Total life saver. I opened it up for a deep cleaning, didn't document it and ended up confused about the wire run from the rotor into the head joint. Very clear instructions, thanks!!!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@leo94086
6 ай бұрын
Hi, What is the wires for? Is there a battery in it?
@redbrown55
Жыл бұрын
So helpful. I actually used this and then took it a couple steps further to swap out a bad motor. This was invaluable in putting it all back together. There were just too many steps to have it memorized just from taking it apart once.
@OpenMeUpTec
Жыл бұрын
thanks for your support
@1959Aeroflyte
Жыл бұрын
My motor works but there is a little circuit board in the tube behind the motor and that is bad. When I apply power directly to the motor leads, after the circuit board it works but no power is getting through the board. For the life of me I cannot figure out how to get that circuit board out so I can check it out and repair as necessary. Any hints?
@biometrix
3 жыл бұрын
1 Year after i buyed the Dyson v10, the first Time i used this Head it stucks... literally.... Instant. No warranty left... first time used... f*** But with your Video i fixed it, Dyson made an Assembly Failure of their own Product lol... Big Thanks to you! Now everything run's nice and smooth.
@OpenMeUpTec
3 жыл бұрын
thanks for your support.
@docslax
2 жыл бұрын
Very well done! My torque head really need a serious clean and this video was exactly what I needed to dis & re-assemble it. Very clear directions, easy to follow. Thanks for you time OMU it was very much appreciated!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@chriso1541
10 ай бұрын
Very helpful. I went as far as pulling the motor control pcb out as ours had a mysterious fault that the head motor would spin initially then not restart unless left for a while. When I pulled the pcb out it was wet. Careful discussion with the principal user confirmed the head had been cleaned out with a wet sponge. Drying in a warm place cured the fault.
@CMB5226
Жыл бұрын
Thank YOU!!!! Easy to follow disassemble and reassemble!!! My husband didn’t think I was going to be successful lol I disassembled and cleaned it thoroughly one evening. Then, I let it sit out to dry COMPLETELY for 24 hours. I reassembled it the next day. A 1 video! +++
@OpenMeUpTec
Жыл бұрын
thanks for your support
@graziaagnello8619
Жыл бұрын
Complimenti bravissima io ho paura a toccarlo infatti L ho pulito con una pezza ho tolto solo il rullo dopo averla fatta asciugare funziona a intermittenza
@frankfurter7260
2 жыл бұрын
No superfluous babbling before getting right into it. NO MUSIC! No begging for a “like.” Just showing us what the video title suggests. First rate video. Better than 99% of the KZitem videos I’ve ever watched.
@OpenMeUpTec
2 жыл бұрын
thanaks for your support. i never ask for likes, subsribe or anything. just here to show you what you need to know. i do have basic ads though
@frankfurter7260
2 жыл бұрын
@@OpenMeUpTec you may never ask for “likes” but you got one from me. Thanks for the useful content.
@savannac.5778
2 жыл бұрын
Thank you so much! I took my Dyson apart and got very confused trying to put it back together and you saved the day with this thorough walk through!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@_De_Ku_
Жыл бұрын
Thank You Mate.... This truly saved me. I disassembled mine without expecting so many screws. You really did a great Job on this one.. Thank you again..
@OpenMeUpTec
Жыл бұрын
thanks for your support
@imrankhawaja5764
3 ай бұрын
The best video I had ever seen for Dyson head cleaning or opening & closing it back up
@OpenMeUpTec
3 ай бұрын
thanks for your support
@heatheryp8022
3 ай бұрын
i took apart my dyson and panicked when i couldn’t get a couple pieces apart until i saw your video. taking it apart and cleaning it did not resolve my extra loud humming issue but i’m just glad i was able to put it back together 🥹
@BeducationMattress
16 күн бұрын
Very helpful video. I used your instructions to help swap out a defective neck. Thank you!
@OpenMeUpTec
16 күн бұрын
thanks for your support
@GonzoniGiudicessi
Жыл бұрын
Nice job brother. I had mine all apart and forgot how to re-assemble it. Saved my butt!!
@OpenMeUpTec
Жыл бұрын
thanks for your support
@AimanTamimi
9 ай бұрын
You are a life saver! I was in the last part of disassemply and got stuck! Great guide!
