I hate to tell you, but both sensors in the front of the valve body are input speed sensors one and two. The output speed sensor bolts to the back of the transmission and takes it's signal of the park pawl. You have to remove the extension housing to replace it. I did that already and that is how I know it's there. That didn't fix it and I ended up having to replace the TCM on the valve body. Here's the thing, there is a lot of "refurbished TCMs and valve bodies available on Ebay and they are dirt cheap. You get what you pay for. If you scroll down you will notice that all of them are made in China. If you like doing the same job twice then that is what you will buy.
@brownmechanicsdxb
12 күн бұрын
@@TrinityParaziader hi mate I always prefer to buy valve body from Nissan I did this before 2 time after market valve bodies are wasted.by the way I never seen input sensor outside in these models i think 1 you are talking about it’s crank sensor with 3 wires
@Aesthetics622
6 ай бұрын
I have a 2010 Nissan Murano 3.5l and the key” yellow light stays on” thinking it’s the Imobilizer ignition, but scanned the car and it shows me Output Speed Sensor Circuit p0720 -Open or short in the Speed sensor circuit. -Faulty Speed sensor. Because the yellow key sign stays solid why would it be a speed sensor?? What would you recommend to replace?? The Imobilizer or the speed sensor?? It’s got 130k on it replaced a good amount of parts recently throttle body, mas sensor, starter, coils, sparks, battery, will do alternator soon just doing this so I can make sure I don’t run into any issues in the long run as they did not look like they been replaced for a while. Any feedback is much appreciated
@brownmechanicsdxb
6 ай бұрын
If the key yellow lights stay on its mean you have issue with streeing lock motor.
@jattlifevlogs8905
Жыл бұрын
👍👍👍👍
@psycho9990
Жыл бұрын
I'm having rhe same symothons on my g37 do I need to replace just the tcm or valve body?
@brownmechanicsdxb
Жыл бұрын
Do you have same falut code
@fahadhamdan4426
Жыл бұрын
I got same this issue yesterday on my car QX50, it's means same problem!! I have to change the valvebody or sensors only Please inform me I checked I got same code P0720
@brownmechanicsdxb
Жыл бұрын
@@fahadhamdan4426 yes it’s can
@mohammedabdulla8494
4 ай бұрын
@@brownmechanicsdxbi have got the same exact issue that mr. fahad’s got it. I have got infiniti qx50 with same problem code .. so can i only change the speed sensor (the small black part with the 2 pins or i have to change the whole control module?
@brownmechanicsdxb
4 ай бұрын
@@mohammedabdulla8494 yes if it’s located outside the valve body.only switch can be replaced this car have built in sensor that’s why I replaced full control valve
@jercelabellana2396
Жыл бұрын
Do u need to reprogram the tcm that comes with new valve body?
@brownmechanicsdxb
Жыл бұрын
Not required
@Erik9264581
11 ай бұрын
as long as its the same stock VB, if you use another model (ex. Q50 Q60 G37) then yes it will need reprogram.
@Berto3.7
5 күн бұрын
@@Erik9264581 do you know if i need to program my 3.7 q50 i swap it to a 2019 3.0 trans and its drives shifts hard when going to gears and car doesn't go pass 80 or after 3th- 4th gear
@KWADONE
Жыл бұрын
Same issue with my Q50 I replaced the speed sensor and I’m still having the same code pop up Does this mean the tranny needs replaced?
