot.
@rossbritton4008
7 ай бұрын
I served my Apprenticeship under an English Diesel Mechanic..You said you wanted some Helpful Engineering advice..? .Weld a washer, with a hole large enough to go over the object you are trying to extract, to the object..This gives you a larger surface to weld a nut to, and therefore a bigger purchase area for your weld.. The nut can then be welded inside and out multiplying the weld contact area several times..Let it cool right down..Then warm the head around the area of the extraction..NOT Red Hot, just warm and especially with Alloy it will transfer heat quickly..This will expand the alloy and help relieve the tension..Where you used engine oil, George always used Auto Trans fluid..He called it the best lubricant in the world..
@griffenthedog
2 ай бұрын
no argument. & yup, not engine oil tho maybe no issue with synthetic- heat + solvent dwn th arse end & bit more reverse welly & compression impact but yup guy was a joy. wldnt it be neat to get the other 99% of vids off the inet where plonkers think they have discovered the wheel- & still not got it right
@Sammy2o1
Ай бұрын
Mannn I might need to do this. What’s the success rate for this? I broke an extractor bit inside after snapping the nut
@iftikartaxis
6 ай бұрын
Just watch your brilliant engineering skills Nice to see things went wrong but you over came this Looking forward to watching your other videoes Live long and prosper
@888johnmac
Жыл бұрын
the 2 jobs on any diesel engine with the most potential grief .. glow plug & injector removal ( different engines have different levels of PITA ) .. nicely done Luke
@aviator97msncom
Жыл бұрын
I had one break on me. I simply put some rags around it and drove the car for about 5 mile and out it pooped. Compression did it. Nice video.
@julias-shed
Жыл бұрын
That was a master class on problem solving. Loved it thanks for sharing 😀
@wagaf
Жыл бұрын
Fair play showing how to remove glow plugs. Very informative video with lots of trade tips. I have to admire the ending of the video saying "just do it yourself" Great Yorkshire lad running a business and a helpful KZitem channel. 👍
@julianpritchard2558
11 ай бұрын
Amazingly refreshing that a professional actually wants the Joe soaps of the world to learn and try to do the work, rather than just wanting them to send in jobs.
@XPbIM3
Жыл бұрын
Glow plugs job can be a pain in the head.... literally.
@RCmodelManiac
Жыл бұрын
A bit more pain in the ass if they broke in half and stay in the head. Especially if engine belongs to your customer not to you
@COM70
Жыл бұрын
Ha ha ha I see what you did there 😂 very good 👍
@DavidBurgess-captainindustry
Жыл бұрын
Luke, another great how-to video. I would very much appreciate a video on the relationship between the idle control, the low-end rack-limiting nut and the ELR. With some experimentation I have found that by plugging or unplugging the ELR, turning down the idle control and compensating with the rack nut and vice-versa, I get various effects such as more or less jerking, idle speed that varies wildly with temperature or run time, and an engine that will or won't start without accelerator pedal input. Such experimenting is time consuming and after a few hours of it I'm not sure I'm any smarter about how these three things interact and I'm still not satisfied with the level of jerkiness, consistency of idle, or ease of starting without accerator input. I have been able to get every one of these factors working in a satisfactory manner, but never all three at the same time, and I would very much appreciate a tutorial from your expertise.
@billpimblett4043
Жыл бұрын
Persistent talent. Most would have given up in the first five minutes. Great video on 'how to' with humour and excellent information.
@volvos60bloke
Жыл бұрын
Fabulous video with no disrespect shown to the person who sent the head in. Credit to you.
@MyScotty7
Жыл бұрын
Listen,i have absolutely loved watching this video. Im a diy mechanic and work in heavy engineering so i love this. I have subscribed and please keep these fantastic videos coming.