@OpenMeUpTec
9 ай бұрын
thanks for yout support
@sevencasper9016
10 ай бұрын
Very helpful thanks! I had trouble keeping the motor in place while putting it back together. I placed the brush tube loosely on and rested it on the outer edge of the chassis while working. It helped a lot.
@danielparagas8504
3 жыл бұрын
Very well done! This is inspiring me to the deep cleaning for mine. Thanks for your service and I look forward to more great content.
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@bent7131
Жыл бұрын
Dang! I was hoping to see you pull out the motor at around 17 minutes! My torque-head only runs intermittently on 1,2 and boost settings. I was thinking the brushed motor might be wearing out...anyway, this video got me 97% of the way there so thanks for taking the time to open 'er up!
@OpenMeUpTec
Жыл бұрын
you can confirm if you have a motor problem by taking out the motor and using it outside. you dont need to disassemble the motor yet. if it spins normally it might be a different issue.
@Neighsayin
3 жыл бұрын
I'm frustrated as I just want an easy way to clean the clear plastic piece of the torque head.
@OpenMeUpTec
3 жыл бұрын
this is the easiest out of all the brands
@Neighsayin
3 жыл бұрын
@@OpenMeUpTec I mean without having to heavily take it apart. I'm puzzled on what to do there. I can take the roller put but the piece the roller connects to is still in the way and I can't throughly wipe it out. And I don't obviously wanna use water
@ericb6481
2 жыл бұрын
Interesting to hear this is the easiest, hopefully the next models will be easier. Great video btw!
@MkDeGraw1
Ай бұрын
Seriously, I gotta void the warranty to clean the head out because it looks like someone threw up in it?!? I don't want to just blast water up in there, it seems like there is an electric motor in there I'd rather not get wet.
@laststory3694
4 жыл бұрын
Looking forward to see new open me up content, maybe every 3,4 month, anything would be fun to disassemble
@OpenMeUpTec
4 жыл бұрын
thanks for you support. i have actually ran out of stuff to open up. probably do more dyson videos since i have the older vacuums and have not made a video for them.
@DrTomtastic
2 жыл бұрын
Well done video. I managed to open, clean and reassemble successfully. Thank you for your work
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@CsabiMolnar85
Жыл бұрын
Awesome tutorial video. It was a piece of cake to clean my V11 motorhead. Many thanks for the perfect help
@OpenMeUpTec
Жыл бұрын
thanks for your support
@TylerPaci2112
2 жыл бұрын
This video is great. My under 2y/o v11 high torque head just stopped working.. it’s clean and spins well by hand but the motor does not spin. I’m going to try to get warranty repair with Dyson first but if they are unhelpful/unwilling I will be coming back here to try and fix myself. Thank you for this
@dcd6115
2 жыл бұрын
Good luck. Dyson has awful customer service.
@TylerPaci2112
2 жыл бұрын
@@dcd6115 Thanks. I was able to get a replacement head shipped as it was on warranty and replaced in about 5 days after I contacted them.
@jessicahibbard8048
6 ай бұрын
The best how to video. Thank you, even for the reassemble!
@OpenMeUpTec
6 ай бұрын
thanks for your support
@danafaulks7808
2 жыл бұрын
Thank you I was trying to figure out how to remove the v-ball wheel.
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@SCLou
2 жыл бұрын
Thanks! The presentation was organized & thorough.
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@vincentvanhelden6186
Жыл бұрын
Thanks for your help. It was a messy job. My mum sucked up dog poo. Had to disassemble the torque head to clean it. yuck yuck yuck.
@Jamiet958
2 жыл бұрын
Thank you. Really needed cleaning and this was easy to follow. Almost as good as new now!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@vapourkl5324
8 ай бұрын
This is the greatest video ever made. keep up the good work mate !
@OpenMeUpTec
8 ай бұрын
thanks for your support
@khalidnasharuddin
2 жыл бұрын
Your videos save my life.Thanks man
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@adriannam6986
3 ай бұрын
Hello! Thanks for the helpful video. When I opened up the clear plastic container the silicone rubber came out and haven't had any luck getting it back in. Any tips on getting the rubber seal back in or is it a lost cause?
