I was on the fence about replacing my windows myself but after watching this video I am very confident that I will replace my windows myself. Thank you, this video is exactly what I needed. You hit all the details that is required to replace a window.
@TrueGritDevelopment
2 жыл бұрын
Glad it helped. Honestly, once you get going it’s pretty straight forward. Thanks for watching and supporting. Good luck with your project 👊🏼
@robertcox9226
Жыл бұрын
Totally missed what I was saying I miscommunicated in some way I don't like that it's butted behind the trim it won't seal to the trim silicone 6 months after 6 weeks after rather I could take and grab it like a rubber band and pull it out it just doesn't stick adhesion is poor I would pull the trim boards off for the extra effort and wrap the flashing down across the face of the wood and then put the trim board back on that's what I meant I don't like that where you just put it up against the baseboard and seal it I would if I was forced to do it that way I would use the water block product instead of silicone I did a threshold in an A-frame house and 20 plus years never have water from the driveway get underneath before we place the window we had that problem every time it rained hard the water block works awesome and never dries it stays gooey like bubble gum
@grizzly4736
Жыл бұрын
Same. This video makes me feel like my wife and I will able to replace our windows. Saving this video for reference.
@FrankArias-z6g
11 күн бұрын
Just installed a 150 window today, and your video made it so easy. I had looked at Pella's instructions several times and it was not clear. Thank you!
@TrueGritDevelopment
11 күн бұрын
Glad it helped 👍🏼
@jameslloyd8110
29 күн бұрын
I have my own window installing company, and this is probably the best most detailed video for installing windows. The only question I have is why you didn’t take the sashes out. I feel it makes it a lot easier to take the sashes out and install the frame then put the sashes back in.
@TrueGritDevelopment
29 күн бұрын
Thank you! Appreciate the vote of confidence. I do it both ways and I do agree removing the sashes makes it much lighter. I thought it was quicker to leave the sashes on, but didn’t really save that much time. I take the sashes out most of the time.
@jameslloyd8110
29 күн бұрын
@@TrueGritDevelopment thank you for the response man you did a very detailed and thorough video and I’m sure you helped out many people with this video. I have a random question. I recently measured someone’s house and I always try to get inside and outside measurements and the windows were 3 inches different on the inside then they were the outside. Have you ever ever ran across something like this?
@TrueGritDevelopment
29 күн бұрын
Mmm…if this a replacement job, I would only measure inside and go with that. On the outside you maybe catching some of the trim or whatever. I measure inside the sashes as I show in the video, so whether you’re inside or outside the measurement should match.
@jameslloyd8110
29 күн бұрын
@@TrueGritDevelopment good idea. Thank you. I mostly do apartments and keep busy but I do houses too, though not nearly as often and this is the first I’ve come across it. Every windows different but these are the strangest I’ve come across.
@davidreyna6318
3 жыл бұрын
Very good instructions. I do construction, but have never replaced windows. Thank you for this video. Am more confident doing it myself and saving tons of $.
@TrueGritDevelopment
3 жыл бұрын
Thank you sir. I appreciate the feedback. Good luck with your project.
@DaGratest816
3 жыл бұрын
Thank you. Perfect description of window flashing on a replacement window. Just failed an inspection because of this but every video I've seen was all new construction.
@TrueGritDevelopment
3 жыл бұрын
Thanks so much! Appreciate the feedback. Thanks for watching and supporting ✊🏼
@lostintime8651
2 жыл бұрын
I just bought a replacement window with a arched window on top. How do I trim that out?
@steven912
2 жыл бұрын
Thank you for this video! It was the only video where the opening wasn’t level and plus, and how you fixed it! I just had four pella 250 installed my lowes and they did an awful job! No flashing, no silicone, no insulation (and it needed it-they just used latex to fill in), left the skirts falling off on the front and no shimming. Very disappointed and will take them out and do it myself. The only reason I wanted to pay someone was because I wanted to have the exterior tripped aluminum wrapped (or capped). I did find a website that has pre shaped aluminum for windows and doors and I would be able to do it myself. Thank you again for this very helpful video!
@TrueGritDevelopment
2 жыл бұрын
I am glad you found it helpful. You are so right, many contractors will skip the flashing tape and forego insulation to make the job go faster. Good luck with your project. Thanks for watching 👊🏼
@dontaedozier2945
2 жыл бұрын
What’s the website for the pre shaped aluminum
@steven912
2 жыл бұрын
I ordered mine and it is so much cheaper than paying to have it done.
@jackbolt7163
6 ай бұрын
Hey brother, I'm going to be replacing some windows and after watching your videos,I feel confidant I can do it. Thank you for your expertise!