@geoffcampbell7846
5 ай бұрын
Brilliant video, and some clear experience and learnt skills being brought to bear on a difficult job for the average DIY mechanic. I really enjoyed that. Cheers 👋🇬🇧🇪🇺🇺🇦
@outbackmotorcyclesandengin867
Жыл бұрын
Great video, I totally agree with your comments (learn to do it your self). We have a nation of thickits who expect everything done for them yesterday for nothing. When I was about 10 years old I blunted one of my father's drills and put it back in drill box. When dad got home I was promptly dragged back to his workshop by my ear, then dad showed me how to sharpen the blunt drill. I couldn't go and what I wanted until I could sharpen a drill bit, best thing dad ever taught me. I did a tool making apprenticeship after leaving school at 16, the only thing I've not go my head around over the years is fixing diesel injection pumps and injectors, I send them to the local specialist.
@capedoryus
11 ай бұрын
Best video to date. Have had MB diesels most of my life and now I understand SO much more. Thank you. An entire diesel course in 20 min. Saved in video library.😊. Great promotion for your products.
@glennmiller1005
8 ай бұрын
very enjoyable video. first job I learnt to do as an apprentice . sharpen drill bits. spent over a week sharpening a big box of drill bits all different sizes.🤣🤣
@russellhaller9304
Жыл бұрын
Hey Luke I know you guys are over the pond and use the metric system regularly, but Ive found the holes in the sleeve where the tungsten lives if it breaks down low like it should is right about .250 and you can tap it to 5/16x18 and keep the remaining plug sleeves as strong as possible for the slide hammer and skip a step. Thought it might be helpful if you hadn’t tried it yet. Great video!!
@russellhaller9304
Жыл бұрын
Also you can tap the plug sleeve with a left hand tap and back the glow plug out with a grade 8 left hand 5/16x18 if your lucky, its worked for me a couple times. 👍🤘
@lewiscunliffe1051
4 ай бұрын
Came across this video today as I have patiently taken the whole day to remove mine and onto the last one that’s moved back and fourth with loads of thread breaker and wd40 and pop snapped past the nut. Currently using a self tapping screwed into the tip (tungsten luckily attached to the top that came out) and have tried pulling it out with not much luck. Have started to remove the front of the van just so I can get a slide hammer on it. Thought I’d have a look online for any tips as although I done this when the engine was hot it doesn’t take long for it to cool down and that carbon turn into what I can only describe as bitumen like hell 😂 Glad I stumbled across it as just for what turned out to be an American Steven hawking impression 😂 you get a follow for that alone and a great video insight 👍🏻
@FiglioBastardo
Жыл бұрын
I absolutely appreciate the time and tips you constantly share! I'm wanting to slap one of these beasts into my mk4 jetta tdi after we blow up the 1.9l 😂 We're going to go for a stick shift diesel record when she's all done.
@georgemarshall6657
Жыл бұрын
Not just build a pd130/150 606 in a transverse engined VW seems difficult....
@FiglioBastardo
Жыл бұрын
@@georgemarshall6657 true that is an option but we're going full tube chassis and want to see a record for a stick shift diesel sedan. 🤣
@CalneRotary
6 ай бұрын
Thanks for your insight, I feel a lot more confident now in tackling this job
@AdamBeaumont-s7w
6 ай бұрын
Not sure how or why I came across your video but I loved watching it. I feel 500 is more than fair for what you've done.
@homer1033
6 ай бұрын
totally amazing footage of how to remove broken glow plugs like i have at the moment on my vivaro. brilliant step by step video an well informative great job
@johnrecycler8275
7 ай бұрын
Great video and repair. I like the fact that you are teaching other people to fish. I know you have been doing that for a while but I worry about using a powered device for running a tap, it's risky. I think a lot of technicians would have destroyed that cylinder head and then told the customer they need to buy a new cylinder head. I commend you on a job well done.
@paulbartley4764
6 ай бұрын
Another top tip for you, having been here with bust off plugs and just the shank left deep inside the head, all options exhausted… Heat the head! Stand the head up in front of a space heater, mines the torpedo type, leave it for 10 or 15 minutes then try, I get them so hot you need welding gloves to handle, build this into your process and hopefully you’ll find it helps loads, surface before refitting.
