Thank you for this info, I had P0014, P0053 & 54 and P0140 all flag up, followed this vid and reset, problem gone 👍
@cybcarr
Жыл бұрын
Did this but it still shows the error. I reckon it needs to be reset. Do I need a device to reset, or it can be done via the car, like service intervals reset? 🙏
@lewish6044
Жыл бұрын
@@cybcarr I also had some of the faults come back, I reckon there were multiple faults, after cleaning this valve in the vid, one fault code disappeared, turned out both pre and post cat lambda had gone as well, so I had to change those as well
@ApolloSupremus
9 ай бұрын
P0014-27 Camshaft B Position Timing-Over-Advanced (Bank1) Thank you so much.Worked, let's see for how long. Indeed there was some metal powder. Peugeot 207 1,6 VTi
@apostoloskratzas9743
Жыл бұрын
This not a sensor....this is a solenoid valve..for Timing avance..via oil control...rotates the Timing...gear via oil pressure..
@egorkin1982
3 жыл бұрын
It’s ACTUALLY SOLENOID! 😹👨🏿🔧
@stephenfoune7137
Жыл бұрын
Looks like the most likely solution to message anti pollution system faulty. Thanks 😅
@1066Kitchen
2 жыл бұрын
Hi can you help answer my question, how many VVTs are there on a Peugeot 207 2006 1400cc thanks
@mark3556
Жыл бұрын
Ok, I hope this will help, i have check engine, very loud sound when this happen while driving, i will answer here if this will solve this problem.
@maroon5maroon556
6 ай бұрын
Hey did is solve the problem
@mark3556
6 ай бұрын
@@maroon5maroon556 Yes it does! Problem is not return to this day, if you have the problem with losing power and loud sound of engine reving you should try this, I bought a new sensor, its cheap and solve the problem in my case.
@mark3556
6 ай бұрын
@@maroon5maroon556 Yes it does! If you have a problem with losing power and loud engine reving you should check this sensor. In my case changing for new sensor totally solve all problems and that error didn't show up until this day. PS. I dunno why my anwser year ago disappeared.
@timetoplaygames2449
4 ай бұрын
@@mark3556with what company of solenoid did you replace the original? what kind of motor do you have?
@mark3556
4 ай бұрын
@@timetoplaygames2449I have Peugeot 207cc 1.6VTI. I don't remember the brand of solenoid, the most important is, that should by changed for new one if you wanna peace for ever :) It's really cheap part and easy to replace.
@Mr11ESSE111
2 жыл бұрын
Is it same thing/solution for HDI version of 207!?
@LewZajdof
10 ай бұрын
Please tell me what voltage must reach the vti cmp sensor in Peugeot 207 1.4, mine is 3.19 v I don't know if it's not enough.
@makhtool
2 жыл бұрын
Can I use WD40 instead of brake cleaner for cleaning.
@watchandfix6724
2 жыл бұрын
No
@berthonnierjacky9317
2 жыл бұрын
thank you sir,easy,i'll try
@hellmystery1
3 жыл бұрын
I have the same problem with my Peugeot 207 1.6 16V Gt. I will try this and i'll respond ith the matter is solved :D. Thanks for the video anyway.
@mancsblue
2 жыл бұрын
How did it go ? Let us know please
@adeeb754
Жыл бұрын
How it's possible i have same problem
@cybcarr
Жыл бұрын
They might be blown away . :D
@aziznaib4104
2 жыл бұрын
احتاج محرك 1.4 vti 207
@miroslavalterov6167
3 жыл бұрын
thank you for great tutorial, I have cleaned sensor and no more engine or polution errror
@jaggass
3 жыл бұрын
Someone on my street has a 207CC with 1.4 VTI engine. The engine runs really bad and when she tries to accelerate it jumps like mad. Could the CMP sensor be bad?
@watchandfix6724
3 жыл бұрын
maybe, maybe something else
@jarocsiszar1981
10 ай бұрын
Kde sa to nachadza na 207 1.4 benzin 54kw
@rufusblagden5077
7 ай бұрын
Can I still drive with this problem ?
@nikolanikica5313
2 жыл бұрын
Hi Watch and fix! what spray did you use in 3:11min... Thanks a lot 🙏
@watchandfix6724
Жыл бұрын
brake cleaner
@s.r6865
3 жыл бұрын
Peugeot 207cc 1.6 88kw this isnt work for me i tried. Any other solution what to do ?
@jupahome4901
2 жыл бұрын
Hello, I have a problem with my car Peugeot 207 1.6 hdi 2011 82kw 112ps, one day I get a text Engine fault repair needed, the car loses power and the engine noise changes sharply, and the engine vibrates, and the gas does not exceed 3, then removed the battery and put it back again this problem is removed, after a month the same problem appears again, I am thankful if you help me solve this problem
@abdullah92sbms
Жыл бұрын
How can i know if it’s not working/not working good? Some times i fell that my 95 hp has no power at low rpm 1800-2500. can you please explain how to know that? Check engine light is not turning on.
@HeloWarLord
Жыл бұрын
if it's not working it would be difficult to open and close with a screwdriver. this device opens and closes oil to the cams which effect how the car is running. its to do with oil pressure (that's how it works on the gti variable cam timing) if it can't open or close because its stuck because of debris in the mesh or beyond. Hope that helps in finding out if you understand what it does.
