Great video at idle manifold vacuum is high so will draw in unmeasured air, open throttle vacuum leak less effect so SHFT falls immediatley. It is great you demonstrating on the scan tool what is happening, need to check my purge valve on my car.
@neildean7515
Жыл бұрын
This is a great video.. now i am going down a rabbit hole to fully understand PCV valve, purge Valve and Suction control valve.. more research to do!
@kennedysgarage3281
Жыл бұрын
That is unfortunately the life of all mechanics at some stage, trying to fully understand the system that they are working on. Well done mate 💪💪💪
@Leroyjenkinsjnr
2 жыл бұрын
Excellent video. Helped me diagnose a lean condition I couldn't understand. I did a smoke test expecting a leak, but none was found. I cleaned a dirty hot wire on the air mass, but the engine light still came back on. After watching your video, I got the customer to call back in the next day, clamped off the evap line and hey presto, problem diagnosed. Thankyou very much for your help!
@kennedysgarage3281
2 жыл бұрын
Excellent Lee, if we all stick together we will fix them faster 🙏🙏👍👍
@evansmarts775
3 жыл бұрын
Nice one Peter major failure on that breather valve ( I have changed 5 within 3 months ) myself , the last one I wanted to order the dealer told me it did not had one 😂 sneaky maindealer, after I pulled the part number he said yes we do this part, but yeah great video
@kennedysgarage3281
3 жыл бұрын
Isn’t it the way they would try to not help the aftermarket 😉
@alexoppongkumi8338
2 жыл бұрын
What's the actual part called ? I wanna buy it for my corsa
@kennedysgarage3281
2 жыл бұрын
Fuel tank vent solenoid 😉
@alexoppongkumi8338
2 жыл бұрын
@@kennedysgarage3281 thank you
@rudo747
Жыл бұрын
Cheers mate ,good advice looks like the issue on my Corsa👍
@kennedysgarage3281
Жыл бұрын
Crimp the pipe with a visegrip & watch the fuel trims react just to prove the concept 🤔👍👍
@lisamurphy4108
2 жыл бұрын
Polo failed emissions in nct .. co was 1.18 . Lambda was 1.08 .. changed bank 1 sensor . full service .. .. got co down and lambda down to pass range ... Then nct 2 weeks later and retest it ..still failed . Co 0.10 pass . Lambda fail 1.38. lambda even higher now .. help
@kennedysgarage3281
2 жыл бұрын
Lambda is the oxygen content, high lambda is high oxygen content. This can be caused even by a small exhaust leak. But get your garage to look at the ‘ long term & short term fuel trims’ this will tell how much fuel the engine ECU has to add or take away & help with the diagnosis. There is also a purge in that model car. Hopefully this will help 🤞🤞
@qpla8838
Жыл бұрын
Tryed replace this solenoid but it was my PCV and had to replace all the vlalve cover for that and fixed this issues
@kennedysgarage3281
Жыл бұрын
Well done 👏👏. The rocker cover/PCV valve is a common failure point too 👍👍🙏
@johncollins8304
Жыл бұрын
Could you say a bit more on the rocker cover problem please?
@qpla8838
Жыл бұрын
@@johncollins8304 The PCV start whistle or hiss when it fail open. I replaced with new OEM cover + gasket kit .
@kennedysgarage3281
Жыл бұрын
@@johncollins8304 the PCV ( positive crankcase ventilation ) is in the Rocker Cover & they fail quite often too. As qpla said replacing the rocker cover solved his issue. Does that make sense??
@johncollins8304
Жыл бұрын
@@kennedysgarage3281 Well it doesn't make sense to me YET but it will soon! Thanks, I'll look into it. But I have no sound coming from rocker cover, no hiss, no whistle. I wonder would that rule it out. Thanks again!
@johnfittis5764
3 жыл бұрын
Just subscribed on recommendation of Dave Sterl. That's a great tip thanks very much for sharing your knowledge👍
@kennedysgarage3281
3 жыл бұрын
Your very welcome & thank you for subscribing 🙏👍
@marion1600
2 жыл бұрын
Purge valve is not venting fuel tank. As the volume of fuel decreases, volume of air needs to increase in the tank. That could only happen by letting atmospheric pressure in the fuel tank not vacuuming it with engine vacuum
@kennedysgarage3281
2 жыл бұрын
The vent solenoid is stuck in the open position, meaning that when the car is not running atmospheric pressure can reach the tank from the intake manifold threw the solenoid. Then on start up the intake pressure drops and draws that air back into the engine giving a lean condition. If the engine is running for an extended period and empties the tank of air the fuel might come back below 10 ( total trim ) but will go lean again if the engine is turned off & restarted. Does that make sense 🤔??? That’s the best I can explain it anyway 😂😂👍
@clueless6559
2 жыл бұрын
LOL even the parts manufacturers label it wrong, its as you say a purge , nice little video again thanks 👍
@kennedysgarage3281
2 жыл бұрын
I’m glad to see I’m retaining your attention 🙏🙏👍
@peterarries7879
2 жыл бұрын
Nice one on reqards of fuel trims, never really been able to get my👍👍 head round it until now, cheers Peter
@kennedysgarage3281
2 жыл бұрын
I’m glad it helped, I have another one recorded about proving an inlet manifold gasket leak recorded which I’ll be uploading in the next week or so. Thanks Peter 👍
@Upthetoon2010
2 жыл бұрын
This may solve the P0171 code I have on my 2008 zafira B which is coming up with the exact same code and info
@kennedysgarage3281
2 жыл бұрын
Possibly, but watch out for the PCV valve in the rocker cover. The Zafira suffer from drawing air in there causing a lean condition 🤔🤔 Let me know how you get on 🙏
@Upthetoon2010
2 жыл бұрын
Will do. I got a PCV valve on order and if the code still comes up then I will be replacing the rocker cover.
