I have just made this and it's working perfectly. Thank you Sir for sharing!! Well done.
@hashincludeelectronics
2 жыл бұрын
I am glad that it worked perfectly well 👌🏻👏🏻. Good job 👍🏻
@laggygamer4
Жыл бұрын
hlw brother mine is not working perfectly can u help me
@MuhammadRidho-qu9ey
6 ай бұрын
@@hashincludeelectronics I can't access the IP address. What's the problem with the IP? Is it a bug/error?
@hindgaming_
11 ай бұрын
Bro I am providing it 5v supply but I think it's less than 2 A. Since I am not using sevo but still the video is freezed. Is it because of A? Is it necessary to provide 2A for video streaming
@hashincludeelectronics
11 ай бұрын
You need to change one setting in code . Please check for this step in video 👍🏻👏🏻
@paulpomme2502
3 ай бұрын
Thank you very much. I haven't tried the code yet, but I'm sure it will be fine. However, I had to file down the servo horns a lot to make them fit in their places. Length-wise it's not a problem, it's the width. And the holes don't match up. I've ordered other models for the next one ;) - Actually, I'm going to build the vehicle shown in the other video, but I prefer to separate the steps. Projects: general surveillance and scaring pigeons.
@hashincludeelectronics
3 ай бұрын
Thanks for checking out the video 👍🏻👏🏻. Good luck for your project . 🙂
@KRNFF777
2 ай бұрын
the servo motor you used were from miuzi and the link you provided was tower pro which i bought and were totally useless. can you provide link for the miuzi servo motors. can you tell me where you buy parts from
@hashincludeelectronics
2 ай бұрын
You can buy any micro servo motor 👍🏻👏🏻
@iitztanz
7 ай бұрын
I have a question: if I want to use only one servo motor, then add a PIR sensor and a piezo buzzer, do I also need dummy pins for each component? Or are dummy pins only necessary for the servo motor? Thank you, please answer.
@hashincludeelectronics
7 ай бұрын
We don’t need dummy pins for other components 👍🏻👏🏻
@joshuaolaiya
Жыл бұрын
I want to build this project so I can connect to it any place in the world. Can I use an external internet access for the esp32 cam instead of my phone so I can have acces to it anywhere in the world and can I be able to control the servo any place in the world? Thanks
@hashincludeelectronics
Жыл бұрын
Unfortunately it can not be done using this project . This camera can be accessed locally only . You need to use the party apps like Blynk to access the camera globally from anywhere in the world . Unfortunately I don’t have video using Blynk on my channel . You can check for reference on internet . 👌🏻👏🏻
@joshuaolaiya
Жыл бұрын
@@hashincludeelectronics Okay. I thought it is webserver connected already. For example, I just need a router for the esp32 cam then while internet connected it streamed the video live to my phone at another country after turning ON my mobile data. Also, why is blynk different from this. I think they plan the same source as you either need a web or app so you can stream the live video.
@hashincludeelectronics
Жыл бұрын
@@joshuaolaiya you can not connect to your local routers IP from outside . And even though you open port externally somehow , it’s dangerous . When using Blynk we send data to Blynk server first . And then from mobile we connect to Blynk server and receive the data.
@joshuaolaiya
Жыл бұрын
@@hashincludeelectronics Alright noted. Thank you
@hashincludeelectronics
Жыл бұрын
@@joshuaolaiya welcome 👍🏻
@OFFICIAL_27_11_FAILURE
Жыл бұрын
Hello sir.... I have also made it looking like this. But problem is coming. The video is not playing and stops after showing only 1 second and the servo motor is also not running. Only the LED function is working.
@OFFICIAL_27_11_FAILURE
Жыл бұрын
What is causing this problem? Why is this happening? And why is the camera module ESP 32 getting hit?
@hashincludeelectronics
Жыл бұрын
You need to change one setting in code . Max messages queued . Please check this in video 👍🏻👏🏻
@OFFICIAL_27_11_FAILURE
Жыл бұрын
@@hashincludeelectronics 32 to 1
@OFFICIAL_27_11_FAILURE
Жыл бұрын
I have done this also
@donaldkormos5529
2 жыл бұрын
Could this be modified to use with 360 degree servo to get 360 degree pan capability? Thanks for your attention.
@hashincludeelectronics
2 жыл бұрын
Yes it can be. Just change the slider values in code. min and max values for pan slider to 0-360.
@donaldkormos5529
2 жыл бұрын
@@hashincludeelectronics Thank you very much for your reply. Ask because of my intended model train application. I'd like to mount on model train flatcar ... it would be nice to see forward, backward as well as right and left as train goes around layout.
@hindgaming_
11 ай бұрын
I am a newei and I have got an another problem 😅 Now the video gets freezed whenever I try to stream the video. Also I am only able to use it when I am connecting it through arduino to laptop. ESP32 doesn't start when I power it external 5v supply without the RX, TX pins. It's only working when I am connecting the RX, TX pins of arduino with it.
@thebokaguy
Жыл бұрын
I need to use the same on drone for movement, but the components have more weight than I need. Any alternatives, you can suggest?
@ksatish381
Жыл бұрын
Bro this is Bluetooth operated right or u have to give the live connection to the Arduino
@hashincludeelectronics
Жыл бұрын
This is WiFi operated. But you don’t need internet for this . This project creates its own WiFi network .