@TrueGritDevelopment
6 ай бұрын
Glad to help. Start with bottom floor and early in the day just in the event you run into complications. Overall it’s a pretty simple job and once you get the first one under your belt, it smooth sailing. Watch my other video on replacing United windows from Lowe’s, in that video I remove the sashes, just so you can see both ways on how to replace the windows. Good luck 👊🏼
@ScottyLo
Жыл бұрын
Very helpful video. Doesn’t look too bad. I’d treat each window as a little project and 27 windows later I’d have it down.
@TrueGritDevelopment
Жыл бұрын
It will go faster than you think. You can do 4 at a time, just start early. Thanks for watching 👊🏼
@spintius3752
Жыл бұрын
This is by far the best instruction video in installing replacement windows. Wish you showed the measurement a little closer to the measuring tape. Nevertheless, thanks for the great video!
@TrueGritDevelopment
Жыл бұрын
Thank you! Which measurement, maybe I can help. Thanks for watching 👊🏼
@thehound1359
11 ай бұрын
Easily the best explanation on how to do this.
@TrueGritDevelopment
11 ай бұрын
Appreciate that, thanks for the positive feedback. Glad you found it helpful 👊🏼
@benbrisson3919
2 жыл бұрын
Your video helped me...I've almost got the courage to start the window replacement. Thanks True grit
@TrueGritDevelopment
2 жыл бұрын
Glad it helped! Go for it, make sure you start early and pick a dry day in case it takes you longer to finish. It will not take you long, good luck. Thanks for watching and supporting 👊🏼
@jacobamick7517
2 жыл бұрын
Hey! I was watching your video and felt very informed, I will say you can put a small tech screw in the top of the canister
@TrueGritDevelopment
2 жыл бұрын
Thank you, glad you found it helpful. Consider subscribing to channel, your support is appreciated ✊🏼
@TrapperWorks
3 ай бұрын
This is absurdly helpful. Thank you!!
@TrueGritDevelopment
3 ай бұрын
Thank you 🙏🏼
@danmarc149
3 жыл бұрын
Gave me more confidence to do my window!
@TrueGritDevelopment
3 жыл бұрын
I am glad. Take your time, plan it out and execute. Thanks for watching and supporting ✊🏼
@smosely4214
Жыл бұрын
Awesome video man. Agree all the great comments below. Well done!
@TrueGritDevelopment
Жыл бұрын
Much appreciated man 👊🏼
@Zazai101
3 ай бұрын
Amazing, thanks for sharing your experience. Helped me a lot.
@TrueGritDevelopment
3 ай бұрын
Glad to hear it! Thanks for watching 👊🏼
@sameralzuhairi823
3 жыл бұрын
thank you for sharing your experience that was helpful 😊
@TrueGritDevelopment
3 жыл бұрын
Thanks for watching and supporting ✊🏼
@kelvinolivas7558
2 жыл бұрын
Best video out there and in detail thanks
@TrueGritDevelopment
2 жыл бұрын
Thank you for your positive feedback 👊🏼
@handyrandy1973
2 жыл бұрын
Outstanding video! Thanks for the tips!
@TrueGritDevelopment
2 жыл бұрын
Thank you! Glad you found it helpful.
@roberthernandez7538
3 жыл бұрын
Just installed my 12 windows only 9 more to go. Thanks for the tips...
@TrueGritDevelopment
3 жыл бұрын
That’s great! So satisfying when you know you’ve just saved hundreds if not thousands of dollars in installation costs. Thanks for watching and supporting ✊🏼
@KennyOlson
Жыл бұрын
This pocket replacement is almost exactly what I'm dealing with. You're giving a new homeowner confidence to do this myself and save a ton of money. Cheers!
@TrueGritDevelopment
Жыл бұрын
Glad to hear it. Thanks for watching, pls like and share 👊🏼
@johnnyk617
15 күн бұрын
Awesome video
@TrueGritDevelopment
15 күн бұрын
Thanks!
@ambroseteas
Ай бұрын
Right great work thanks
@TrueGritDevelopment
Ай бұрын
Thank you 🙏🏼
@gordonfuentes808
2 жыл бұрын
Awesome video very educational my brada 💯🤙🏽😎 Mahaloz 🏝👊🏽
@TrueGritDevelopment
2 жыл бұрын
I appreciate the love, Mahaloz ✊🏼
@jimmylee1376
9 ай бұрын
I just had these same windows installed in my garage. Your video was great, however the one thing I was hoping to see was how to best reinstall the screens. The full length screens that the windows come with don't seem to go back in easily. Any tips for how best to reinstall the screens?
@TrueGritDevelopment
9 ай бұрын
Thank you. You should have the little black inserts on the sides? If you do, the screen should fit snug, you may have to get one side in first and pull on the other side.