@akdov9149
Жыл бұрын
been doing research and suppose that you have to change the valve body , lmk if you have figured anything out , having that issue right now on my q50
@R-A-H_-
Жыл бұрын
If you have changed the valve body, and code still pops up then it’s time to change transmission. People often change the transmission before spending money on a new valve body with a new sensor, it’s more convenient. And it’s 50/50 with changing the valve body. So your wasting money if the new valve body doesn’t work, you can spend 1k on a new transmission and never have the code again
@R-A-H_-
Жыл бұрын
And no, neither changing the valve body and transmission won’t need to be programmed, unless you get the wrong part
@joseisraelmejia1174
Жыл бұрын
i have a infinity g37x 2012 and the speedmenter doesn’t work but i don’t have any lights on it’s just doesn’t show me my speed
@brownmechanicsdxb
11 ай бұрын
If ECU getting speed signals trough Abs it’s will shift the gear.check the fuses or might be instrument cluster have problem but first you have to check speed signals trough obd
@Sweeney-ve9uu
Жыл бұрын
I have infinity qx4 2000 and my part looks way different can you tell me is it the same or not thanks a lot
@brownmechanicsdxb
Жыл бұрын
I think its 2 wire sensor located on the transmission before the propeller shaft
@Sweeney-ve9uu
Жыл бұрын
@@brownmechanicsdxb thanks
@Cookieboii
11 ай бұрын
I’m having the same issue with my 2015 q50 base 3.7 I replaced the speed sensor but I have the same issue
@brownmechanicsdxb
11 ай бұрын
Did you check the wiring harness or found any metal particles in transmission oil
@albdabs710
10 ай бұрын
I’m having the same problem and it’s 65k miles on the trans , all my friends are recommending a different transmission not from q50 but eithe g37 or vr30
@12MRJERSEY
7 ай бұрын
@@albdabs710It's the TCM, not the transmission.
@albdabs710
6 ай бұрын
@@12MRJERSEYyessir but a new tcm cost just as much what the shop charged me for Vr30 trans swap on my car, I wasn’t gonna run the same tcm just to go through the same problem again that is very common with the 3.7 trans
@busalove2013
6 ай бұрын
@@12MRJERSEY. It's the valve body! Very expensive!
@mohammedikramulla
9 ай бұрын
What is the name of your workshop in al qouz??
@brownmechanicsdxb
8 ай бұрын
Takumi motoren
@mujtuu
4 ай бұрын
hello bother i have a 2013 nissan patrol platinum its sometimes not shifting gears and showing 4wd light, i already change the acuator motor but still problem doenst shift properly help me
@brownmechanicsdxb
4 ай бұрын
In platinum most of the time wiring issues come up try to check the complete wiring harness between TCM and transmission/4WD underneath
@mj12mj
3 ай бұрын
Hello brother I change the full gear for my Nissan patrol platinum and still this code showing (I installed used transmission) kindly help me out what can be the problem now?
@brownmechanicsdxb
3 ай бұрын
Do have problem in shifting I mean you changed because of only fault code
@mj12mj
3 ай бұрын
@@brownmechanicsdxb car was stuck in 3rd gear didn’t go to 4tg
@christiandc5260
10 ай бұрын
Will this fix p0733?
@brownmechanicsdxb
10 ай бұрын
I don’t think so Generally this falut code comes once gear 3 mechanically damge
@dannyt2892
3 ай бұрын
I just did this job and did not work i also changed the sensor ...fml noyhing
@kyenross2804
Ай бұрын
Anyone ever have a p1721 code?
@KEVIN-qr2od
4 күн бұрын
Me and idk how tf to fix it😂
@kyenross2804
3 күн бұрын
@@KEVIN-qr2od same 😂
@x6z0a4v
Жыл бұрын
Nah bro speed sensor code popped up on my 25 gawd I hope I don’t have to get a whole new thing I’m just trying to start driving man it’s hard to find parts and videos for a car that was only made for 2 years😭
@brownmechanicsdxb
11 ай бұрын
Yes it can be replace only speed sensor but before you need to check properly the falut and live data
@g37mark
5 ай бұрын
I’m getting p0725
@brownmechanicsdxb
5 ай бұрын
Is car starting normally I mean any delay or long cranking
@g37mark
5 ай бұрын
@@brownmechanicsdxbstill starts normal no delay or long cranking it just shuts off after putting it into drive out coming to a complete stop
@syedrahman4096
11 ай бұрын
I also have the fault code P0720(Output Speed Sensor) and P1815 (M-Mode Switch). Please share your number and how can I contact you ?
@brownmechanicsdxb
11 ай бұрын
Jobsecretauto@gmail.com send me mail
@bosnad7766
Жыл бұрын
I have same fault, i want to bring my car to your carage, can you till where is your location in dubai and your contact number please?
@brownmechanicsdxb
Жыл бұрын
Al Quoz 1
@mohammedabdulla8494
4 ай бұрын
i have got the same exact issue in my Qx50 - model: 2015 Error: p0720 I have got infiniti qx50 with same problem code .. so the question here can i only change the speed sensor (the small black part with the 2 pins or i have to change the whole control module?
Пікірлер: 57