@ksatish381
Жыл бұрын
Oh tht nice but can u explain the Arduino part i tried but it failed i didn't know how to do it . If u could help me I will be very thankful I will try the robotic arm which u have made its was awesome ur explanation tho it's nice bro Tho i have a doubt i wanted to purchase a 4DOF robotic arm is tht code applicable for tht which is a 3DoF Those both look quite similar pls reply sir❣️
@muhammadsalem9924
Жыл бұрын
I want to implement this project: "Design of Driver Awareness system depending on Eye and Face Feature and Discrimination" Can I use ESP32 instead of Raspberry Pi ? please reply
@hashincludeelectronics
Жыл бұрын
You can use esp32cam however you will have to do more study on how to use it for object detection etc . 👍🏻👏🏻please check details on internet available 👍🏻
@muhamadilham3061
10 ай бұрын
Hey there I'm having a problem with the live video it doesn't seem to be showing up for me. I've also noticed that the servo doesnt work even though i've followed all of you instructions in the video including the max messages queue and reupload the code
@hashincludeelectronics
10 ай бұрын
Check the connections please 👍🏻👏🏻
@laurenceandremagsino1022
11 ай бұрын
great work! I have a question: Does it need to be on the same Wi-Fi network? I want to control it from a distance. Do you have any suggestions on how I could do that?
@erment55
10 ай бұрын
yes,it needs to be on the same wi-fi network and you need another outsourced server to control it more remotely like blynk..
@kunalsharma7890
Ай бұрын
Sir i have one doubt can we use vr glasses and headtracking to control pan and tilt can you please tell i want to add fpv vr setup in my f22 plane
@hashincludeelectronics
26 күн бұрын
Yes we can do . However it’s very complex project and currently I don’t have bandwidth for it 👍🏻👏🏻
@johnhammond3605
2 жыл бұрын
I have a basic question.i m getting a esp32 board..... should i get the cam version or the plain esp32.....does the cam version have all the functionality of normal esp32...since number of pins in esp cam are half the number of non cam version
@hashincludeelectronics
2 жыл бұрын
It depends upon your project need . Does your project need camera in it ? If yes then go for esp32cam . Else if you are starting with esp32 then buy simple esp32 module of 38 pins . Yes both the modules will almost function same with esp32 having far more number of pins than cam module.
@nh65asd26
6 ай бұрын
hi nice video, can you explain more why we need the dummy servos for the libraries to not interfere ? i am attempting a similar project, and i notice that when my servos are connected, the esp32 fails and continuously reboots.
@hashincludeelectronics
6 ай бұрын
Actually it was to avoid the conflict between timers used by servo and cam . But if you check my recent videos we don’t need dummy servos at all . I have fixed that problem . 👍🏻👏🏻
@nh65asd26
6 ай бұрын
@@hashincludeelectronics nice. I found you can also fix it by not using the servo library, and using delays for software PWM
@suneetasandeep
Жыл бұрын
Hi, Great project, i have build one and both the servos are woking fine. but the video is not coming and if coming its just a snpshot only. in serial monitor i am getting "Frame buffer could not be aquired" please suggest on how to resolve this. Thanks
@hashincludeelectronics
Жыл бұрын
Thanks for checking out the video 👍🏻👏🏻. You need to set one parameter as shown in video . Please check video and see how to set “max messages queued” variable . 👍🏻that will solve the issue .
@laggygamer4
Жыл бұрын
hi sandeep, did your problem got solved because i am facing the same problem
@naufalalghifari537
10 ай бұрын
@@hashincludeelectronics hi me too facing the same problem, i follow the step " 32 to 1 " but the problem still goes
@kitlinghou6848
2 жыл бұрын
can i use li-battery3.7vx3 (850mahx3) for this testing ? because i found my 2 servo has no any motion.
@hashincludeelectronics
2 жыл бұрын
Yea you can 👍🏻
@worldinyourhand0
2 жыл бұрын
hello bro, which recommended adapter? 5v, 9v or 12v??? (and where is the arduino with esp32 diagram?)
@hashincludeelectronics
2 жыл бұрын
1. Use Only 5v DC output adapter . 2. This diagram is there is the same link
@worldinyourhand0
2 жыл бұрын
okay ty
@hashincludeelectronics
2 жыл бұрын
@@worldinyourhand0 👍🏻
@Manash_BG
Жыл бұрын
Sorry sir I commented again since u didn't reply to my last answer I gaved Can u please explain me how to increase the range of it
@hashincludeelectronics
Жыл бұрын
You can add antenna to esp32 cam module . However you need to check for this step on internet 👍🏻👏🏻
@Manash_BG
6 ай бұрын
@@hashincludeelectronicsreplying after 5 month thanks it was really useful
@christinang478
Жыл бұрын
Can I combine this project with your other video named “Surveillance Car using ESP32 Camera Module"? If yes, what should be the changes that will occur in its code and the wiring
@hashincludeelectronics
Жыл бұрын
There is already a video on my channel where I have used pan tilt camera in car . Please check that 👍🏻
@OnojafeSamuel
Жыл бұрын
@@hashincludeelectronics Can I get the model for the 3D printing?