@emilyarby9807
2 жыл бұрын
Wonderful video! Thank You!
@TrueGritDevelopment
2 жыл бұрын
Thank you so much! I appreciate the support ✊🏼
@duanebailey5447
4 ай бұрын
Thanks for the video!. Question, if you caulk the skirt of the window, won't any water that gets expelled through the weep holes get trapped inside ?
@TrueGritDevelopment
4 ай бұрын
When you caulk ensure you’re not blocking any of the holes. Your caulk should go underneath.
@duanebailey5447
4 ай бұрын
@@TrueGritDevelopment Thanks, that is what I did, but I noticed the weep holes are higher in the base of the window. So if water runs down the window into the weep holes and you caulk the bottom of the skirt then there is no where for the water to escape. I'll keep an eye on the weep holes and see if they fill up. If so I'll drill a few small holes in the caulking at the base of the skirt.
@TrueGritDevelopment
4 ай бұрын
Oh ok, I see what you mean now. No need to caulk the skirt.
@kimlucianovic5671
2 жыл бұрын
This is just what I needed! Pella didn't help at all. What the heck was that skinny pie e? Oh. You explained the skirt and how to attach it. Why can't Pella just say that? Thanks
@TrueGritDevelopment
2 жыл бұрын
Glad it helped. Exactly why I made the video. It was stunned Pella didn’t have any gd instructional videos out there. Thanks for the feedback and support 👊🏼
@chiefbiglew
8 ай бұрын
most of the time where he first measured the window that is like a piece of shoe mold that will pry off then your window will go in .but the way i do it is when he put the window in from the inside the part the window went up against on the outside you dont have to remove the sashes just cut that part off flush with the brickmold from top to bottem take the strips out then the window will come out from the outside and you dont have to take your trim off on the insde whitch can couse problems it never goes back on in the same place you risk tearing the drywall paper if you dont cut the caulk rite .put the window in up tight to your inside trim level insulate put the strips that you cut out with the sawzall a little sanding caulk and paint your done. replaced hundreds this way but i normaly wrap them with coil on the outside.
@TrueGritDevelopment
8 ай бұрын
Definitely an option. It will be difficult on higher floors working on a ladder especially when you’re working solo.
@kerrim2905
2 жыл бұрын
Thank you for this, it was very helpful! I am going to pick up my replacement window tonight and was just wondering if I can do this same procedure on a second story window, from the inside? I am pretty scared that I will put the window in and it'll fall out and plummet to the ground! The window guy said I should rent scaffolding and replace it from the outside but I'm thinking this is much easier!
@TrueGritDevelopment
2 жыл бұрын
Glad you found it helpful! You absolutely can. It’s the same procedure. The outside trim will stop the window from going anywhere as long as your measurements are accurate. Thanks for watching and supporting ✊🏼
@leigroupllc
27 күн бұрын
Could they be installed from the outside as I want to replace the brick molding?
@TrueGritDevelopment
27 күн бұрын
Anything is possible but not ideal IMO especially if you have 2nd or 3rd flr windows. I would replace the brick moulding after installing the windows.
@thegreatseal4252
2 жыл бұрын
Thanks for the advice but I had a question. How do you open up the screen or pop it open
@TrueGritDevelopment
2 жыл бұрын
My pleasure. Usually there is a loop at each corner or pins on each side, I can’t remember which, but I am thinking these had the pins. Once you pull the pin, you should be able to pop the screen out or move up/down. Hope this answers your question. Thanks for watching and supporting ✊🏼
@thegreatseal4252
2 жыл бұрын
@@TrueGritDevelopment thanks!
@IMEMINE.
2 жыл бұрын
Very informative Great video
@TrueGritDevelopment
2 жыл бұрын
Thanks for watching and supporting ✊🏼
@carolhildebrand8360
10 ай бұрын
The Pella 150 series has a large flat head screw id way on the outside of the fram,:What is it used for?
@TrueGritDevelopment
10 ай бұрын
Watch my United window video I show what that is used for. Basically, on the I side of the frame there the other end of that screw head where you can use a flat head screw to push that head in/out. It’s used to tighten or loosen the window frame against the wall framing. So, if your window sash is too tight, you can loosen the frame and visa versa. It’s much clearer in the video kzitem.info/news/bejne/uYGZ05irjZeDZYIsi=rbWHGe7_2hbe9aIm
@MelissaCox-MC22
3 ай бұрын
Great video!
@TrueGritDevelopment
3 ай бұрын
Thank you!
@paulhague2376
2 жыл бұрын
Thanks for the video very helpful. Do I have to use the spray foam????? Or can I use some else.