@BatuhanŞendoğan
9 ай бұрын
I have P1338 Engine Foult. Do you have suggestion?
@Philip---pip267
4 ай бұрын
A sensible suggestion and the only one that's guaranteed to work. Get rid and buy another vehicle. My 207 was a total load of garbage. Depolloution light on average twice a year. Always serviced properly by main dealer. Always drove rough, problems were never conclusive. Brought brand new, scrap at 11 years and 22000 miles. 2 cylinder heads, one clutch, then a snapped belt leading to engine write off. Don't wait for it to happen mate. Get rid now while you can. It's sound advice.
@danielreborn445
3 жыл бұрын
Can you clean it out with just water if I don't have break cleaner?
@watchandfix6724
3 жыл бұрын
No ! no with water if you dont have cleaner you can use petrol
@danielreborn445
3 жыл бұрын
Thanks I actually bought the break cleaner
@danielreborn445
3 жыл бұрын
And I assume you don't have to unplug car battery
@watchandfix6724
3 жыл бұрын
@@danielreborn445 no you dont
@danielreborn445
3 жыл бұрын
I managed to do it, thanks
@jeffellenbroek8082
3 жыл бұрын
This video is this for the p0014 code ? The front solenoid?
@watchandfix6724
3 жыл бұрын
yes front solenoid exhaust camshaft
@nathwin3843
Жыл бұрын
Deos it stop the turbo from spinning? I’ve got a 308
@watchandfix6724
Жыл бұрын
no i dont think so this is somethink else turbo is another, what fault codes you have ?
@nathwin3843
Жыл бұрын
@@watchandfix6724 POO14 I’ve got
@marktodd6613
2 жыл бұрын
I have P0011 on my peugeot 207 1.4 2010 have followed your tip but to no avail also tried replacing the vvt solenoid and camshaft sensors but again no joy I'm stumped as to what's next
@adeeb754
Жыл бұрын
I have same problem
@marktodd6613
Жыл бұрын
@@adeeb754 Might well be that the Timing has slipped you may well need to source a mechanic to sort it out
@RPV76
11 ай бұрын
tighten the hose clamp on the throttle body and clean the MAF sensor, that's what happened to me, it was very noisy and loose power but now it's ok
@marktodd6613
10 ай бұрын
Indeed it was the timing chain had jumped the vvt cog a mechanic friend sorted it and saved me a small fortune in garage costs he was well rewarded for his time
@lukeread3189
3 жыл бұрын
Do you have to drain the oil for this?
@watchandfix6724
3 жыл бұрын
No you dont :)
@scorpionyad
Жыл бұрын
Не в ту сторону викруткою ковиряєш. Клапан йде в бік котушки а не навпаки !
@ivanljubisavljevic907
2 жыл бұрын
i did as you explained but it still shows an antipollution error...
@Jacksparrow-iq6ll
Жыл бұрын
Could also be a head gasket leak, stuff getting into your engine from a leak in the gasket and messing up the engine
@zzhughesd
2 жыл бұрын
10mm ?
@LeedsHypnotherapist
2 жыл бұрын
Yes
@anderlee
3 ай бұрын
Жаль нет описания на русском
@Varenikismetana
3 жыл бұрын
so the solenoid was working and simply doing this removed fault code?
@watchandfix6724
3 жыл бұрын
When you remove the solenoid you should check it does the spring inside move easily back and forward. If the spring is fine you should only clean it and put it back on its place.
@Varenikismetana
3 жыл бұрын
@@watchandfix6724 yea I have p0014 and a cyl 2 misfire, I took the solenoid out, tested it and the wires and put it back in without cleaning it
@watchandfix6724
3 жыл бұрын
@@Varenikismetana if it works well and is not dirty it does not matter that you have not cleaned it
@watchandfix6724
3 жыл бұрын
@@Varenikismetana check the misfire with change the ingiot coils from cylinder 2 to cylinder 3 and delete the trouble code and if again is misfire in cylinder 2 change the spark plugs or if misfire on cylinder 3 change the ignition coil
@watchandfix6724
3 жыл бұрын
i have videos for that too
@korneevelisabeth5059
3 жыл бұрын
Tried this one but it didn‘t work😫 any other ideas on how i can get rid of p0011 and p0014?
@watchandfix6724
3 жыл бұрын
take out the plastic sieve 2:08 ( rarely helps but try ) And you need to check it out if the electrical part of the sensor works
@korneevelisabeth5059
3 жыл бұрын
@@watchandfix6724 we tried it with 12v and it started to move so we guess the electrical part works.
@watchandfix6724
3 жыл бұрын
how often that error occurs or is constant? check the alternator and battery, if the voltage is low these errors may occur
@korneevelisabeth5059
3 жыл бұрын
@@watchandfix6724 well today we noticed my mini has 2 of these valves... maybe the other one is damaged. Can this even be possible ? These error codes are constant, when i try to delete them they‘re occur in like 50-60km again
@watchandfix6724
3 жыл бұрын
in that case it is best to measure the compression. is the engine running well at idle? Have you ever changed a chain?
Пікірлер: 78