Здравствуйте! Скажите пожалуйста как узнать действительно ли неисправность в иммобилайзере. И как её устранить.? Обманку может поставить? Дело в том что есть несколько авто на продажу за копейки которые не заводятся. В объявлениях написано что иммо. Но веры нет в то что написано. Я в Чехии и хочется купить авто за копейки))) Тут часто такие объявления попадаются. Если можете то помогите пожалуйста. Как и чем это диагностировать? (Французы в основном) Если иммобилайзер то как завести автомобиль?
@edvardlau6315
2 жыл бұрын
для каждого концерна своя диагностика или нужно иметь мультимарочник. Для разового пригона покупать нет смысла. ИММО обходят прогаммно/аппаратно, в полевых условиях самостоятельно не сделаете. И опять же проблема по иммо: нужно знать с чем связана - потеряли ключи, отвязался ключ, обрыв антенны или неисправность самого модуля иммо. У КИА РИО, Черато и у некоторых Хюндай 2006...2009 годов была проблема с самим иммо, там пайка сыпалась, пропай всё решал. Но, это все случаи индивидуальны
@user-xd5yy9jq9o
2 жыл бұрын
Скажите пожалуйста, что может быть, приборку у же всю пропаяли, а опком ее не видит и всё
@edvardlau6315
2 жыл бұрын
К-линию на приборку проверяйте
@achimgazelle3641
8 ай бұрын
Hi, unfortunately I don't understand your language. I have the same problem. When I turn on the ignition, the analogue indicators are dead. all the indicator lights work fine. look here.kzitem.info/news/bejne/uI2A0YVjaoaSqYI So is the problem really only the soldering points of the instrument cluster? Should I remove the instrument and re-solder the contacts?
@edvardlau6315
8 ай бұрын
in most cases you need to solder the contacts. It makes sense to remove and inspect the condition of the printed circuit board
@achimgazelle3641
8 ай бұрын
@@edvardlau6315 I have removed the circuit board. Nothing was noticeable. I have nevertheless re-soldered the contacts. Unfortunately was unsuccessful. It did not help. I think that the dashboard is defective. The motor of the coolant temperature indicator vibrates constantly.
@edvardlau6315
8 ай бұрын
@@achimgazelle3641 look again carefully. And it is better to do it under a microscope
@achimgazelle3641
8 ай бұрын
@@edvardlau6315 My friend, I checked with a magnifying glass. No loose solder joints detected. I think it's a chip problem?
@achimgazelle3641
8 ай бұрын
@@edvardlau6315 This morning the instrument worked. After 5-6 attempts, the error came back. I then re-soldered all the soldered joints. The error does not go away. The motor of the cooling water temperature indicator vibrates and hums all the time. I don't know if it's a chip fault or the motor is defective. In any case, I have ordered a new instrument. I hope that the cause is really only the instrument. otherwise the fault lies elsewhere.
Пікірлер: 11