If like me you would like your Pard 008S LRF lazer splash to be centre screen and not top right like mine was then here's how to adjust it . Tools you will need are a very small Philips screw driver and I little pick tool or needle . Use your pick tool and gently remove the black plastic self adhesive trim from the front of your lrf unit . behind it are 4 screws to adjust the lasers direction, the laser is held in place by the 4 screws only and has no other contact or support within the unit . Between the laser unit and the front of the metal frame/unit which it is fixed to by the 4 scaws is a thick rubber washer ,this is what gives the movement of the laser for adjustments to the splash . Making only very small adjustments to the screws at a time now adjust the angle of the laser . For up you would turn the top 2 screws equally anticlockwise, just one tenth of turn and then check it's position For down you would turn the bottom 2 screws equally clockwise one tenth of a turn and check its position. For left you would turn the 2 right side screws equally anticlockwise one tenth of turn and check its position. For right you would turn the 2 left side screws equally anticlockwise one tenth of turn and check its position. Equally depending on the tightness/compression of the rubber washer on your unit the opposite adjustment maybe needed , trail and error as long as you make small adjustments and check what the lasers direction is doing you should be OK. Now to check what the laser is doing you will need to put the unit in to night mode/ black and white , then press the lrf button to activate the laser ,look at the screen and see where the splash is and make your adjustments accordingly. Once you have it centred you then need to move the cursor/yellow box on to it . To do this in night mode press the range finder button ,now press the main menu buttom and then press and hold down the plus button until the x and y adjustment screen appears . Just like when you zeroed you unit for the first time , adjust the yellow box's position until its centred . Dead centre is x0 y0 ,but yours won't be centre unless you used something like an Eagle vision mount to zero your pard . So x0 y0 won't work for most, you move it to where you think is centre then long press the menu button to save and back out , press the lrf button again to see where the yellow box is again , then repeat until your happy with it Mines now perfectly on my crosshairs happy days . I couldn't find this info anywhere so i hope this helps someone looking to do it on there pard 008S LRF . Obviously at your own risk .
@-Anton--
2 жыл бұрын
Great! Thanks!
@IIMAVII
2 жыл бұрын
Nice one. Got myself an NV008S LRF last week and have set it all up and its been great apart from the range finder beam is much lower and to the right of the center of my crosshair. Couldn't find a way to adjust it so I will give this a go 👍
@konighansen9062
2 жыл бұрын
Do you know how to disassemble the eye box, there is a hair on my lcd screen, which is annoying
@nicholasparry2521
2 жыл бұрын
@@konighansen9062 That’s annoying pal , the only other thing I’ve done is moved the 4 screws at the rear to reconnect the red laser . This does then give access to all the internal so you maybe able to move the hair from there . If you look at the rear behind the eye peace you will see 4 screw with hex heads ,remove them to gain entry to the unit
@adriantownley7076
Жыл бұрын
cheers mate, that was a great help before my first foray out since buying the scope, fingers crossed with the weather tonight.
@cyberpunk7179
Жыл бұрын
Hi Nicholas I see you mentioned reconnecting the red dot laser is this on the 008slrf version? And is the connector in the front or back of the unit? Many thanks
@nicholasparry2521
Жыл бұрын
Yes and yes pal
@jackclarke7584
Жыл бұрын
do these have a red dot ?? and is it reactivated the same as the p series?
Пікірлер: 17