@nadeeshwaluskar4621
10 ай бұрын
hello! as soon as i saw this video i wanted to make this project, but i am stuck in middle. the issue is that cam module is not streaming the video instead it is just capturing a image at that instance when it is getting connected to my phone. What should i do ? please help me.
@hashincludeelectronics
10 ай бұрын
You need to update one setting related max queued messages . Please check the video for this step 👍🏻👏🏻
@zbll2406
2 жыл бұрын
This video is ultra mega useful thank you!
@hashincludeelectronics
2 жыл бұрын
Glad you think so!
@anatoledaunay6899
2 жыл бұрын
can you add 2 buttons below the sliders
@skrajupuli
Жыл бұрын
Ultra mega pro Max plus useful
@javieramayav7533
2 жыл бұрын
Hi, thanks for your great ideas, I have a question, I never see the NowISeeyou SSID, how am I suppose to get that?
@hashincludeelectronics
2 жыл бұрын
Thanks for checking out the video. You need to upload the code into esp32cam module and restart it. Once done try to see if its available in wifi in your mobile. If not then try restarting your Wi-Fi on mobile.
@sma_knk3207
7 ай бұрын
Hello friend, first of all, the project you have made is very nice, I congratulate you and I have a question for you. I will move this system to the v4 port of my modem. I need to connect it to the modem. What changes should I make in the code to connect it to the modem?
@hashincludeelectronics
6 ай бұрын
Thank you very much for your nice comment . 👍🏻👏🏻. To answer your question , you will have to AP WiFi mode in the code . You can check my getting started with esp32 video to see how we can connect to modem using AP mode 👍🏻👏🏻
@CrazyGaming-lw7cf
9 ай бұрын
@hashincludeelectronics Awesome video brother thnx for sharing this but i have a question what is the range of this model
@hashincludeelectronics
9 ай бұрын
Thank you very much for checking out the video . 👏🏻👍🏻. The range is around 60-80 ft .
@erment55
10 ай бұрын
Great job. Is it possible to add taking a picture and recording video? If yes....how I can do it?
@hashincludeelectronics
10 ай бұрын
Yes we can use SD card and store pics. But it will need lot of code changes . 👍🏻👏🏻 you can refer some material on internet for this 👍🏻
@dhananjayakarunarathne6901
2 ай бұрын
Sir i finish the project. But pan,tilt servo and camera not working.but flash light working perfectly. What i do?
@hashincludeelectronics
2 ай бұрын
Please check the connections . Also make sure you use good power supply 👏🏻👍🏻
@NanonplayZ
4 ай бұрын
Hey do i have to set the servo to 90 degree before assembly?
@hashincludeelectronics
4 ай бұрын
Yes . It should be at center 👏🏻👍🏻
@NanonplayZ
4 ай бұрын
@@hashincludeelectronics thanks and also how do find a esp cam with a cam that can position 90 like yours mine is vertical
@hashincludeelectronics
4 ай бұрын
@@NanonplayZ not sure . I just got that online from Amazon . 👍🏻👏🏻
@NanonplayZ
4 ай бұрын
@@hashincludeelectronics thanks
@hashincludeelectronics
4 ай бұрын
@@NanonplayZ welcome 🙏
@SyedIbrahim-hv3je
7 күн бұрын
Can we use this with nrog and stream the video from anywhere in the world
@hashincludeelectronics
6 күн бұрын
That would be interesting to see . Give it a try 👍🏻👏🏻
@SyedIbrahim-hv3je
5 күн бұрын
No broh can u make that happen if possible please let me know how to do so I had just ordered the esp32 and iam a fresher I don't know any thing about it
@thibault_4705
6 ай бұрын
Hello ! Mine is bugged, it connects but the image doesn't refresh. Is there a way to fix it plz ? Thanks !
@hashincludeelectronics
6 ай бұрын
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
@mdprojects9502
Жыл бұрын
Bro what is the amp of 5v ac-dc adapter
@hashincludeelectronics
Жыл бұрын
It should be more than 2A .
@mdprojects9502
Жыл бұрын
Thank you bro
@mdprojects9502
Жыл бұрын
Can we use mobile charger with 5v 3A
@Takeover738
7 ай бұрын
Uploaded the code but camera just doesn't stream all I get is frozen still pic. Do you have a solution for this problem? great vudeo
@hashincludeelectronics
7 ай бұрын
You need update one setting in code . Please check the video for this step 👍🏻👏🏻
@Takeover738
6 ай бұрын
I got it working i was trying to get the esp32 to connect to my router but no luck
@tonyp4894
2 ай бұрын
I accidentally erased the esp32 json file in preferences, so i searched for the url again and loaded it. NOW, using the same code as yours, all I get is "Error compiling for board AI Thinker ESP32-CAM. " Please guide me to a solution as I have exhausted everything that I can think of. I noticed that if I use WebServer, instead of AsyncWebServer, the code installs without error, but the images do no work. HELP !!!