@TrueGritDevelopment
2 жыл бұрын
Glad you found it helpful! Some else is all good. The nice thing about foam is it goes into all the nooks and crannies. You can use batt insulation too. Thanks for watching and supporting ✊🏼
@papawsgaming8762
Жыл бұрын
there is a U shaped plastic piece that you had left over..what is that for? I installed this same window and was confused as to its purpose..shipping protection maybe. Was kinda wondering if that is used to place over the base when you're using a window air conditioner?
@TrueGritDevelopment
Жыл бұрын
That piece can be used on the top of the window. You can use it if you have a gap between the top of the window and the window frame. It’s a tight fit normally, so often it gets tossed. Next time I install a Pella I’ll make a video and explain. Sub the channel if u want, so u can check it out when I post. Thanks for watching 👊🏼
@papawsgaming8762
Жыл бұрын
@@TrueGritDevelopment oh ok, ya i didnt need to use it..ill sub. thx
@TrueGritDevelopment
Жыл бұрын
Great! Thanks.
@jenifergarcia3701
3 жыл бұрын
Hi, just a question about a past video regarding the Ramset. I was curious about shooting into cinder block and you said yes and demonstrated it. What type of nail did you use, wondering what type of head it had. I’m wanting to do the board and batten look on the exterior of my stuccoed house…. But skip the board and only batten. I was wanting to glue the batten and shoot a few nails in. Looks like it’s a go…. Curious if you agree? Thanks so much! Your videos are all nicely done!
@TrueGritDevelopment
3 жыл бұрын
Hi! I used the yellow tip bullets, check the description in the video for more detail. My only concern with shooting into stucco is the stucco might break apart as your shoot through it, If that is not a concern, then I don’t see why you can’t. Thanks for watching and supporting ✊🏼
@markcroteau9690
2 жыл бұрын
This is a great instruction video on replacement windows! Are these instructions the same for the Pella 250 series windows?
@TrueGritDevelopment
2 жыл бұрын
Thank you. Pocket replacement windows are all the same. There may be some minor differences as in how the trim pieces connect, but replacing a window is the same. Pls consider supporting the channel by liking the video and/or subbing to channel, it goes a long way. Thank you for your support 👊🏼
@Panamera2014
2 жыл бұрын
Great video. In my case, I am looking to replace original vinyl windows with new. The old vinyl windows have a plastic sill similar to what you show on the Pellas. Am I correct in thinking I need to measure from top to whatever wood sits beneath that plastic sill? Not certain I can pry that piece out, maybe just cut some of it away to take measurements??
@TrueGritDevelopment
2 жыл бұрын
Thank you! The objective is to get as close a measure to the opening frame of the window. Keep in mind that you will Often be a little off and that’s ok as long as you are smaller than the frame, the gaps can be shimmed, filled in and capped with trim. You do NOT want to be smaller than the outside trim, meaning your window should still be larger than the outside opening, so the outside trim can keep it in place. Open the bottom sash and measure from the inside near you. Repeat same for top sash OR measure to the very top of the window and add 1/4”. I hope I didn’t confuse you. Some vinyl windows are different than others. If you’re in doubt, you can purchase 2 windows with varying heights and return the one you don’t use. Start the project early, so you’re not stuck without a window. Window sizes are standard, so I am sure you’ll find what you’re looking for. Let me know how you make out. Thanks for watching 👊🏽
@bhadz100
10 ай бұрын
Hi, what if I have exterior storm windows, once I remove that there will be an expose section previously covered by the frame of the storms. What can I use to cover that?
@TrueGritDevelopment
10 ай бұрын
The storm windows are typically screwed onto the wooden trim, if you’re not capping the wood, you simply fill in the holes with compound, wood filler or caulk and paint them over.
@bhadz100
10 ай бұрын
@@TrueGritDevelopment would it look weird if there is a wood portion exposed once I remove the storms and it has aluminum cap around?
@TrueGritDevelopment
10 ай бұрын
The aluminum capping covers the wood. To be clear, the capping is separate from the window. Capping is done by a contractor and they use aluminum to cover all exposed wood. It’s optional, so you can keep the wood just fill and paint.
@melissiataylor6676
2 жыл бұрын
What is the wider white channel that you laid to the side I never saw you use it
@TrueGritDevelopment
2 жыл бұрын
That is meant to go on the top of the window as a cap trim piece. Many times the window opening is too tight to allow for it, so I don’t use it or I cut out one end (convert from U channel to L) and stick it after the window is placed into position, so to use it as an interior trim piece covering gap between window and frame. Hope I didn’t confuse you. I am installing a cpl windows in the near future and will make a video specifically for that as many ppl have asked the same question. Subscribe so you’re notified when that video comes out. Thanks for watching and supporting 👊🏼
@lauraclingan2971
3 жыл бұрын
I'm in the process of replacing the window in my workshop and I was a little uncertain about the process of actually shimming and attaching the window. Also, what the heck do I do with these 2 extra (trim?) pieces included with the window? Thankfully I found your video and I'm ready to go out and finish the job! Looks like you didn't use the wider trim piece that came with the window which I assume goes on the top but I'm not sure how or why. Can you elaborate? Thanks!