@OpenMeUpTec
3 ай бұрын
it is a lost cause
@supermokh101
3 жыл бұрын
Thanks for the sharing. I have accidentally washed them with water recently (without disamble the parta) and the magnetic roller is not working after I use it again (after leaving out for almost 12 hours). Initially it worked for few minutes, but then it stopped. Maybe it is still wet inside? Any tips for me to make it work again?😩
@OpenMeUpTec
3 жыл бұрын
you need to open it up and see the thing with water is that it will rust your connection. it has been the long so that is probably not the issue. the second issue is that water will short curciut the item and could be the reason it is not working. so open it up and see if there is still water left.
@supermokh101
3 жыл бұрын
OPEN ME UP thank you. I will try open it up and check.
@marajonas95
3 жыл бұрын
I am having the same problem.!!
@recyclespinning9839
Жыл бұрын
I was wondering where the motor is. It's the roller itself? Mine broke after very light use. Dyson agreed to ship out this carpet unit. The vaccuem itself works great , so far , and can do the whole house , 1st floor and 2nd floor without no cords. You can touch up a whole house on one charge 👍
@OpenMeUpTec
Жыл бұрын
the motor is the cylinder thing at 17:40
@jerryjenrich7563
3 жыл бұрын
This was a fantastic video. It was just what i was looking for. JJ
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@cooperstores9819
2 жыл бұрын
When I tried taking the brush head out of the attachment it gets stuck about a 1/8 from the start, I was hoping to get some help
@OpenMeUpTec
2 жыл бұрын
it might be stuck and if you have not removed it for a long time it is hard. so pull harder you cant break anything
@AH-wc6jg
2 жыл бұрын
Operation successful. Thanks dude
@OpenMeUpTec
2 жыл бұрын
thanks for you support
@GunRunner3
Жыл бұрын
Excellent video - but I pray I'll never have to use the whole thing, maybe just parts of it if something breaks. Thank you.
@tyrrellnick
Жыл бұрын
Very helpful video thank you! My god though, that constant upward inflection…
@OpenMeUpTec
Жыл бұрын
thanks for your support
@masterofbeastofgames
Жыл бұрын
Strong suction vacuum 🦈 💨
@Bmagj2
3 жыл бұрын
Hello. Unfortately, the water used when cleaning made that black gasket come off around the frame of my motorhead. Could you please let me know ASAP what type of "adhesive" I should buy to remedy this issue? Thanks!
@OpenMeUpTec
3 жыл бұрын
none. just close it up without it and you should be fine. it happen to me as well. otherwise you can use any sealant that can cover the gap. the idea is to not let air through around that area which will cause you to lose suction.
@Bmagj2
3 жыл бұрын
@@OpenMeUpTec Thanks for the quick response! I was almost relegated to use a gasket sealer thats typically used for automotive vacuum purposes.
@user-jg5oe9bd6t
Жыл бұрын
Happened to me too just now lol. I got scared!
@susanz3187
2 ай бұрын
this is very helpful. Thank you ❤
@OpenMeUpTec
2 ай бұрын
thanks for your support
@lakrfan4980
Жыл бұрын
Thanks for this video. It was very helpful.
@cnnw3929
3 жыл бұрын
I have one with a defective head. Dyson is sending me a new one. But, I would like to open the old one up, just to see if I can get it working again. It's doubtful, though. I had the machine running on dry mats, and it just all of a sudden quit. Brush roll turns freely and everything. I'm hoping that it might be saved with a bit of soldering, but I'm not holding my breath.
@OpenMeUpTec
3 жыл бұрын
itis unlikely that it needs soldereing. most likely your motor is dead. you can replace the motor if that the case.
@cnnw3929
3 жыл бұрын
@@OpenMeUpTec It's just a matter of finding a motor. This one is a V11 Outsize. They won't even sell a full head unless they are contacted, and you have a serial number.
@gabrielrubalcaba1180
3 жыл бұрын
Our head came apart. How are they about replacing the parts? You didn't have to send back the broken one?
@OpenMeUpTec
3 жыл бұрын
@@gabrielrubalcaba1180 yes and no. originally you can call dyson tell them what is faulty and they just send you the whole part free. recently when i called up they wanted me to send in the whole vacuum for inpection. whole vacuum is everything that came in the box not just the part. i own 14 vacuum so when they see this they dont ask questions but this time the person couldnt care and wanted me to send it in. i guess it depends who picks up the phone.