@hashincludeelectronics
2 ай бұрын
Which version of esp32 did you install ? Please install only 2.0.16 version of esp32 board 👍🏻👍🏻
@Manash_BG
Жыл бұрын
Thanks sir , since I have made a drone I want to add a camera which can record and send to phone but there is no video of it soo i searched for wireless cctv and this was helpful I can add it to my drone soo i can stream in phone thank you sir also can u pls Say me how to make the camera and the phone connection range long
@hashincludeelectronics
Жыл бұрын
Thanks for checking out the video 👏🏻👍🏻. It’s nice to hear that you are working on drone and want to add camera functionality in it . However this project has very limited range like wifi . However if you want to increase the range then you might have to connect the antenna. 👏🏻👍🏻
@Manash_BG
Жыл бұрын
@@hashincludeelectronics Can u make a video about it soo i can understand clearly since I don't know properly of making things because I don't have the essential required stuff
@omarescobedo5323
11 ай бұрын
Hello i need help, when i try to compile the code, it appears the error 'class AsyncWebSocketClient' has no member named 'queueIsFull' 🤔🤔
@hashincludeelectronics
11 ай бұрын
Have you downloaded the correct library and version ? Please uninstall any previously installed library and install again 👍🏻👏🏻
@laggygamer4
Жыл бұрын
hlw sir i am facing a problem... it is that the video is not streaming and when it streams its just a snapshot only and then it freezes and i cant help it...the serial monitor says frame buffer not accquired... i have also set the parameter to 1 as described in the video... plzzz reply sir plz help me
@hashincludeelectronics
Жыл бұрын
Please recompile the code and upload again . And then try 👍🏻👏🏻
@techvishalnewsdevelopers309
Жыл бұрын
Unable to upload code at all with ft232r module so i have ordered cp2102 usb to ttl module
@joseramonbarajashernandez4463
11 ай бұрын
Hello, good video, where can I get the structure of the servos and the esp32cam camera?
@hashincludeelectronics
11 ай бұрын
Sorry I did not get your question.
@jimswift4718
6 ай бұрын
I am using your code and following your video. However I get an error "Frame buffer could not be acquired" What could I be doing wrong
@hashincludeelectronics
6 ай бұрын
You need to update one setting in code . Please check the cheek for this step 👍🏻👏🏻
@Secret-eo1rz
2 жыл бұрын
Good day Sir, I faced a problem which is when I try to control my servo motor it will auto disconnected the wifi connection. Is it because of the current provided to the motor doesn't enough? But for the ESP32 CAM and the lightning control works well
@hashincludeelectronics
2 жыл бұрын
Yes . Servo motors need proper current around 500 ma . So please use rechargeable battery and provide 5v to servos .
@Secret-eo1rz
2 жыл бұрын
I see ... appreciate for the reply sir 🙇
@hashincludeelectronics
2 жыл бұрын
@@Secret-eo1rz happy to help 👍🏻
@loganstombaugh1856
11 ай бұрын
Uploading the code from arduino uno to esp32 cam board is not working for me. It's saying failed to connect to the esp32 board and there is no serial data received.
@hashincludeelectronics
11 ай бұрын
Try to press enable button on that esp32 module 👍🏻👏🏻
@dienau6313
Жыл бұрын
I dont understand at 8:17 which pins do you connect in arduino uno?, and how it can connect to esp32-cam?
@hashincludeelectronics
Жыл бұрын
Please check the video slowly and also take a look at circuit diagram 👍🏻👏🏻
@joshuacabauatan4430
Жыл бұрын
Im using a 6v AA battery. Is that the reason why my camera not functioning and the prototype keeps on disconnecting?
@hashincludeelectronics
Жыл бұрын
Yes exactly. Please use rechargeable battery only .
@MuhammadRidho-qu9ey
6 ай бұрын
*HELP ME* sir 😭😭😭😭😭😭😭I can't access the IP address. What's the problem with the IP? Is it a bug/error?
@hashincludeelectronics
6 ай бұрын
Please check for loose connection. Provide proper 5 v supply only . 👍🏻👏🏻
@elmokopo8950
4 ай бұрын
This project and line follewer car combining ? How can we do
@LittleSudip
Жыл бұрын
I've tried according the video. Uploaded the code in esp32 without any error. then when I've giving power with 5v 2a adapter. SSID works. After connecting to ssid. Only LED control working. Camera video is freezed and no servo is working. I've also set the WS limit to 1. But still no movement in servos and no live video footage. Please give me a permanent solution
@hashincludeelectronics
Жыл бұрын
Please check the power supply . It should provide more than 2A current to work . Also check if your servos are freely moving . It should not get stuck in the frame 👏🏻👍🏻
@LittleSudip
Жыл бұрын
@@hashincludeelectronics okay. the servo is not moving. when i'm disconnect the 5v pin, that time the servo just giving a shaking.
@MuhammadRidho-qu9ey
6 ай бұрын
I can't access the IP address. What's the problem with the IP? Is it a bug/error?
@MuhammadRidho-qu9ey
6 ай бұрын
Help me sir
@baocunb770
2 жыл бұрын
A very nice project! I did it but only pan SERVO runs, Tilt SERVO not move, what can be? thanks.
@hashincludeelectronics
2 жыл бұрын
Thanks . Please check the connections properly . May be there is loose connection for sure .
@baocunb770
2 жыл бұрын
@@hashincludeelectronics thank you for quick reply , I did exchanged two SERVOs pin and tried all pins of ESP32CAM, only pin12 drived both SERVOS, other pin not...
@hashincludeelectronics
2 жыл бұрын
@@baocunb770 you need to use io14 and io15 only .please check the circuit diagram for pins used .