@robertcornelisse8664
2 ай бұрын
Just found your channel. I don't have a om606, but still enjoy your video's
@spideybrent
2 ай бұрын
Hello from Moosomin,Saskatchewan you have great videos and great at communicating. Thanks for sharing
@OfficialHypoxic
8 ай бұрын
Absolutely brilliant work, one thing I will say is get a 1/2 socket. Will make your impact much more effective
@malcolmyoung7866
Жыл бұрын
Easily your best video/tutorial. Well done for putting this it there encouraging owners of diesel engines in general to have a go. Thanks Luke.
@sshep7119
Жыл бұрын
If all hell let loose and things seem like they can't be salvaged, the tungsten and entire glow plug can be removed by using an EDM drill. Some shops have something similar for removing broken taps or siezed bolts. Maybe in the UK the heads are readily available, but here in the States not so much. Never scrap it unless all options are exhausted.
@evosgarage
Жыл бұрын
Another great video to watch full of knowledge material 👌🏼 I used your previous video as a reference when I did my glow pugs, they were all stuck, I went through the process as you explained and everything went smooth, I managed to extract 5 of 6. I only failed to extract the last one because I'm an idiot, It was already dark, I was really exhausted and instead of calling it a day, go get some rest and carry on the next day I tried to just get it done and didn't remembered to replace the stud I was using to pull the glow plugs out, it was probably already really stretched after removing 5 glow plugs and when I went to extract the last one it snapped inside the glow plug. I tried welding a nut to the top to remove it but I didn't let it cool enough as you mention in your video and jus kept snapping. I got the engine back together and kept using the car in the hope the engine would spit out the glow plug since the threads were already drilled. It's been 2 years 😅😭 Maybe when I get one of your mechanical pumps, a big turbo and some propper boost it will finally come out! Keep it going man, all the best, I love your work!🤜🏼🤛🏼
@johncampbell4498
8 ай бұрын
flippin MEGA! this is the best Engineery Nerdy thing i have watched on youtube this last year. Solid Effort, determination, confidence backed up by those TIG skills. keep on this track tackling hard shit jobs with honesty.❤
@robertreavley7145
Жыл бұрын
Luckily the plugs in my 2.7 5 cylinder CLK came straight out! I’d been made aware of the nightmares! And used the small impact. And yes I fully agree with sharpening drill bits! My mentor a blacksmith called Stan pike. Showed me how to sharpen drills! One skill I’m truly grateful for!! ❤ the videos bud! 🎉🎉❤❤
@bertjetolberg103
Жыл бұрын
I had to drill out an injectorbolt of that engine Its worser then a glowplug
@robertreavley7145
Жыл бұрын
@@bertjetolberg103 the Black Death 💀 luckily I’ve not had to do that yet!!
@John-c1n9t
6 ай бұрын
Once upon a time basic engineering skills that we who did real apprenticeships had.Mine was with Holroyds at the gear works in Milnrow some 40 odd years ago first year with Jack Valentine and Dave Kirk in the training school followed by production work. Tig had not been invented then but we did Gas and Stick in addition to bench fitting, machining sheet metal work etc all between the tender age of 16 to 20. We have fallen along way as a Country. Good recovery of this cylinder head well done.
@unaeruditi
11 ай бұрын
My glowplugs have been in for 7 years with 70,000 extra miles. every year I'd say to myself I'd need to change them but never did. Last week I got new nozzels and will clean out the prechambers. All glowplugs came out perfectly because I used gray anti-seize on them back then. Use Anti-seize on the whole plug except the black anode part. torque to 25Nm and you will never have any issues. Use left over transmission fluid fluid as thread penetrating oil if you did not anti-seize.
@ancca78
6 ай бұрын
om606, i have to change number 1 and 6 glow plugs. they are stuck, bad. mayby this vid helped enough. wery good and informative, thanks!
@iandibley8032
28 күн бұрын
Congratulations, very high-quality work. Very few mechanics would have the necessary skills or Tig Welder, many years of tig welding experience needed to perform these welds in such a confined place any mistakes and damage to the aluminium head would occur. Personally, I have tigged stainless & and alloy for close to 40 years ,I would cautious doing this repair. I remove my hat to you.
