why is my andis blade still a bit higher when the level is fully closed? i tried making all the adjustments possible and i can’t get a perfect zero gap
@Faded_By_Des
Жыл бұрын
Bro I used the ceramic edge medium cutter because the course cutter is to big and it overlaps
@doubledown8229
Жыл бұрын
@@Faded_By_Des Do you have a link by any chance?
@andyrdavis
4 жыл бұрын
If you would hold the clipper in the camera frame it would help. In half the video the clipper is not viewable because it is held off to the side. Also please explain how you are adjusting the alignment between the two blades.
@spalacios9058
4 жыл бұрын
Can you please add a link to this blade?
@CumminsN14DBest
4 жыл бұрын
Say Dawg, Can You Help me with something,.. I Have to original Oster Fast Feed and I Noticed the clipper blades are Sticking/Freezing in my hair and Not Cutting Through (unLike They did when I First Bought Them?! They Cut Was Smooooooth! 1.5 - 2.5 Length, Didn't Matter) My Hair Length is Like a 1.5 Now, Is There a Solution To This Problem? What's The Best Blade combo For ZERO gap and Anti-Rus/Anti Corrosion? I Use Andis COOL Care And The BLADES Still RUST and Corrosion Is Present?! Hmmm,.. I Thinks I HAVE THE WRONG BLADES, Please gimmie the 4-1-1 to fix this problem ASAP! Stay Safe & Healthy Brotha!!
@Mrfhrheit
3 жыл бұрын
For what andis is Tha blade? For the master? Or envy? Or witch model of andis?
@vzeqro-5876
3 жыл бұрын
What if I lose the grey bar
@noneknwsbrah
3 жыл бұрын
Can't push the ceramic all the way down. The tab behind doesn't support the blade to stay in place.
@kingdevine7374
3 жыл бұрын
Did u get it fixed I have the same issue
@kevindorsey5010
2 жыл бұрын
Does the wahl ceramic blade weed work on the fast feeds
@kevindorsey5010
2 жыл бұрын
Work mistype my bag
@mikemartinez1951
3 жыл бұрын
Helpful vid man. Is that ceramic blade #64440
@Chieface11
2 ай бұрын
Any barbers that play clash lmk 👑🏆
@annlawrence6150
4 жыл бұрын
I replaced my blade with these and now it’s pulling on my client’s hair. This blade is too long for my fast feeds so idk what to do lol
@ryanrobichaud5065
4 жыл бұрын
I was told you can't have the 000 Blade for 0 gap but the 1 blade maybe this helps, just about to get this set up...and thanks for video
@Gieszkanne
4 жыл бұрын
This here have 18 teeth there other ones with 25. I think it has to match with the fixed blade. If the moving blade have less teeth they will be wider and overlap teeth of the fixed blade. Maybe that is the cause? But his clipper here also has the 25 fixed and 18 moving. I dont think that this is ideal.
@garrygarcia5008
4 жыл бұрын
They have ceramic blades that are meant for oster feeds on amazon
@quindalleberry6468
4 жыл бұрын
The original blade on my clippers keeps coming up... dont know why. Is this because I have to zero gap it?
@conroyclark2859
4 жыл бұрын
Kmt..... it doesn’t work... ceramic blade too long
@rugfixr
5 жыл бұрын
No link for blade. nice tutorial though
@kingo717
4 жыл бұрын
Scott literally all you do is type the name of the blade in amazon and boom you found it.
@antoniorangel2523
4 жыл бұрын
@@kingo717 what is the name lol, I type in andis ceramic blade and get different sizes
@dragonsKeeper210
4 жыл бұрын
antonio rangel look at the model number buddy. 64440
@antoniorangel2523
4 жыл бұрын
No part #
@jokerboi526
4 жыл бұрын
Cant open it all the way because the bottom of the ceramic blade hits the lever guide =(. Good blade but i rather be able to open lever fully than take out a bald line that i can do with an outliner.
Пікірлер: 29