@gfxstudio2
2 ай бұрын
A compilation error is coming ' ledcsetup not declared in this scope ; did you mean ledc_stop ' Also coming for ledcattachpin How to solve ? Please help 🙏🏻
@hashincludeelectronics
2 ай бұрын
Please install 2.0.16 version of esp32 board 👍🏻👏🏻
@debmalyadas8647
Жыл бұрын
It shows connected without internet to NowISeeYou ssid. The light works well but the servos show no motion at all. Any solution??
@hashincludeelectronics
Жыл бұрын
It should be connected to this ssid only . Please check the video 👏🏻👍🏻
@Afrazsamsudeen
2 ай бұрын
I like it but which app does it use?
@hashincludeelectronics
2 ай бұрын
Thank you for checking out the video . The app is inbuilt in car code . It is made using html and JavaScript 👍🏻👏🏻
@adrian-brawlstars9296
Жыл бұрын
Hello! i get this error whenever i want to upload the code - A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header. Can you help me please?
@hashincludeelectronics
Жыл бұрын
It’s very common error . You can find more details on this error on internet 👏🏻👍🏻
@siddarthpawar2615
3 ай бұрын
esp_camera.h: No such file or directory, it shows after all what you said adding link in preferences, esp32 board downloaded, and added both libraries ASYNCTCP and websocket
@hashincludeelectronics
3 ай бұрын
Please select proper board while uploading the code 👍🏻👏🏻
@siddarthpawar2615
3 ай бұрын
@@hashincludeelectronics now getting this error-Compilation error: 'ledcSetup' was not declared in this scope; did you mean 'ledc_stop'?
@kaushalkarwa3182
Жыл бұрын
Hi sir the camera is stuck at one picture, can you help me i need this asap for a project.
@hashincludeelectronics
Жыл бұрын
Thanks for checking out the video 👍🏻👏🏻. You need to set MAX_QUEUED_MESSAGES to 1 as shown in video . Please check the video for this step . It will solve your issues 👍🏻👏🏻
@psykopat81
Жыл бұрын
Can we get images if ESP 32 is connected to the phone instead of connecting phone to ESP 32 ?
@hashincludeelectronics
11 ай бұрын
Sorry I did not get your question 👍🏻👏🏻
@psykopat81
11 ай бұрын
@@hashincludeelectronics i mean, can we use esp 32 cam station mode instead of setting it as access point ? (in your project phone connects to esp32 cam, but i want to connect esp32 cam to phone's hotspot)
@hashincludeelectronics
11 ай бұрын
@@psykopat81 yea you can . However what are you trying to achieve by doing this ? If you connect to your mobiles hotspot then you will have to get the ip address from esp32 which will be different.
@psykopat81
11 ай бұрын
@@hashincludeelectronics i am controlling my old android phone with teamviwer. If the esp32 cam is connected to the hotspot of this phone, I could control the esp 32 cam from anywhere in the world (you know blynk video streaming is now paid). If the phone is connected to the esp32 cam via wifi, the mobile connection is automatically closed and I cannot connect to my old phone. So the phone's mobile connection must remain open and esp32 must be connected to the phone.
@worldinyourhand0
2 жыл бұрын
i've issue my adapter was blinking when plugging to esp32 cam. My adapter 5v 2A just normally no problem in other. i confused in this, where's the problem..
@hashincludeelectronics
2 жыл бұрын
Remove the servos and just try connecting to esp32 only . See if it works . May be servos are causing issues .
@worldinyourhand0
2 жыл бұрын
@@hashincludeelectronics servo isn't problem i was checked and test
@worldinyourhand0
2 жыл бұрын
@@hashincludeelectronics then i press reset button esp32cam, the esp led is blinking too
@MuhammadQasim-kw1er
5 ай бұрын
HEY can i get the stl file of servo part, i know you order it online however by any chance you have it/arrange it. Thanks
@hashincludeelectronics
5 ай бұрын
Unfortunately I don’t have it 👍🏻👏🏻
@MuhammadQasim-kw1er
5 ай бұрын
@@hashincludeelectronicsThank you for your comment, no worries! I got it anyway.
@hashincludeelectronics
5 ай бұрын
@@MuhammadQasim-kw1er awesome 👍🏻
@mohammedsadiqahmad2886
2 жыл бұрын
Sir, please, I want to do it in order to add it in my graduation project. Is it possible to open this (IP website) from a place far from the esp32 piece, for example, if you are connected outside the house to a network and esp32 in my house??
@hashincludeelectronics
2 жыл бұрын
You have to be on same network for this camera and app to work. Currently it does support controlling from anywhere in the world.
@mohammedsadiqahmad2886
2 жыл бұрын
@@hashincludeelectronics This means I should stay close to the esp32 and not far away !!?
@hashincludeelectronics
2 жыл бұрын
@@mohammedsadiqahmad2886 nope . I means it will work the way your WiFi works . 70-100 ft .
@mohammedsadiqahmad2886
2 жыл бұрын
@@hashincludeelectronics Yes, I understand, thank you
@hashincludeelectronics
2 жыл бұрын
@@mohammedsadiqahmad2886 welcome 👍🏻
@ademressaissi2277
6 ай бұрын
plz i need help i keep getting this error : The esptool_py tool is not available for your operating system.
