This is the best video on the internet for oreck motor repair unfortunately its all in fast forward. I have no ideas where the wires go now.
@VacLab
2 жыл бұрын
Use your browser buttons to slow it down. Try 0.25X for realtime speed.
@KirbyEnthusiast
4 жыл бұрын
Great video , thanks so much giving me the confidence to delve into my Kirby G4 and Legend 2 I’ve just bought for my channel to strip down motors completely and fit new motor bearings . Thanks again
@ReviewingModsOfGames
4 жыл бұрын
Those electrical connectors are rather easy to pull right out of the coil there, also.
@TRec3791
4 жыл бұрын
I bet that improved the airflow of this oldy.
@jackkolpen338
Жыл бұрын
I repacked the bearings and replaced the brushes on an Oreck 2800 H2w. The motor still sparks a bit, even after using a brush seater. Is there anything else as can try to eliminate sparking, short of a new motor?
@VacLab
Жыл бұрын
Nope, you've covered all the bases so to speak.
@dannyn5041
2 жыл бұрын
Motor sounds good my motor is stuck and motor shaft won't turn smells burnt what should I do replace the motor or is the motor likely going bad
@VacLab
2 жыл бұрын
Replace the motor in your case.
@1000BT
3 жыл бұрын
Can you use sandpaper to clean the armature
@VacLab
3 жыл бұрын
Yes, but it's more dangerous. Something like 800 grit to start off with probably.
@KirbyEnthusiast
4 жыл бұрын
Hows the seating stone work, ive never seen one before.
@VacLab
4 жыл бұрын
When the armature spins at high speed, it forces the carbon brushes to seat smoothly with the commutator bars. kzitem.info/news/bejne/0Ip-xX-qiXeQZII
@KirbyEnthusiast
4 жыл бұрын
VacLab thanks for link awesome video . Now I’m a lot wiser. Thanks again for your videos and support .
@JoeLinux2000
3 жыл бұрын
I think you could used some fine sandpaper on the end of a stick. It cleans the commutator. You could use fine sandpaper with your fingers and spin the motor with your hand. Disconnect the power cord of course.
@TopGamingdansk
4 жыл бұрын
what's the name of the lub For the bearings
@VacLab
4 жыл бұрын
It's Mobil EMB as clearly shown in the video. That blue tube thingy. 😄
@TopGamingdansk
4 жыл бұрын
VacLab Can you maybe give me a link I can't find it
@VacLab
4 жыл бұрын
@@TopGamingdansk you can google it and/or perform an eBay search. Use the words Mobil EMB grease.
@garrettdodson6110
4 жыл бұрын
What size/type of bearings are these?? I’d love to replace them in an old oreck I have that’s otherwise pristine!
@VacLab
4 жыл бұрын
Both bearings are the 608 style. I specifically replaced one using a 608Z, which is all metal, no rubber end seals.
@garrettdodson6110
4 жыл бұрын
VacLab awesome thanks bud!
@Sofia-ib8vv
4 жыл бұрын
Nice video. I'm currently having issues reinstalling one of the carbon brushes on my Hoover Futura Canister model S3551 and I was wondering if anyone here has this r something similar and has replaced the brushes themselves and maybe could do a tutorial? Thanks
@VacLab
4 жыл бұрын
I have a TurboPower 5000, which is similar. Unfortunately, I did a full motor refurbishment back in 2016 before I started my KZitem channel. This motor is not easy to work on though.
@JoeLinux2000
3 жыл бұрын
Generally there is a spring that pushes the carbon brush firmly in contact with the commutator. Figuring out the spring orientation on the Oreck is a bit tricky. Don't know about the Hoover Canister.
@georgemartinez1720
2 жыл бұрын
Hreat job
@1000BT
3 жыл бұрын
Where can you get brushes for a 1980 oreck
@VacLab
3 жыл бұрын
Search eBay
@bfrancioso
Жыл бұрын
Could you use Vaseline to repack bearings?
@VacLab
Жыл бұрын
Nope, don't even think about that, wrong chemical makeup.
@georgemartinez1720
2 жыл бұрын
Do you have to wipe down the Commuter To clean it p
@VacLab
2 жыл бұрын
You polish it with a seating stone.
@therandomman6647
4 жыл бұрын
What should I look for for bad signs of this on a Kirby?
@JoeLinux2000
3 жыл бұрын
roller brush should turn freely. Check for broken blades on the suction fan, check the brushes and of course Kirby has a weird twisted belt for the roller. Get a used Oreck if you can. It's the best upright vacuum there is. Kirby's are very heavy.
@jeremywilliams4493
4 жыл бұрын
What is the name of the song played at 14:10
@VacLab
4 жыл бұрын
Nimbus
@golden.lights.twinkle2329
Жыл бұрын
Why replace one bearing and not the other? Where did you obtain the replacement bearing? The music is annoying and completely unnecessary. Had to mute it and then missed your commentary.
Пікірлер: 42