@TrueGritDevelopment
3 жыл бұрын
That’s great! Two reasons I made the video: 1. No elaborate instructions with the packaging, 2. Pella can do a much better job with their so called tutorial videos. Anyway, glad you asked. For that particular window I didn’t use the top trim piece b/c I was really tight to the framing. It’s not an end all be all, b/c the window sits inside the framing and the stop trim (when properly caulked) will stop any water from going through, in addition, as part of water proofing, your exterior window framing should have a drip edge or trimming that will redirect water away from the window. To sum it up, the top trim piece IMO is designed to keep water away; however, given the above may not be necessary. I do use it when I can and I simply jam it in the hair line opening b/n top of window and frame as it’s quite flexible. Hope this answers your question. Thanks for watching and supporting ✊🏼
@zehuazhou3390
Жыл бұрын
Thank you for the video. I just received a Lowes delivery of a 100 inch wide window and it is really heavy (200 lbs). I wonder if the installation process would be the same?
@TrueGritDevelopment
Жыл бұрын
That’s a beast lol. If it’s a pocket window, yes. You would want to shim every 25” along the top and also the bottom to ensure the frame won’t sag since it’s so big. Good luck!
@zehuazhou3390
Жыл бұрын
@@TrueGritDevelopment Thank you! I have to rebuild the wall as well because the current wall is a floating wall which would not support this heavy window, so hopefully I would be able to make the bottom perfectly level so I don't need shims on the bottom. Could you give any tips for how I could life this heavy window up? It is a first floor installation but I still need to lift it up by 3 feet from the ground. Should I call a furniture mover for help?
@TrueGritDevelopment
Жыл бұрын
Got it. I would get help. It’s a big window. You don’t need skilled labor, just any set of hands to help you lift it.
@zehuazhou3390
Жыл бұрын
@@TrueGritDevelopment Do you know if this kind of window have required side to be up? I can tell which side should face outside, but can't tell which side should be up. It slides sideways. I would assume the bottom side should have weeping holes but with the packaging, it is hard to see. And what kind of screw do you recommend to use to drill into the two sides to mount it? Do I just drill holes on the two sides? Or is there a plastic cover that I need to take off?
@TrueGritDevelopment
Жыл бұрын
It’s hard for me to tell without the window model number. I would recommend checking the manufacture website maybe? If you don’t see screw holes, you can drill your own and use a flat head screw.
@mannylo480
2 жыл бұрын
Thanks for the vid, hope you still respond this question. My old windows don't have outside trim, instead it has storm window to hold outside and work as outside trim. Is it harder to work with inside trim only? Thanks
@TrueGritDevelopment
2 жыл бұрын
You welcome! Are you keeping the storm windows? I would personally not keep them as they are known to trap water and moisture. What are the storm windows screwed onto? Window frame? How is your window terminated at siding? And to answer your question, no it’s not hard to work from outside unless this is a second floor and you have to get up on a ladder. You basically reverse the installation. However, be mindful that your replacement window may be smaller than the original and will leave a gap on the outside, so you will have to do trim. What kind of siding to you have? I know, too many questions.
@steven912
2 жыл бұрын
The one question I have is about new install vs replacement. Since I want to cap the exterior wood trim. Is it possible to take off the exterior trim/casing and install a new window (with nailing flange), flash/caulk and then reinstall the exterior trim?
@TrueGritDevelopment
2 жыл бұрын
Good question. It depends on how wide is your trim and how wide is the flange for the window. I would check the window flange first and then you can decide. To answer your question though, yes you can if you had enough room. Thanks for watching 👊🏼
@pavlo5877
Жыл бұрын
Is it normal if my existing widow is 4 9/16” deep but replacement window is only 3 1/2” deep?
@TrueGritDevelopment
Жыл бұрын
You would need to get a 4.5 window jamb replacement window not 3.5 unless you are replacing your 4.5 by 3.5. You will then have a deeper recess or inset window and more finish work as in drywall or trim work. Hope this answers your question. Thanks for watching 👊🏽
@lazyxj
2 жыл бұрын
How many inches our your scribe molding? I have a very big gap on one side and I don’t know to do? It was my first time installing replacement window.