@hashincludeelectronics
6 ай бұрын
Please use Arduino IDE and install esp32 board in it 👍🏻👏🏻
@pushkarjaiswal4808
5 ай бұрын
Can u please make it gesture controlled. For example if you turn your hand around, camera should turn in same direction.
@hashincludeelectronics
5 ай бұрын
Will try 👍🏻👏🏻
@sdknstar601
2 жыл бұрын
Is that possible to replace the servo control using joystick?...and trough laptop...
@hashincludeelectronics
2 жыл бұрын
You need joystick instead of slider on the app working on laptop ? Or you need actual hardware joystick ?
@sdknstar601
2 жыл бұрын
@@hashincludeelectronics actual joyatick that run on pc my friend...is that possible?...thank you..
@hashincludeelectronics
2 жыл бұрын
@@sdknstar601 anything is possible👍🏻. But I don’t get a point when you say joystick with PC. Sorry I might be missing something here. However you can use joystick with another esp32 which is transmitter and send commands to receiver esp32cam. Simultaneously receive the video stream on PC. Or you can elaborate more on your requirement 👍🏻 I have never attached joystick directly to PC.
@sdknstar601
2 жыл бұрын
@@hashincludeelectronics kzitem.info/news/bejne/1WyKl4aQh6ajY2k I found this...but...actually i want control with usb joystick via laptop...😔
@hashincludeelectronics
2 жыл бұрын
@@sdknstar601 oh ok. I am not aware about USB joystick. If I find something I will let you know . 👍🏻
@SamanviM
9 ай бұрын
Bro is it compulsory to use AC to DC adaptor
@hashincludeelectronics
9 ай бұрын
No it’s not . But you need to provide 5v dc with more than 2A current 👍🏻👏🏻
@SamanviM
9 ай бұрын
Bro only one request can you explain this in detail pls
@NehaRaiDEC-
6 ай бұрын
Sir can you please help me I am facing an error related to AsyncTCP Library saying no such file or directory
@hashincludeelectronics
5 ай бұрын
You need to install those libraries . Please check the video for steps 👍🏻👏🏻
@rijwanjaelani5449
10 ай бұрын
how to program to record video from esp32 cam and save it on sd card
@hashincludeelectronics
9 ай бұрын
I don’t have steps for these however you can check on internet for more details. I will take a note of it and probably will create video for the same 👍🏻👏🏻
@amruthaboorti7190
Жыл бұрын
A very much useful video for the current project I'm doing. Kindly can you please tell me how this can be make possible on a drone to view and get the video. It means a lot if you would help for this. Thank you ☺️
@hashincludeelectronics
Жыл бұрын
Thank you very much for checking out the video 👍🏻. This will not have enough range for drone .
@MustafaTatl
5 ай бұрын
how can i use moibe data (i wanna not use local modem )
@hashincludeelectronics
5 ай бұрын
Please check my video on getting started with esp32 for Station mode 👍🏻👏🏻
@sumeetmurgod2211
11 ай бұрын
Thank you sir for this code and setup explanation. And i have question sir can we use a battery for power supply
@hashincludeelectronics
11 ай бұрын
Yes you can use battery . However you need to make sure battery provides exactly 5V . Also use only rechargeable battery 👍🏻👏🏻
@sumeetmurgod2211
11 ай бұрын
OK sir thank you for your guidance.
@hashincludeelectronics
11 ай бұрын
@@sumeetmurgod2211 welcome 🙏
@Moon-D0G
6 ай бұрын
How can we fine tune the Servos to be more precise or less jittery?
@hashincludeelectronics
6 ай бұрын
You can try adding some delay if possible 👍🏻👏🏻
@sumeetmurgod2211
7 ай бұрын
sir after connecting the battery i am unable to get the video and also the motors are not functioning but i am able to control the led flash light .can you tell me what device or method to be applied to get the proper output
@MehramKhan-ru1nu
7 ай бұрын
same problem
@its_ag__edits____2662
5 ай бұрын
I also got same problem please tell what can be the solution for it
@GioBen68
2 жыл бұрын
Great video. Exactly what I was looking for 👍🏼 Will use it with esphome
@hashincludeelectronics
2 жыл бұрын
Awesome 👏🏻
@MuhammadRidho-qu9ey
6 ай бұрын
@@hashincludeelectronics I can't access the IP address. What's the problem with the IP? Is it a bug/error?
@choporo2005
2 жыл бұрын
OMG, I found exactly what I wanted to do. Thank you very very much.
@hashincludeelectronics
2 жыл бұрын
That’s nice 👍🏻I am glad that it helps you .
@dbananaa
2 жыл бұрын
Thanks a lot for this video from Kazakhstan. At the moment 4.54 , what link did you write in "Additional Boards ds Manager URLs"?
@hashincludeelectronics
2 жыл бұрын
Thank you very much 👍🏻it’s link is given in the video just around 4:56. Also it’s provided in the description of the video .
@AdityaNakhare
3 жыл бұрын
Amazing...just one observation which u can consider : Camera movement is bit noisy
@hashincludeelectronics
3 жыл бұрын
Thank you for checking out the video and suggestion 👍 The noise comes from Servo motors used as these are very cheap servos and has plastic gears. It can be avoided using better servos with metal gears .
