Thanks man, for your video your a life saver. Just dropped mine down today and had the same problem and the brake on the same spot!
@curtiswilson2126
3 жыл бұрын
Thank you for this video, I have never taken anything apart praying for it to be broken..lol
@kochj0713
9 ай бұрын
Thank you for video. Same issue on my truck… it would happen on off type.. and then work. It is def. The issue w/o taking apart
@JoseMartinez-zi4km
3 жыл бұрын
Great diagnostics. I wish this video was made 5 years ago.
@johnhale5271
Жыл бұрын
Thank you. Had the exact same issue. Fixed it myself.
@Daniel-xb4yb
9 ай бұрын
Thank you have the same exact issue
@samiam5557
4 жыл бұрын
Thanks man, I just got a P1757 code and its intermittent so I bet ya I have the same problem.
@partsshooter
4 жыл бұрын
Wouldn't surprise me! Lol My brothers truck work properly rarely, once I repaired, never had issues since. Until recently the transfer case broke again! But this repair is legit and lasted several months
@jamesshaq10
Жыл бұрын
Good evening. Your video that you made three years ago. I would like to know if your soldering iron job is still holding up. I have the same problem with my titan. Thanks in advance!
@Froggywentaknitting
3 жыл бұрын
Running your videos
@jeremycunningham558
Жыл бұрын
How much fluid did it take to refill it
@enockbabin3380
3 жыл бұрын
I need help with this on a infiniti
@razerray2454
4 жыл бұрын
If you don’t mind me asking what type of solder wire did you use and what temperature rate is it?
@partsshooter
4 жыл бұрын
Apologies, I didn't see your other comment! I get regular comments, some notify me while others don't. To answer your question, I don't have specifics on solder, however the one used was purchase from O'Reilly's auto. Whats not mentioned in the video is me testing it several times, wiggle test. It broke once so I resoldered. I read one person wrapped wire around the break to generate a conductive brace and then soldered. I can't imagine temp being the issue, just a combination of vibration with inferior weak point. Where you concerned about trans temp damaging solder?
@razerray2454
4 жыл бұрын
Yes I was concerned of the temperature transmission temperature. Hey also when you put that plastic black cover over the motherboard ( I don’t think that’s the name of it lol) did you reseal it back with some kind of special silicone like the red colored one it has on some areas?
@trsdepotllc9393
3 жыл бұрын
Can you reprogram this without having to dish out $700 by taking it to the dealership?
@doppler3237
Жыл бұрын
good video except for the constant sniffle, liked anyway.
@partsshooter
Жыл бұрын
Lol... as long as you didn't hear me swallow it
@davidd6854
2 жыл бұрын
Maybe someone can help me here. I have a 2005 Nissan Titan and when u take off from a dead stop it’s like the transmission is in the highest gear. Once u get going a bit it’s fine but it never shifts. It’s not slipping but just revs up high when u take off. I’m fairly familiar with older transmission valve bodies but not with these computer controlled newer ones like this. Thanks in advance!
@vosolocov1003
2 жыл бұрын
Im looking at this video having the same issue than you
@vosolocov1003
2 жыл бұрын
Did you fix that problem allready? And how?
@davidd6854
2 жыл бұрын
@@vosolocov1003 no I haven’t made the repair yet but positive it’s the TCM. Just don’t know if I’m going to just replace that or just get a new transmission.
@MrBiggDaddy6573
Жыл бұрын
Did either of you figure out what was wrong? Were you able to fix it?
@jubreakitjuboughtit4236
3 жыл бұрын
rock auto parts are crap
@partsshooter
3 жыл бұрын
I don't disagree... However, they offer a variety of options for part selection
Пікірлер: 25