@Jonodrew1286
10 ай бұрын
As this is something that I do on a daily basis on the vehicle - believe me many people are willing to try but only a select few are knowledgeable even in garages. In garages like ypu say in your workshop it takes time and time doing better things like a service or fit a replacement part. So its a specialist job, hence calling q specialist - I have seen many attempts with broken drill bits, easy-outs - do in my opinion it can be the difference of being lucky, having experience or inadvertently scrapping your cylinder head. Your advice and methodology was sound though 👍👌🙏
@skysurferuk
Жыл бұрын
Most metal will shrink slightly on air cooling, so leaving it to cool, & maybe warming up the casting should help. You're quite right.
@cullenmiller8170
Жыл бұрын
Nice video of fixing that head up. I was surprised you didn’t use a glow plug hole reamer to clean the bores. I have not bought one in a long time, but I didn’t think they were to expensive.
@ClementKaiman
2 ай бұрын
❤ Thanks we love you you for sending me your important. Very kind of you.❤👍🙏🔥
@ALKUKES
10 ай бұрын
Hi there, one if the plugs on a v8 mercedes engine om628 keeps spinning then i left it its been running fine for 3 years now the light has com on, time for new set, but i know i left one unchanged, what tool should i buy what precaution do i take ? Any help much appreciated
@moraleamilne8360
Жыл бұрын
Best way I found to remove them was to just take them all out while the head was still in the engine and if one or two broke just to leave them in the head. Make sure to keep extras and a ratchet in the van and in a couple weeks they just blow out from engine heat and cooling cycles. Pullover and pop the new ones in! Way easier then pulling the head.
@Jonhenrysneip
7 ай бұрын
Very good job, no hurry and you got an top result.
@genarop9375
Жыл бұрын
DieselPumpUK for the win!!
@MeFixingEverything
Жыл бұрын
Thanks for your time and video! A tip from me for people that are about to change air glow plugs , soke them with whatever you like atleast 2 weeks before you start changing them and use torque wrench set to 35nm when undoing them. Video in my chanel
@fascistpedant758
Жыл бұрын
To remove them without breaking them, start by removing the corrosion at the top of the glow plug. Then heat the head of the glow plug to white hot for a minute or two so the heat has time to make it's way down the plug. As soon as it has cooled enough not to burn it, start spraying it with penetrating fluid. Let the plugs fully cool before removing them. Warming up the engine doesn't hurt.
@avit24
Жыл бұрын
Maybe run it upto temp and then go for removing the glow plug.
@victory2115
Жыл бұрын
Heat the aluminium head white hot ?
@fascistpedant758
Жыл бұрын
@@victory2115 The head of the glow plug.
@chrisharrell2449
6 ай бұрын
Time served blacksmith one of the first things I was taught was to heat and cool a nut and bolt , to un seize, the cooling of the nut stretches it over the Still expanded bolt , then when the bolt is also cooled, the not will more than likely be hand tight. Another thing I am surprised to see you not using left-handed drills for cleaning threads
@AliAli-ng5jh
Жыл бұрын
Thanks for all lessons Tks for along compassions and you’re one of beauty mechanical guy in the same time make job funny and simple hope all the best god blessed you mmm finally get welding 💪🏻.
@timmuston5396
11 ай бұрын
Good engineering skills and advice given.
@enormousdork3831
Жыл бұрын
As always, informative and entertaining. Great job !
@sakariaaltonen7428
Жыл бұрын
Nice extraction. Couldn't help but wonder why you didn't shield the glow plug hole wall with a short piece of thin-walled copper pipe? On the one which broke real deep, I reckon you could have just put some copper pipe in the hole and guide and weld a MIG wire down the pipe, soon it would have been sticking out enough for you to attach a nut in it.
@NICOLAI_VET
Жыл бұрын
I am doing PSA diesel injectors. Also doing glow plugs. I'm doing practically the same as you do. Except I use ceramic grease on both injectors and glowplugs.
@MrSpike2450
2 ай бұрын
Amazing work, well done.