@MrHoabantrang
10 ай бұрын
I follow your guide with code but video didnot stream, the screen only a picture when camera turn on. I couldn't control pan and tilt servo, but the light can turn on or off. I used different power for ESP32 Cam and servos. Anyone can help me to solve this problem? Thankyou!
@hashincludeelectronics
10 ай бұрын
You need to update one setting max messages queued . Please check the video for details 👍🏻👏🏻
@MrHoabantrang
10 ай бұрын
@@hashincludeelectronicsIt's ready, I have changed from 32 to 1 as your guide.
@Secret-eo1rz
2 жыл бұрын
Hi sir, May i know what is the used for Arduino UNO R3 in this project? At first I tot it is used to control the servo motor then I realized the servo motor was connected to the ESP 32-CAM instead of the Arduino board
@hashincludeelectronics
2 жыл бұрын
Arduino Uno is only used to upload code into esp32 cam .
@Secret-eo1rz
2 жыл бұрын
@@hashincludeelectronics I see ... Appreciate that sir 😳
@utkarshpandey8507
2 жыл бұрын
I having an issue. Please help. It's showing No such file or directory for esp_camera.h What should I do?
@hashincludeelectronics
2 жыл бұрын
Please check the video for installation of boards
@sorathonpoahong5870
Жыл бұрын
my serial monital show"psram initialized. malloc to take memory from psram above this size" what it mean and howto fix i?
@hashincludeelectronics
11 ай бұрын
I believe you are missing some step . Please check the video for any missing step . 👍🏻👏🏻
@alibalialibeyov3277
2 жыл бұрын
please help me. When I tried to copy the code and I touch to upload button in the Arduino IDE but it didn't upload. I downloaded the Esp32 board, the AcyncTPC library, and the ESPAsyncWebServer library. Arduino's 5V is connected to 5V, GND to GND, UOT to TX, UOT to RX, RESET to GND, GPIO 0 to GND. But even if the computer sees the Arduino Uno card, it does not upload code. İt gives a "fetal error".
@hashincludeelectronics
2 жыл бұрын
Yeah this error is common . There are many solutions for this . Try pressing enable button while uploading the code . Try using different USB port . Or cable . Check on internet for information on this error . It should be solved 👍🏻
@ameerpasha9941
2 жыл бұрын
@Alibali Alibeyov bro Iam also facing same issue. Did u solved it?
@alibalialibeyov3277
2 жыл бұрын
@@ameerpasha9941 yes I was able to solve. I just changed the port of the Arduino Uno card a few times, tried to reload and it worked. That's how I solved the problem. If you solve, you write the answer;)
@ameerpasha9941
2 жыл бұрын
@@alibalialibeyov3277 bro can i have ur mobile number
@Billy_0614
6 ай бұрын
Hello, this text is showed in serial monitor "Frame buffer could not be acquired". How can I fix it?
@hashincludeelectronics
6 ай бұрын
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
@Billy_0614
5 ай бұрын
@@hashincludeelectronics I already change it, but it still does not working.
@Billy_0614
5 ай бұрын
Also the servo is not working. Can you help us? we will use it in our capstone project
@raffaelebarlotti9017
Жыл бұрын
Nice project! Could you tell me which mobile app to use? Thank you.
@hashincludeelectronics
Жыл бұрын
The mobile app code is inbuilt in Arduino code itself . It uses html and JavaScript 👌🏻👍🏻
@baraalsaeed6865
2 жыл бұрын
Firstly, thank you very much. I hope to answer me ,can I use GPIOs 4, 12, 13, 14, and 15 to connect them to servo motors ?
@hashincludeelectronics
2 жыл бұрын
Yes you can use these pins for connecting to servos .
@sakethpuppala1016
8 ай бұрын
you can not use gpio 4 bro
@nh65asd26
6 ай бұрын
its possible to disable the flash led @@sakethpuppala1016
@yashkumar2716
2 жыл бұрын
hi bro thanks for the video i just wanted to know what is the power output of your adapter because i am using normal 5v 2A charger to provide power to esp32 cam and servo but sometime it work but most of the time i get brownout error in the esp32 cam i think power is the issue but i checked it with the multimeter the power is 5v only but not sure why it is happening i am sure board is not faulty because sometimes it works when i hold the pins and move it a little in breadboard
@hashincludeelectronics
2 жыл бұрын
It’s 30 watt . Yeah that brownout issue can be due to improper power. Try the other adapter .
@yashkumar2716
2 жыл бұрын
30 watt ? Can you share any link of that adaptor I'll also try to get something similar
@hashincludeelectronics
2 жыл бұрын
@@yashkumar2716 amzn.to/3HewZcX
@hakamsingh1673
Жыл бұрын
Hello sir can we access it from internet from any remote locations
@hashincludeelectronics
Жыл бұрын
No it’s not possible in this project 👍🏻👏🏻
@subhobiswas4193
2 жыл бұрын
Please help.. When I uploaded the code after doing connection properly it was working properly. So I have disconnected the supply and I was happy. But after some time I again connected the supply and the problem starts from here. At first when I was trying to connect the wifi it connects and getting disconnected quickly. But now no hotspot is coming from the esp32 cam module as I can't see from the wifi section of my phone. So I have reset the board and uploaded the code again but still same problem. Please give me the solution.