@TrueGritDevelopment
2 жыл бұрын
My scribe was a typical scribe, maybe 1/2”. You can remove the top and bottom casing, cut it back and move the side casing over to cover the gap. The drawback is you may have to refinish and/or paint the wall where you move the casing over. Alternatively, you can get wider casing, but that may look funky. Hope this helps. Thanks for watching and supporting ✊🏼
@BlackieMiles1
2 жыл бұрын
Good information. Use fixed video versus body cam.
@TrueGritDevelopment
2 жыл бұрын
Thank you. It’s hard to show details with a fixed cam unless I stop and move the cam every time. Wish I had a videographer. Thanks for watching 👊🏽
@kateyoungheeku2595
2 жыл бұрын
Thank you so much for the video, It is very helpful! Can I install screen door with the vinyl window?
@TrueGritDevelopment
2 жыл бұрын
My pleasure. Do you mean a window screen? Not sure I understand the question, sorry.
@octomo5564
2 жыл бұрын
Great video
@TrueGritDevelopment
2 жыл бұрын
Thank you! Glad you found it helpful!
@nightowl1654
5 күн бұрын
What screws you used?
@TrueGritDevelopment
5 күн бұрын
Pan head screws 👍🏼
@nightowl1654
4 күн бұрын
@@TrueGritDevelopment what size?
@TrueGritDevelopment
4 күн бұрын
2-2/12 depends how tight the window is to framing. Go with 2 1/2
@bbiz1642
8 ай бұрын
Very good video
@TrueGritDevelopment
8 ай бұрын
Thank you! Glad it was helpful.
@michaelervanian3074
2 жыл бұрын
Great video! Quick question. After the install, do you go outside and caulk where the window frame meets the existing exterior trim? I know you put silicone on the back side of the trim and press the window into it, but is there a chance that any water can get in and rot the trim from the inside? If I'm not explaining this well, you run your finger along the trim piece I'm asking about right around 7:04. Thanks!
@TrueGritDevelopment
2 жыл бұрын
Thank you, glad it helped. Lol at min 7:29 I mention that I run a beed of caulk along the trim, so yes. Always advisable to seal where two surfaces meet. Thanks for watching and supporting ✊🏼
@michaelervanian3074
2 жыл бұрын
@@TrueGritDevelopment must have missed that the first time. Thanks again!
@TrueGritDevelopment
2 жыл бұрын
You bet. Good luck with your project!
@funnelnutz3227
2 жыл бұрын
Yes we always caulk the stops in the pocket and the outside
@ailhalawe3599
3 жыл бұрын
عاشت ايدك
@nolansnerfarena3422
Жыл бұрын
Awesome. Thanks
@TrueGritDevelopment
Жыл бұрын
Glad you found it helpful 👊🏼
@pootthatbak2578
2 жыл бұрын
What's up with that plastic cover that came inside the window package it was laying on top when i opened it?
@TrueGritDevelopment
2 жыл бұрын
It’s the header trim. It’s used to cover any gaps that you may have above the window. Most of the time it’s not used as the gap is too small and the trim can’t fit. It’s supposed to sit on top of the window. Hope this answers your question. Thanks for watching 👊🏼
@pootthatbak2578
2 жыл бұрын
@@TrueGritDevelopment thanks..you have confirmed what i thought. No help from pella unless you log in and register. I think pella scrubs the web of videos, or videos are naturally rare. Most pella owners probably hire installers, i imagine. i winged it last night and the window fits, would not have fit with that top cap. Lol youre right about the bottom sash gap cover. Cant get mine on..may need trimming
@TrueGritDevelopment
2 жыл бұрын
Dude, I had contractors install 23 windows in my house and they didn’t do anything different. As long as you have the window secured, squared and sealed you’re good. It’s highway robbery charging over $700/window. To clarify, the bottom trim (I called it skirt) should fit snug into the groove. Only trim it if you have to. When caulking, be careful not to block the drip holes.
@pootthatbak2578
2 жыл бұрын
@@TrueGritDevelopment i got out the fine scale and measuring devices. I measured 4 times. I determined the bottom of the " skirt was needing a trim, if the grooves were to line up. I ran the bottom edge over my rigid jointer. Shaved the skirt 3 /32" . It then fit. Used a block of wood to push it in. It is a very tight fit. My sill was angled 13 degrees a steeper angle would have helped. The skirt has probably caused many people alot of grief
@robertchampion4172
Жыл бұрын
nice job
@TrueGritDevelopment
Жыл бұрын
Thank you sir.
@hyperqbit7246
3 жыл бұрын
What do you fo with the too cover of the new vinyl window? Saw it tossed aside
@TrueGritDevelopment
3 жыл бұрын
the top trim piece IMO is to fill in the gap between top of window and frame. I do use it when I can and I simply jam it in the hair line opening b/n top of window and frame as it’s quite flexible. Hope this answers your question. Thanks for watching and supporting ✊🏼
@weekendhomeprojects
Жыл бұрын
Great channel man! Just sub'd.