@jeffpetrie4667
Жыл бұрын
Great video, great part by part description.
@OpenMeUpTec
Жыл бұрын
thanks for your support
@teknikkazma
5 ай бұрын
Very good video. Helpful
@R2D2trashcan
2 жыл бұрын
Word of warning to those about to start, document carefully where each screw goes. By reassemble time it is quite hard to know what screw went where.
@OpenMeUpTec
2 жыл бұрын
i have a newer and updated version might be more uesful to you
@emceeboogieboots1608
Жыл бұрын
Thanks mate. All we need is for someone at Dyson to accidentally suck up some cat pee a few times and then perhaps they will make one that is more easily cleaned 😔
@anonyrus
2 жыл бұрын
You saved my life, thank you very much!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@chrisparkhill2061
2 жыл бұрын
Thanks for the video, I’ve thoroughly cleaned mine but the brush bar only spins briefly in Eco/Auto mode on my v11, it does work fine in Boost mode though, any ideas?
@OpenMeUpTec
2 жыл бұрын
yes and no. this is a smart head therefore in those mode it will only spin when required. i have not confirm it but i remember thats how it is supposed to work.
@chrisparkhill2061
2 жыл бұрын
@@OpenMeUpTec it doesn’t work at all in Eco/Auto modes on hard floors or carpet. It only works in Boost mode, which I assume bypasses the sensor.
@OpenMeUpTec
2 жыл бұрын
@@chrisparkhill2061 try to give it a clean and see how it goes
@gillianbowden4785
Жыл бұрын
Thank you. This helped us so much
@monicamacias5806
2 жыл бұрын
Excellent video with detailed steps, thank you!. Is there an special kind of screwdriver tip? 😔 Also, I tried to use a coin to get the center out, but it didn't turn out, Do I need to remove the wheel first, as in your video?
@OpenMeUpTec
2 жыл бұрын
can you watch the video and tell me at what time you have the issue. you need a normal phillip head screw driver, trox T8 and T10. you need a screw driver set as that will resolve all your issues
@WeirdAlpha
7 ай бұрын
Outstanding! Thank you!
@OpenMeUpTec
7 ай бұрын
thanks for your support
@ebh9733
Жыл бұрын
Thanks this video help me a lot!
@maxinebarry1618
2 жыл бұрын
Your video is very detailed & helpful but no matter what I do I cannot get the roller out. It comes out about 1cm & thats it. Any suggestions please.
@OpenMeUpTec
2 жыл бұрын
it is stuck. it happens when you have not removed it for a long long time. you need something to help you remove it like a prying tool(a screw driver)
@Jamiet958
2 жыл бұрын
I've just followed this great guide and mine was stuck too. I used a plastic pry tool from my ifixit kit to get some leverage. Needed to be careful not to break the plastic though with the pry tool but it was enough to get it out in the end.
@stephanevilleneuve8080
2 жыл бұрын
So precise and easy to understand :-) 👍🙂
@OpenMeUpTec
2 жыл бұрын
thats nice to hear. normally i would receive a complaint sayingg it is too much effort
@JavaidHameed
Жыл бұрын
you're a life (vacuum) saver. :) thanks
@OpenMeUpTec
Жыл бұрын
thanks for your support
@simonuk1213
11 ай бұрын
Is this the only way to be able to clean the inside of the head? I have the V12 and can’t find any way to remove the spindle inside that the brush cylinder inserts over. Can’t get around it properly to clean the clear plastic.
@OpenMeUpTec
11 ай бұрын
the dyson v12 comes with the same head as this. if not i have other videos on my channel so you can find which head it is. if you are asking about the soft roller also known as the fluffy head with laser i dont have a video for that. currently dyson only has 3 types of torque/motor heads avaliable and i have videos on all 3 of them. if you take a picture of the head i can show you which video it is
@simonuk1213
11 ай бұрын
@@OpenMeUpTec it’s the brush roller head like the one in this video, seems a poor design from dyson if you need to disassemble the entire head just to clean it. I’ll take a look at your other videos though and see if that helps. Edit: my mistake, it’s the V15 detect I have but the head looks the same as this one.
