Grbl_ESP32 now supports the P2 series inverter through RS485.
@huanyanginverter6516
3 жыл бұрын
OK usable
@kestiboy2241
4 жыл бұрын
Informative video. You can also show how to control the relay. What is the maximum power the relay can withstand? Can I connect a vacuum cleaner to it?
@huanyanginverter6516
4 жыл бұрын
Can only drive three-phase motors
@GraphicManInnovations
2 жыл бұрын
very good, is the schematic available for the main board? or at least a picture for it, i smoked main resistors on the main board and I cant find out their value, on email they are not responding, plz help, thanks
@huanyanginverter6516
2 жыл бұрын
xwdnzyp@163.com you send me an email,
@huanyanginverter6516
2 жыл бұрын
I did not receive your email i can't reach you
@GraphicManInnovations
2 жыл бұрын
@@huanyanginverter6516 i just got your email reply now, will send you right away, thank you very much for the reminder, never saw your first reply unless now
@GraphicManInnovations
2 жыл бұрын
@@huanyanginverter6516 email sent
@galichax999
4 жыл бұрын
Thanks you for your answer but this video's not the good one . My HY serial finish by d223b -2.2kw-220v Its been 3-4days i try to make it work on my NcStudio software but it wont work ,i think my wired are good ....GCM-s,m,fspeed but with the set-up PD00ect...i have try dont work So if you can send me the programmation for all the PD i need for NcStudio you'll be realy helpfully ! Thanks ! If this video was for me i will find it realy useful .
@@huanyanginverter6516 do you know how with NcStudio ?
@galichax999
3 жыл бұрын
I find a way for 3speed .thats it ?
@huanyanginverter6516
3 жыл бұрын
@@galichax999 There are up to eight speeds.
@huanyanginverter6516
3 жыл бұрын
@@galichax999 I don't understand NcStudio? Send me the schematic
@kestiboy2241
3 жыл бұрын
Hello. An error has appeared on the E.oCH inverter. What does this error mean and how can I fix it? I do not understand what is wrong, everything worked for almost a year.
@huanyanginverter6516
3 жыл бұрын
This is an alarm for excessive current.
@kestiboy2241
3 жыл бұрын
@@huanyanginverter6516 Did I set the wrong motor current in the settings? Auto tuning of engine parameters will help solve this problem? Thanks for the tip.
@stefandebruijn3167
3 жыл бұрын
@@huanyanginverter6516 Excessive current _where_? I also get this error.
@huanyanginverter6516
3 жыл бұрын
@@stefandebruijn3167 You take a video and send it to me Email:xwdnzyp@163.com
@huanyanginverter6516
3 жыл бұрын
@@kestiboy2241 You take a video of the process and let me watch email:xwdnzyp@163.com
@Proskurin_CNC
4 жыл бұрын
resistor 2W, 5k ok?
@huanyanginverter6516
4 жыл бұрын
OK
@Proskurin_CNC
4 жыл бұрын
@@huanyanginverter6516 Hey. There is a problem with the relay. TB-TC contacts are normally closed. When the spindle starts, they open. It's good. TA-TC contacts are normally open. When the spindle starts, they do not close. They must be locked. What is the problem?
Пікірлер: 28