@TrueGritDevelopment
Жыл бұрын
Yours ain’t bad either. Got u back under different acct. 👊🏽
@weekendhomeprojects
Жыл бұрын
@@TrueGritDevelopment Much appreciated.
@bhadz100
3 жыл бұрын
What kind of screws and size did you use?
@TrueGritDevelopment
3 жыл бұрын
The screws came with the window. Sorry if I did not take a shot of them in the video. Thanks for watching and supporting ✊🏼
@badtheba
3 ай бұрын
I’d be really concerned about water intrusion on the outside. That flashing tape basically did nothing but cover the middle of the wall framing. It did nothing to direct water out and down.
@TrueGritDevelopment
3 ай бұрын
The flashing tape is meant to protect the corners and bottom framing from rot. The outside trim and silicone caulk is your primary line of defense.
@badtheba
3 ай бұрын
@@TrueGritDevelopment the outside frame/trim is still higher than the wall framing and the bottom of the new replacement window. Water needs to be directed out and down, that is not accomplished here even with the outer snap on strip.
@nickbrockelman
6 ай бұрын
Foam can is used upside down
@TrueGritDevelopment
6 ай бұрын
Worked for me, but noted. Thanks for watching 👊🏼
@nickbrockelman
6 ай бұрын
@TrueGritDevelopment yes it will work for a while but you won't get all of the foam out of the can. You won't have enough propellant to push out all of the foam and you'll have to throw it out. Can't even use the air compressor hack with foam.
@TrueGritDevelopment
6 ай бұрын
Got it. Always gd to learn.
@sdmairs2386
2 жыл бұрын
Your measuring points for the height aren't clear.
@TrueGritDevelopment
2 жыл бұрын
All you need is to measure from the sill to the top of the window frame. You can round up, so if you’re off by 1/8” or 1/4” they are usually standard sizes. What you don’t want to do is get a larger window. Hope this helps. Thanks for watching 👊🏽
@jonsisk87
2 жыл бұрын
Backer rod and caulking. No more great stuff going bad
@TrueGritDevelopment
2 жыл бұрын
Backer rod is a gd one. Thanks for watching 👊🏽
@victorvek5227
2 жыл бұрын
Putting back that old shit trim ruined it for me. New window with old trim is the worst.
@TrueGritDevelopment
2 жыл бұрын
New trim would be nice. It’s hard when you have to stick to a budget though. I believe this was a 19 window project. Thanks for watching and supporting ✊🏼
@xAiMz
2 жыл бұрын
Wouldn’t you wanna double check the window before demo Lolol
@TrueGritDevelopment
2 жыл бұрын
You must measure window before ordering or purchasing windows. I go over measurement early into the video. There are standard window sizes and most of the time you will find them stocked with slight variations of 1/2” or 1/4”. You may have to special order sizes too. Either way, measure first. Hope this answers your question. Thanks for watching and supporting ✊🏼
@robertsmith3518
Жыл бұрын
You did a pretty good job till you decided to hang the old trim , then you would have been fired . You showed your true workmanship ability ,that was piss poor at best. Next
@TrueGritDevelopment
Жыл бұрын
Thanks. Just a preference to reuse the old trim. Save more $$. Has nothing to do with installing the actual window. Piss poor workmanship at best is a little harsh on your part, but all good. Thanks for your feedback.
@Elvampiro.
Жыл бұрын
Looked trashed
@TrueGritDevelopment
Жыл бұрын
👍🏼
@dicko195
Жыл бұрын
OMG move your fingers out of the way of the knife @9:38
@TrueGritDevelopment
Жыл бұрын
I am cutting along then wood frame, but yea it looks like I am about to slice my finger lol
@matthewsottile8877
2 жыл бұрын
I am doing my first pella 150 replacement window in my house. Their online directions are bad. Your video has been a tremendous help, very well done and a huge help to me thanks so much matty
@TrueGritDevelopment
2 жыл бұрын
Good luck buddy! Thanks for the positive feedback. It’s pretty easy once you get the hang of it. 👊🏼
@prettyboyfloyd76
8 ай бұрын
@@TrueGritDevelopmentcan you get pella replacement with for exiting vinyl new construction windows on vinyl siding?
