thanks...your method of painstakingly explaining every application is very helpful ... it makes the application easy ..oh... the wire that goes through the castle nut is called a cotter pin...be well...peace
@JuanVega-ns5ok
7 күн бұрын
Great video. Lots of detail. If you had taken the 3 nuts off the ball joint during removal, you probably wouldn’t have had to remove the brake caliper, although it does give you better visibilityTurning the ball joint shaft so that the hole is oriented front to back was an expert move that is not mentioned in other how-to videos. Great job. I might be doing this job in the near future. Thank you, Sir.
@elchanojose
2 күн бұрын
Hello! Thank you for taking your time to watch our video and this was the first time we replace a Toyota Camry control arm. We learn as we go. Thank you for sharing that this video is helpful. Take well care!
@josephmorgan4616
4 ай бұрын
This is a very good video. Thanks, José.
@cmasui
27 күн бұрын
Thank you! Great Job! God Bless you.
@elchanojose
26 күн бұрын
Hello! Thank you for taking your time to watch our video and for sharing that you liked our work. Take well care!
@radupreguza4270
5 ай бұрын
Thanks man! I’ll use all the information that you gave to replace the control arm for my car 🤝
@Seraphim401
5 ай бұрын
This is awesome man. Thanks for sharing your knowledge.
@JuanDiaz-vm1pv
5 ай бұрын
Extremely helpful. Muchas gracias.
@elchanojose
5 ай бұрын
Hello! Thank you for sharing after watching our video that this video was extremely helpful. Take well care!
@sauravbhatta5303
Ай бұрын
@@elchanojose22 mm bolt can’t go in. Bolt and thread in hole spin together. Any help Jose?
@marccrotty8447
Ай бұрын
Excellent presentation. Thanks.
@JuanVega-ns5ok
7 күн бұрын
Subscribed.
@elchanojose
7 күн бұрын
Hello! Thank you for visiting and subscribing to our channel. Take well care!
@sonnynguyen7327
7 ай бұрын
Oh good job men
@elchanojose
7 ай бұрын
Hello! Thank you for watching our video and for sharing that you liked our job. Take well care!
@sauravbhatta5303
Ай бұрын
My 24 mm bolts keep spinning with the bolt sleeve. Been 2 days struggling to screw these bolts. I can feel the thread on the bolt hole spinning with my finger putting it in. Any idea how can I screw these bolts? For reference these bolts joins the control arm to the bar.
@MMNcentral
Ай бұрын
I had the same issue on a 2006 Avalon 140,000 miles where the 14mm x 90 mm bolt goes thru the control arm end rubber bushing. I tried a Sawzall with good quality (Milwaukee) metal cutting blade and it did little more than make a slight groove in the bushing after several minutes and attempts at sawing through the bushing and bolt. I ended up using a Makita 4 inch angle grinder with a flat metal cutting disc to grind through the top and bottom area of the sleeve-bolt to be able to remove the control arm. It took some time to grind through and a couple of discs as the discs would wear down and lose the ability to reach fully through the bolt - sleeve. Guard was removed from grinder, gloves and a face shield are a must. Patience and Ear plugs definitely recommended. Rust on the control arm bolts make this job a miserable time consuming struggle and not one for the DIYer with minimal tools and experience! Perhaps the repair shops use a cutting torch to cut out the seized up bolt and sleeve and living with the burning rubber and smoke, but not something I was anxious to try before I tried the grinder cutting wheel operation.
@jotu173
5 ай бұрын
Shop labor hours shows roughly 2 more hours for an 08 Avalon as compared to an 08 Camry. Have you ever done a (same year) Avalon and, if so, did it take 2 more hours & why?
@SHTRU
Ай бұрын
if you follow this you probably could do it in 1hr 30mins
@jeffobi1023
3 ай бұрын
Excellent video! Thank you very much Jose. Side note: I think torque specs are very important.
Пікірлер: 22