@hashincludeelectronics
2 жыл бұрын
What power supply are you using ?
@donaldkormos5529
2 жыл бұрын
Thank you ... will be my next project to use with model trains. All the best to you!!!
@hashincludeelectronics
2 жыл бұрын
Thank you 👏🏻
@Daily_Details
Жыл бұрын
bro igot an error fatal error: esp_camera.h: No such file or directory what do i do
@hashincludeelectronics
Жыл бұрын
Please install esp32 board as shown in video . Also select proper board while uploading the code 👍🏻👏🏻
@MrAshubajpai
2 жыл бұрын
I want to add your pan and tilt code so that i can addin my existing model.... Can you plz help
@hashincludeelectronics
2 жыл бұрын
Sure. You can use the code or edit in the same code. Its free 😉
@ahmadqorom1654
Жыл бұрын
what the mobile app you used ?
@hashincludeelectronics
Жыл бұрын
Thanks for checking out the video 👍🏻. The app is created in the code itself using html and JavaScript 👌🏻
@Rayhan_Ahmed.
Жыл бұрын
Sir, I am facing this problem " esp_camera.h " file not found. Now what should I do? Please sir help me, Love from Bangladesh ❤️
@hashincludeelectronics
Жыл бұрын
Please install the esp32 board as shown in video . Also select proper board while uploading the code in Arduino IDE 👏🏻👍🏻
@DARK2SHARK
9 ай бұрын
@@Rayhan_Ahmed.Use laptop or computer
@Sky_is_the_limit03
8 ай бұрын
Well sir if I use arduino nano here instead of arduino uno.....
@hashincludeelectronics
8 ай бұрын
Yes you can 👍🏻👏🏻
@Rupali-m8f
7 ай бұрын
can we use battery instead if then how???
@hashincludeelectronics
7 ай бұрын
Please check my other videos for reference 👍🏻👏🏻
@DarioAOcampo
2 жыл бұрын
I swear to god the Tilt servo is not working. Pin 15. I've tested the servo itself and it works. I've also tested uploading other code and use pin 15 and the pin itself is working. I've checked the code several times. I've watched the video several times as well. And reading the comments I'm not the only one having this issue. Please can you focus for a minute on this issue?. BTW, I've also watched several times the wifi car pan tilt video and I've tried changing config.ledc_channel = LEDC_CHANNEL_4; config.ledc_timer = LEDC_TIMER_2; and still its not working. I really hope you can help.
@hashincludeelectronics
2 жыл бұрын
Thank you very much for checking out the video and trying it. I assure you that there is no issue on using Pin 15 for servo. 1. Make sure you upload the given code for this project again Please don't make any changes at al in code. The timer and channels are coded properly and tested well. 2. Make sure you use 5V DC Adapter which provides more than 2 A current rating. give it a try and let me know. Don't worry it should work as it worked for me .
@taramis4570
Жыл бұрын
Great video! I have a problem with during compilation on the line 246. "error: variable 'std::istringstream ss' has initializer but incomplete type std::istringstream ss(myData); ^" Do u know how I can fix it?
@hashincludeelectronics
Жыл бұрын
This error should not occur . Which Arduino IDE are you using ?
@gtprojectz
3 ай бұрын
Can recording or streaming?
@hashincludeelectronics
3 ай бұрын
No it’s not possible in this project 👍🏻👏🏻
@NHAN_VLOG
7 ай бұрын
Hey you, do you have any video how to make a webserver for esp32
@hashincludeelectronics
7 ай бұрын
You can check my video on getting started with esp32 👍🏻👏🏻
@anithhrithran7063
6 ай бұрын
Hi nice video but, The Pan and tilt servos not working when i try it. Also the video is not working I only get a still picture even after changing the setting from 32 to 1, the only thing that works is the flashlight.
@hashincludeelectronics
6 ай бұрын
Please check the video slowly and carefully for any missing step 👍🏻👏🏻
@anithhrithran7063
6 ай бұрын
Ok thanks
@diego_roca
5 ай бұрын
I'm struggling with this, for some reason the esp32 just gives me one image and then it does not update anymore and I still can't figure out why :(
@hashincludeelectronics
5 ай бұрын
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
@diego_roca
5 ай бұрын
@@hashincludeelectronics Thank you for answereing, I was indeed missing hat step, but even after fixing that it still forzes after a sew frames and then only the LED brigthess control works and also gives the message "Frame buffer could not be acquired" in the serial monitor :(
@worldinyourhand0
2 жыл бұрын
hello bro, can i control the cam from a far? because when i try then noticed it can only be connected when it's reached by esp32 cam *i mean control from anywhere
@hashincludeelectronics
2 жыл бұрын
For now it can be only controlled locally .
@worldinyourhand0
2 жыл бұрын
@@hashincludeelectronics what if the esp32 cam is connected to the home wifi, is that possible? using the same code?
@worldinyourhand0
2 жыл бұрын
if it works, can you give me a suggestion or how to do it
@hashincludeelectronics
2 жыл бұрын
@@worldinyourhand0 it’s possible. But you have to make a very small change to connect using STA WiFi mode .
@hashincludeelectronics
2 жыл бұрын
@@worldinyourhand0 check my video on esp32 getting started where I have used hone WiFi connection 👍🏻
Пікірлер: 588