Now that I know it can be hooked up I can take a look at it. I just did not want to go to a lot of trouble only to find out there was no float in the tank. Thank you.
@TheJBros520
22 күн бұрын
You bet appears to me there is a chip or fuse type wire coming out near the tank. Don't quote me on that as most of my stuff is hooked up. I do have one wire not hooked up. back left side solo yellow wire.
@wayneruckley7346
12 күн бұрын
Thanks for the vid. I found it super helpful. Just a couple of questions pls. Without a cover over the engine where you stand do you get much heat coming through? and, It seems that the CRT23 has the track and bucket control on separate controllers (levers) so when you are moving you can at the same time work the bucket as distinct from most other models. Is that correct? Thanks Wayne
@TheJBros520
11 күн бұрын
Far as the heat from the engine. I never noticed it to be uncomfortable but I also only let the oil temp light get to 70-80 degrees and I just take a break from the machine. Fan running with engine off cools in 10 minutes or so. Far as the controls your pretty much not able to drive and control lift and bucket at the same time. It really doesn't seem to be a necessary option as the work is more slow and methodical. Accurate tight spaces. On off the machine. But i have been good enough now where i will get a little tilt or raise while moving. I'll try get a video out on how I operate the machine asap
@christopherrto
Ай бұрын
Have you had any issues with the bucket being smaller than the tracks? All the other machines I have seen have a bucket as wide or slightly wider than the tracks.
@TheJBros520
Ай бұрын
Thanks, Chris. It's not ideal. Mostly it doesn't effect much general dirt moving. I am purchasing a 48" bucket to speed up grading and we will put out a video on that. We leveled out 18 yards of gravel with the 31" the material is loose so the tracks just pack it down on forward and back dragging. I will say this don't let the bucket size change your mind to one of the lesser Chinese versions . We are 8 hours in. Greased, New oil filter and flushed hydraulics. All precautionary.
@ajdizzle4shizzle
Ай бұрын
Have you performed an oil change yet? If so, what oil filter did you find here in the US that fits?
@TheJBros520
Ай бұрын
Jax will be uploading some helpful videos in the next hour. I will take a photo of the filter. It's a simple Briggs and Stratton filter part number 429932S got it from Menards.
@annacervantes4048
20 күн бұрын
Where would you find the attachments compatible with this machine and do you know if it will work with a trencher attachment?
@michaelbowman3360
19 күн бұрын
Yes, I have a JQ400, Amazon has the attachments.
@TheJBros520
19 күн бұрын
I am buying my Bucket from top dog attachments. I heard the 18th for my bucket.
@davidwarren7220
23 күн бұрын
I just bought a new one of these and the fuel guage does not work. I traced the wire from the guage and it is not plugged in anywhere. Does yours work?
@TheJBros520
23 күн бұрын
It does. I traced mine to being wrapped up with 2 other plastic wraps. I believe out of there it traces down to the bottom right below the red main switch. I could try do a video of what's connected and maybe you could trouble shoot off that.
@ajdizzle4shizzle
Ай бұрын
Nice overview - Curious to know what these run in price?
@TheJBros520
Ай бұрын
We got this one thru Auction Block. $6,000.00 bid price after fees etc. $7,200.00. There was a lot of 10 mini skids in that auction. Prices ranged from $3,800.00 to this price. If you want more info or details on the models that sold for less I could do a separate video on that or if you want info on the other Chinese models pros and cons. Just reply which model and I can give you my opinion on them. Also, projected price point for each one where I think good value is. This is just a guide. Thanks for the comment.
@ajdizzle4shizzle
Ай бұрын
@@TheJBros520 Thanks for the reply! The info you've shared was very helpful. I actually decided to acquire the same model. If you have the time or interest, it would be great to see future videos on your longer term impressions, maintenance overviews and/or recommended modifications. Great video! Again, thanks for the follow up.
@davidwarren7220
23 күн бұрын
I paid $7,500 for mine just a few days ago.
@southerngypsypickersandoff4459
18 күн бұрын
What is the flow rate? Can't find the specs online
@TheJBros520
18 күн бұрын
I'll do some recon later morning and see if I can get any info
@bigsmoke7381
24 күн бұрын
Wouldn’t the new tariffs against China just make the machine cost double what it’s worth now
@TheJBros520
23 күн бұрын
You would think it would, I always have a tough time gauging how long tariffs and such take to hit the consumer.
@bigsmoke7381
23 күн бұрын
@@TheJBros520 well looks like you bought at the right time
@saraygutierrez-jb3fq
7 күн бұрын
Price?
@TheJBros520
7 күн бұрын
We paid $6,000.00 auction bid price. After fees $7,200.00
@robertgarcia-zn7ed
Ай бұрын
Gas tank
@TheJBros520
Ай бұрын
If your referring to the location, it is in the rear bottom left. holds about 6 gallons. It tends to burn 1 gallon an hour as a rough guide. I would highly recommend do not run the machine out of gas.
Пікірлер: 26