@OpenMeUpTec
11 ай бұрын
@@simonuk1213 i just uploaded a video a few weeks ago for the newer head but it is actually the same thing just now with the words HAIR REMOVAL VANES
@simonuk1213
11 ай бұрын
@@OpenMeUpTec thanks :)
@zhanna2627
2 жыл бұрын
Well done video! My dyson v11 torgue drive head starts to make rottling sound , when I opened it up I discovered the white ring doesn't spin. Can I fix it, any advise , please!
@OpenMeUpTec
2 жыл бұрын
it could be stuck, try to connect it to power without assembling it to see if it work. give it a push to see it spins.
@jkrabacher1
2 жыл бұрын
This happened to me a few days ago. Under the white ring there is a plastic casing which holds a bearing cassette. The bearings on mine were seized up, so I had to get down to the bearing and turn it by hand until it freed up, then I added some lubricant. All is good so far. Hopefully this helps you and saves you $110 on a replacement head (which happens to be out of stock right now). Let me know if it would be helpful for me to post a video of this.
@komoriaimi
2 жыл бұрын
I couldn't get the screws out. Only the f-two first on the sides. Impossible to unscrew the resr=t. Spent like 2 hours and screws won't move.
@OpenMeUpTec
2 жыл бұрын
can you watch the video and tell me at what time in the video you are stuck at
@mr.spl00sh
5 ай бұрын
2:51 Every time I try to rotate the cap it just doesnt move, any tips on how to remove it?
@OpenMeUpTec
5 ай бұрын
it is probably old and has dirty in it. use something big like a coin and it has to come off
@noahmadsen3319
3 жыл бұрын
When I’m putting the rubber seal back on the clear part, it seems like it’s too small. If I try to stretch it it pops out of its track. Anyone had this issue?
@OpenMeUpTec
3 жыл бұрын
i am abit confused at what part you are asking about. can you please watch the video and tell me at what time i can see the rubber thing and where you up to in the video.
@noahmadsen3319
3 жыл бұрын
@@OpenMeUpTec 15:07 in the video. Where are you say not to remove that rubber seal. I missed it the first time and removed it LOL I have the thing back together now, but there’s a section That doesn’t have the seal now. It was like two short when I put it back
@OpenMeUpTec
3 жыл бұрын
@@noahmadsen3319 this is why you dont remove it. it is ok, the point of it is to enusre there is no leak around the head. since it is already done there is nothing you can do to change it.
@AmitBhola
2 жыл бұрын
Could you let me know what screwdriver are needed for opening this. I was able to open Philips screws but rest I think I need other screwdriver
@OpenMeUpTec
2 жыл бұрын
please watch the newer version of the video on my channel it show you everything you need to know kzitem.info/news/bejne/oqRnmKN4iWlpjYY
@okan8096
7 ай бұрын
thank you
@Linni-ns9sm
5 ай бұрын
How do I clean the plastic piece of the torque head on my Dyson v11
@OpenMeUpTec
5 ай бұрын
can you watch the video and tell me at what time i can see the part you asking about
@hv2328
3 жыл бұрын
Great video, Thank you!!!
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@oldvet69
3 жыл бұрын
Thanks for great VIDEO.... What size (s) torx screws are used ?
@OpenMeUpTec
3 жыл бұрын
i think itis t6 or t8 and you need an extra one t10
@oldvet69
3 жыл бұрын
Thank you
@enesgrimes
Жыл бұрын
I accidentally washed the head what should I do now? P.S: not much water exposed.
@OpenMeUpTec
Жыл бұрын
just leave it out to dry. leave it out for a long time like a week
@afizaaziz2887
3 жыл бұрын
My torque head gave me a signal "blocked airway". I checked everything but no blockage. It's working well when I use the other head. Do you think it's the torque head giving problem? Tq
@OpenMeUpTec
3 жыл бұрын
it can be the head has something stuck. open it up and check it out
@afizaaziz2887
3 жыл бұрын
I just opened it up just now. Such a mess in there! So much dust & cluster of dirt! Cleaned that up & now it's good to go! Thank you so much! Saved me from going to Dyson Service Centre here which is quite far from home. May God bless u for your kindness!
@ashkanrmp7442
4 ай бұрын
Mine doesnt come out!! Only thr head gets disconnected and the roller doesnt come out!