@chrisshave7129
Ай бұрын
Thanks for sharing your expertise! One day soon I'm going to have to change the glow plugs and injectors on the 3.0 Iveco in my Peugeot Boxer. I know this stuff is going to come in handy and I'm looking forward to it now ......... not :-)
@flobeeonekinobee9519
Ай бұрын
Couldn't stop watching
@roadiesgarage3816
Жыл бұрын
Upside down keyboard duster cans have worked miracles for me in the field on f16's.
@georgecroney6168
Жыл бұрын
Just found your channel, bloody hell. What a treat this was, subbed and will watch more when i have time 😊
@williamgraham793
Жыл бұрын
Brilliant f..king brilliant 👏money well spent on this man👍
@MrTech1210
5 ай бұрын
Top job!! A pleasure to watch 👌🏻💪🏻
@ewanchalmers70
Жыл бұрын
Well done Luke! As always, another no bullshit vid showin the true side of these jobs! Always a pleasure to watch real life!👍
@UncleRogers01
Жыл бұрын
kzitem.info/news/bejne/lYSpn4xnoWSDn2U
@nickbaker5033
22 күн бұрын
Just a thought stellite (Cobalt drill) for drilling. as it gets red hot the hardness value of the drill exceeds that of the material you are drilling and if flies through it.
@LumpyFPV
6 ай бұрын
Man that accent attempt took me through some uncanny valley feelings. 😳😂
@Desmodromic916
Жыл бұрын
It was a pleasure to watch. Hat down to that allen key at 17:00
@jezrougan
6 ай бұрын
Ahh yes the not so fun job of glow plug removal... I had to change mine a couple of months ago when I was changing the inlet manifold and I snapped two tips off, luckily it was just the tips to drill and tap out, still a painful job... That's when a friend said only do them when the engine is hot.... Great advice for anyone attempting it themselves...
@cristiancaro7865
Ай бұрын
Hi, I seen people welding a nut in place fild up with welding rod, making a stronger atachment , greethings from Norway...;)
@redwood_shores
Жыл бұрын
This was so entertaining and helpful, I just subscribed in a moment. I wonder why there are so few subs on the channel 😮
@66TheGudmundur
6 ай бұрын
You know what you're doing 😊,👍👍
@andreawebberley9245
Ай бұрын
Brilliant video, thanks for the tips
@ranat5526
Жыл бұрын
LR Time recently uploaded a video on this topic, key is to pre soak the plugs and be patient.
@urbanjentry222
8 ай бұрын
Like listening to darkside developments 😂 I enjoy these videos
@khrystree9233
8 ай бұрын
Very entertaining and makes me want to take my 200TDI glo plugs out😊
@91CavGT5
9 ай бұрын
Many years ago an old mechanic showed me that to clean the carbon out of an engine prior to disassembly, you use water. By spraying water into a running engine, the water turns into steam in the combustion chamber and, with enough water and some patience, the steam will clean the carbon out of the engine thus making the cleaning MUCH easier. I don’t know if this process would help, but it can’t hurt.
@BrentWinter-zy8ps
Жыл бұрын
Thread ease by chemsearch is awesome for exhaust manifold bolts and studs an glow plugs give it a go mate I like your stuff I'm a 52 year old fitter and Turner and a marine engineer I know a little bit about this sort of stuff thread ease you'll love it for the hot stuff
@pawelniedzielski2157
Жыл бұрын
Have you ever tried to install new plugs with a thin coat of ceramic grease? I've learned it really helps when I had an OM606.
@MyScotty7
Жыл бұрын
I use this on my om642 engine with 6mm glow plugs!
@marksutherland774
10 ай бұрын
yep, can't wait to change mine ............................ fantastic job done by yourself it might not end so well for myself lol
@southney7211
Жыл бұрын
Great video buddy. The TIG welder is definitely my friend in these situations. You mentioned you used 308L wire. This is normally for welding 304 grade stainless, if I’m not mistaken? 309L is recommended for dissimilar welding. In reality I normally use whatever scraps are laying within reach on the bench 😄 Although for this kind of job, I’d be putting in the effort and seeking out the 309 wire. Persistence is the key though. I’m also glad to see I’m also not the only one who uses the drill to tap threads. Plenty of lube and a quality tap, be fine. It’ll slip in the chuck before it snaps.