@user-kr6si1pl7v
Жыл бұрын
Cheers mate think i might have this problem ill keep u all update to how it gose loll
@kennedysgarage3281
Жыл бұрын
Please do 🙏🙏
@charlie5164
2 жыл бұрын
Great video Didn't know you could use a diagnostic to find such faults keep it up!
@kennedysgarage3281
2 жыл бұрын
Fuel trims are key to finding a lot of issues on petrol engines 🙏👍
@richardmounfield7822
3 жыл бұрын
Popped over from Daves channel . Great vid had a few of these first one had me scatching my head for a while but once you know its ruled out early on
@kennedysgarage3281
3 жыл бұрын
This one got toilet roll in the check engine light by who ever was at it before me to fix it 😂😂
@kennedysgarage3281
3 жыл бұрын
Check it out 🤔 kzitem.infoJCsee3uOKGg?feature=share
@ronaldmaxwell4579
2 жыл бұрын
Very informative liked and subscribed
@kennedysgarage3281
2 жыл бұрын
Thank you very much Ronald 🙏👍
@d.d4184
3 жыл бұрын
Well done Peter. I have been bitten in the ass with the blueprint junk.
@kennedysgarage3281
3 жыл бұрын
Yes, I do find O.E electrical parts are the best way to go but on this occasion opted for the aftermarket alternative to keep the bill as low as possible 🤔👍
@zeddytd
2 жыл бұрын
great explanation, cheers bud
@kennedysgarage3281
2 жыл бұрын
Thank you zeddytd 🙏🙏👍
@MrCountryhead
3 жыл бұрын
Enjoy your videos your well switched on
@kennedysgarage3281
3 жыл бұрын
Thank you very much, nice to have you viewing them & I hope you find some of them helpful 👍
@ssingh7043
2 жыл бұрын
Thanks for knowledge
@kennedysgarage3281
2 жыл бұрын
You are very welcome 🙏 👍
@kevinpalmer7452
3 жыл бұрын
Very well explained Peter 👍
@kennedysgarage3281
3 жыл бұрын
Thanks Kevin 😉
@kharali3475
2 жыл бұрын
I have the same problem, I think u may have helped me solve my problem mate, thanks pal
@kennedysgarage3281
2 жыл бұрын
Hopefully Khar🤞 Let me know 😉
@kharali3475
2 жыл бұрын
@@kennedysgarage3281 I just checked my engine it’s a z14zep it don’t have the pvc valve it has 2 breather pipes that goes into the rocker cover, my problem is exactly the same as your, can’t find any air leaks, changed o2 sensor still reading stft at +25 and stays like that untill I rev it to above 2000rpm it goes back to normal? Any ideas mate Thanks
@kennedysgarage3281
2 жыл бұрын
@@kharali3475 I can’t be specific but I do know that that engine suffers from air being drawn into the crankcase through the rocker cover & then causes a lean condition through the crankcase breather pipe. So wherever the crankcase pipe from the rocker cover or crankcase joins into the air intake pipe from the air box to intake manifold, block it somehow. By crimping it or remove it and block it at the air intake side. Does that make sense? 🤞
@kharali3475
2 жыл бұрын
@@kennedysgarage3281 yes it makes sense, if I restrict the air a a-bit should then be the correct air/fuel ratio, and then check where the pipe goes to Thanks I will keep u posted tomorrow
@prawny12009
Жыл бұрын
Had a dual vvt car in with a failed timing chain tensioner and guides, all inlet valves bent and rear most cam journal ruined. The upper guide runner had cracked reducing oil pressure to the head. Replaced chain and head rebuilt the car only to find out it idled like crap and smoked line a tank, initially MAF sensor fault then o2 sensor voltage fault codes, cleaned and tested resistance etc and was happy to say they were not the issue i cleaned the earth to the coils and the main battery post earth just in case with no change. Replaced the faulty purge valve and reset fuel trim which helped and seemed to get rid of the 02 sensor fault codes but started throwing fuel trim codes. All the manifold gaskets and rocker cover gasket had been renewed but there was a squeeling from the rocker cover, I expected the pcv diaphragm to be faulty but no. It turned out the pattern rocker cover gasket wasn't sealing, I dug the old one out the bin ran some fresh sealer where needed bolted it all back together and it idles perfectly now with no plumes of smoke. Let it cool down completely reset 02 heater learning, fuel trim and idle learning and the car is good to go.
@kennedysgarage3281
Жыл бұрын
😂😂😂 they can give you the runaround at times. I have been there and bought the t-shirt , then every 20 minutes the customer ringing to see what’s wrong & you pulling your hair not knowing what’s going on 😤 Very well done on getting to the end of this one 💪💪
Пікірлер: 62