@OpenMeUpTec
4 ай бұрын
it is stuck, use a flat head screw driver to pry it out
@TheHoracioestrada
3 жыл бұрын
The roller in mine got stuck and I can’t extract it. I cleaned a bunch of pet hairs and other debris from the rotor connection, but am afraid to disassemble the entire unit.
@OpenMeUpTec
3 жыл бұрын
watch the video a few times before you do it to improve your confidence. since you have this video that covers everything it is ok if you stuff up.
@MichaelBTraveller
2 жыл бұрын
Awesome help, thanks so much
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@mariawilson7899
2 жыл бұрын
I am 64 years old and I think it has to many screws to undo and clean. What other way can I clean the dyson v11. I don't have someone to help me with this. To many areas to unscrew.
@OpenMeUpTec
2 жыл бұрын
you have to watch the videos a few times and et organised. write down where each thing goes
@andrewc83
2 жыл бұрын
Hey what size were those 4 front fin screws, i purchased a used v11 and its missing all 4
@OpenMeUpTec
2 жыл бұрын
dont know size they are
@graziaagnello8619
Жыл бұрын
Ho pulito L aspirapolvere ho tolto solo il rullo il resto L ho pulito con una pezza come meglio ho potuto L ho fatta asciugare adesso funziona solo ad intermittenza cosa è potuto succedere?
@OpenMeUpTec
Жыл бұрын
can you translate that to english so i can help you
@graziaagnello8619
Жыл бұрын
@@OpenMeUpTec serve la traduzione grazie
@elenakii3274
3 жыл бұрын
Thank you very much!
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@drjeffrey1
Жыл бұрын
Why can I not get the slot on the side to turn to unlock the head??
@OpenMeUpTec
Жыл бұрын
you use it for too long and got stuff like dirt in it. you just need to turn harder now
@red__guy
2 жыл бұрын
Thank you
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@AlexWehe
2 жыл бұрын
Hi! What type of screwdriver do you use?
@OpenMeUpTec
2 жыл бұрын
t8 t10 and phillips
@juliesong4196
3 жыл бұрын
What kind of screw is used to take out the wheel in the very beginning?
@OpenMeUpTec
3 жыл бұрын
which one. can you watch the video and tell me what time so i can go back and have a look
@juliesong4196
3 жыл бұрын
0:27 not sure what size phillip screwdriver to use
@OpenMeUpTec
3 жыл бұрын
@@juliesong4196 whatever fits in the hole. i dont know what the size it is as i have a number of screw available and just pick the one that fits
@silviutanase6141
Жыл бұрын
Will this work on a V8 ?
@OpenMeUpTec
Жыл бұрын
yes it will
@twodogzdogue8710
Жыл бұрын
Does anyone know how to clean a dc08 turbo head?
@bethmcgraw7038
2 жыл бұрын
What are the “gates” for? Thx!
@OpenMeUpTec
2 жыл бұрын
to let stuff in. the idea is to close the gate so you have a seal but depending on what you are sucking in you might need space to let the stuff in
@PhillipPresswood
2 жыл бұрын
I have this vacuum and hate it. There's NO reason it should be this difficult just to clean the clear plastic part. Worst design in the history of vacuums.
@OpenMeUpTec
2 жыл бұрын
you should be happy that you can clean it. there is nothing better than this. if you look at the other brand most of them are glued down
@fc1133
3 жыл бұрын
This is the dumbest thing I have ever seen! Not your video, that is. I am talking about the dyson head. Who came up with this garbage!? I have always loved my dyson vacuums, but never knew that you have to take the whole damn thing apart to be able to properly clean the head!? I just wanted to clean the clear plastic part. Shocked to see that the "motor" is not just coming out!!!
@jtbwatson
3 жыл бұрын
I'm here for the same reason. I just got done cleaning and I guess ran over something wet (probably water my dog spilled) and the plastic is absolutely disgusting right now. I figured, hey, it can't be too hard to get this clean. Boy was I wrong... But hey at least we have this video to help.
@fc1133
3 жыл бұрын
@@jtbwatson Sorry to hear that. Here is what I did/will do. 1. I will NEVER vacuum while the floor is wet! 2. I did carefully rinse PARTS of the head under water. As long as you do NOT get the motor wet, you should be fine. 3. I will run my compressor in the morning and will try to "blast" the DRIED dirt off. 4. I will buy distilled water, put that in a spray bottle and blast the entire head with it. I will also completely submerge the head in the DISTILLED water and then blast it with compressed air. Remember, distilled water will NOT harm your electronics. Thanks. Edit: Had a few autocorrect errors, ha ha. There is also no way I will ever take the head apart like that. I refuse. This is ridiculous! No one should have to do that so they can clean their vacuum head...