@miiigi
Жыл бұрын
Thanx this was one the most usefull video!! I have a M51d25 and I might have to change those plugs so wish me luck😅
@ahill7099
Жыл бұрын
great work , it's funny how your far away from Cleveland OH and some of your slang is exactly the same....
@katiehinds1648
Жыл бұрын
I found the warm engine up first method very usefull . Apart from the rear cylinder . Becouse the oil filter housing hides it and stops you getting the impact wrench in
@splooof
Жыл бұрын
fire
@zigzag7194
5 күн бұрын
I've watched just about 2 minutes of this video and i am not a mechanic but i do all my own repairs. But what i really want to say is and this is just my opinion. You should never use a power tool to remove a glow plug. Yes get it as warm as you can get the engine spray it with penetrating oil i personally use PB blaster.👍
@snazy7777
Жыл бұрын
Thanks for the motivational speech !!
@mrcogginsgarage7062
Жыл бұрын
Nicely Done Luke .
@recorobertos
7 ай бұрын
An excellent job.
@vincemarshall8550
10 ай бұрын
nice one Luke ,good work there ,its a shame theres not a better way ,trouble with unscrewing them is they dont put em in easy access places ,you saved the head there mate ,think the tig welder was key there ,a mig would of been a bit of a blunt tool
@johninstrell3865
Жыл бұрын
Really good video, but I wanted to see how hard the tungsten middle of a glow plug is. So I got one out of my scrap bin which I pulled out of my landrover 300tdi engine a few years ago I sawed it in half with a standard hacksaw blade no problem, so I got a drill bit on and drilled the tungsten aswell which didn't seem that hard
@johnduran5013
9 ай бұрын
Tip slow pressure on wrench. Try to loosen a bit then try to tighten. Slow and steady rock back and forth. Also when warm not cool apply penitrating oil. Leave overnite. Fyi
@johncunningham4820
16 күн бұрын
Excellent work Luke . Just wondering though , since the Head was cold , could a Proper Heat Gun be used to heat it . A Heat Gun can strip Paint so i think it could , given time , produce the Thermal Expansion of the Casting required .
@fishermansbuddy3785
Жыл бұрын
Heat did it finally .. i do heavily recommend let the plugs soak with motor oil for at least a week before get an attempt on it .. a really good lubricant to get em go is the Kent rust penetrate spray.
@bushratbeachbum
Жыл бұрын
Acetone and atf 50/50 is the best penetrative fluid. Just make sure you shake it before you use it as it does separate if stored
@roryfreeman9433
7 ай бұрын
so skilled, great work
@Tomas-cg9ko
Жыл бұрын
If u see its hard to unscrew, requires a lot of force to do it - u feel like u break them - STOP, just STOP. Put some engine oil on each of these glow plugs - treads. Drive for 2 days. Next day before trying to unscrew them - warm up engine to engine working temperature. Then step by step forward backward try to unscrew them. Dont rush. Slowly. Done by myself - everything gone great.
@paulreynolds1510
Жыл бұрын
I know a Master at glow plugs, while engine still in car, and he’s got a Diamond wheel to sort my drillbits out
@richardwhiting299
7 ай бұрын
i really enjoyed this video, thank you
@stephengibbs4372
Жыл бұрын
We always use a smear of copper kote on glows, injecter threads and anything to do with exhaust manifolds/ turbos and they dont jam up again ever
@TheBlaert
Жыл бұрын
I bought a 2003 X5 with the M57 and discovered the previous owner snapped 4 of them... I tried everything to get them out, heat, cold, left hand drill bits, easy-outs and managed to remove only 1. They're not really needed on the M57 so I just left them. If removing glow plugs warm the engine up, find out the shear value and use a torque wrench that will work anti-clockwise. If it won't unscrew then it's time to try something else
@GWAYGWAY1
6 ай бұрын
EDM is the way to go???? Nothing resists it very well.
@Dansdialogue
Жыл бұрын
Ha I learned to sharpen drill bits as it was quicker than going to the stores at a galvanizers venting box section. Thing is that now I want to sharpen small drill bits and my eyesight ain't what it was. 😮.
Пікірлер: 340