@OpenMeUpTec
3 жыл бұрын
thanks for your support. at least you can disassmbly this. some brand dont even let you disassemble the head to clean it so after 1 year it is useless.
@ericb6481
2 жыл бұрын
Yeah the same reason why I came here.
@fc1133
2 жыл бұрын
@@ericb6481 I tried a few different things to clean the inside (other side of the see through plastic) and the best thing I cam up with is to just take a moist rag and "sent it" through the head. I do this buy hand, not using any power from the vacuum. Just stick one end of the rag in, and start turning the brush by hand. As it passes through the head, it will tough the plastic wall and clean it... Hope this helps.
@ODoyleRulz
2 жыл бұрын
So many screws, makes me wish the plastic on the head was opaque!
@millmills352
2 жыл бұрын
Toothbrush simple
@melissachisholm7107
3 жыл бұрын
My brush won't come out!?
@OpenMeUpTec
3 жыл бұрын
can you watch the video and tell me what time in the video you are having issues with so i can guide you
@melissachisholm7107
3 жыл бұрын
@@OpenMeUpTec hi, 3:00
@OpenMeUpTec
3 жыл бұрын
@@melissachisholm7107 pull harder
@melissachisholm7107
3 жыл бұрын
@@OpenMeUpTec Yeah of course I tried that. Thanks!
@4tress300zx
Жыл бұрын
If you are going to the trouble of cleaning this Dyson Head and voiding the warranty. You may as well just buy a new one.
@chooken
8 ай бұрын
Stupidest most incompetent comment ever made.
@garyrendano4717
Жыл бұрын
dyson is so over priced its just stupid.. can get the same part after market for like $25 and with LED headlights. that part there from dyson is $160 total rip off
@OpenMeUpTec
Жыл бұрын
i can confirm that the after market one is not the same and is worst than the original. considering the price, the after market one is alot cheaper for the performance hit
@AlvenmodFoto
3 жыл бұрын
Says it all how poorly designed this vacuum is, one shouldn't have to disassemble the head like this just to get it thoroughly cleaned. Rubbish. I feel I wasted my money on this crap. Great video, but it shows just how poorly designed this thing is
@OpenMeUpTec
3 жыл бұрын
you are saying that becuase you have not seen how the other companies do it. this is the best there is. you have not seen there are many you cant disassemble to clean. at least this one you can clear it and put it back together.
@ericb6481
2 жыл бұрын
Hey Dyson system engineers- make sure you add to your user requirements: “must be easy to dis- assemble & clean”. Not like this POS
@AlvenmodFoto
2 жыл бұрын
@@OpenMeUpTec I had an Electrolux I bought over 10 years ago that had better design for cleaning the heads. I think I paid 40 dollars for it, so...there's that. Also, the argument that it's fine because others are worse is not really a good argument considering this thing is twice the price of any other on the market. TBH I am not overly impressed with it overall either, pretty average vacuum cleaner, with a luxury price tag. So not worth it.
@OpenMeUpTec
2 жыл бұрын
@@AlvenmodFoto thats was yeas ago. it is how things are now. example the below vacuum from electrolux. you can not clean it, since it was not made to be disassembled. majority of the stuff is one way only, so once it was made, you cant remove it. so once use it and it get dirty, you need to bin it. it is not just them, all the other companies that make battery power vacuums basically have this issue. the only vacuum that is easier to clean than the dyson is the LG cordzoero but the performance is worst compared to the dyson. www.catch.com.au/product/electrolux-ergorapido-18v-stick-vacuum-cleaner-zb3515st-7824568/?offer_id=39411606&ref=gmc&gclid=Cj0KCQjwnJaKBhDgARIsAHmvz6eN_-RDVYzKnptEFTZgMenZpSXVQ0T3MyoaCXESuvkt-F6Zcq7TGTIaAu-lEALw_wcB
@AlvenmodFoto
2 жыл бұрын
@@OpenMeUpTec you're missing the point. Have a good day.
Пікірлер: 206