@adb99999999999
Жыл бұрын
Excellent tutorial, but you need to (1) caulk the outside where the existing blind stop meets the replacement window frame and (2) cut a 1/4” weep hole in each end of the sill adapter (skirt), 1” from each end. I also prefer to caulk the sill adapter to the existing sill to minimize wind, bug, and rain intrusion. You’ve got a back dam of caulk between the frame and the stool, but keeping stuff out is generally better than relying entirely on caulk near the interior. Also, the sill adapter won’t always be a perfect fit in either height or width. It has two score lines on the back to trim it to height, and I find that a large pair of end nippers is perfect for cutting the ends to length. Installing it from the outside after trimming to fit is a little more difficult, but a rubber mallet or dead blow hammer and a plastic tapping block works wonders.
@TrueGritDevelopment
Жыл бұрын
Thanks for the feedback 👊🏼
@robburkhard9256
Жыл бұрын
I've never heard of weep hole in the sill adapter, how does that work? Especially if you are trying to secure it from wind, rain and "bugs".
@derekjohnson4129
2 жыл бұрын
Great video, thanks for sharing. I don't have a lot of experience replacing windows, and I'm in a similar situation where I have a really tight fit height wise. Once I attached the skirt, I have almost no room above or below. Other videos have said you must shim the bottom, but you say it wouldn't be necessary if its level. Are you not concerned with spraying foam above and below the window, or is the flashing and caulk good enough there? Thanks!
@TrueGritDevelopment
2 жыл бұрын
So shimming the bottom is necessary to level the window. If your window opening is level, no need for a shim. The window is not going anywhere once you have it screwed to your framing. Foam is for insulation purposes, I use it b/n the window and framing to fill in any open gaps for added insulation. You certainly can use it anywhere as long as it doesn’t create pressure that may interfere with the operation of the window. In my case I didn’t have any room at the top to insulate. On some windows I actually was able to put the top trim piece on and that covered any gaps I had. I will be putting out another video specifically addressing the top trim piece that came with the window, many viewers ask about it. I hope that answers your question. Thanks for watching and supporting ✊🏼
@luisbeltran4137
Жыл бұрын
April 24, 2023 Im replacing two windows today and you built a great confidence in me to do it myself thank you so much!!!
@TrueGritDevelopment
Жыл бұрын
Glad to hear it. Start early and take your time. Once you have the first under your belt, it’s smooth sailing. Good luck 👊🏼
@frankgollahon4947
2 жыл бұрын
i replace 3 windows didnt know about the skirt ,,what does it do? i left them out ..nice video
@TrueGritDevelopment
2 жыл бұрын
They go at the bottom of the window. They are meant to cover the gap b/n bottom of window and sill. Hope this answers your question. Thanks for watching and supporting 👊🏼
@MRrwmac
2 жыл бұрын
Very well done on the video and narration/instruction! I’ve heaerd lots of bad things about replacing my 30 year old windows with pocket windows (like you have done here), but I dont want to replace my lap siding. My windows have lasted 30 + years but a couple would have lasted longer had I donr better maintenance and paining more often. The expensive Pella says it will take 4 months before I can get another 50” x ’50” window. I dont think the ones in stock from Lowes and Home depot are a very good quality. What do you think? Thanks again, for a great well made video!
@TrueGritDevelopment
2 жыл бұрын
Thank you for the positive feedback. The best I can say about the series 150 sold at big retailers is that they are developer grade windows, so they will meet energy efficiency requirements, operate as intended and will last a while. The difference with other higher quality windows is the framing (some come with thicker frames with added support), the little parts used to operate the window (made of higher grade plastic) and the seal. However, the seal is usually covered under warranty. What makes the biggest difference IMO is the installation job. As long as you install the window square and water proof the framing (I mean the house framing) you will get many yrs out of these windows. Hope this answers your question. Thanks for watching and supporting 👊🏼
@MAGAMAN
Жыл бұрын
I could see light from the outside coming through your window frame when you were putting in the spray foam. This means you have a place where water can enter around your window. You also don't any yo use normal spray foam because it can push your window out of square (I have seen people use this stuff to raise a sidewalk!) and cause all kinds of problems. You want to use the stuff designed for around windows and doors.
@TrueGritDevelopment
Жыл бұрын
Once you’re finished inside, you want to finish outside. I silicone caulked all around the windows. In a cpl of those windows I swapped the exterior trim for Azek, so this may have been one of them. You are correct with the foam stuff, it can expand like crazy. If you notice I only put just enough, gd point though. Thanks
@JoeGriffith-cp1io
Жыл бұрын
No wonder you have so many views. I was pretty confident in the first place. You made me realize many of the labor-intensive procedures I was going to do aren't necessary. I am going to have much repair to do. I live in an old country schoolhouse built in 1917. It had extra classrooms and plumbing in the early 50s. then was converted to a home in the early 60s, that's when these windows were installed. Anyway, I'm rambling, what I wanted to say is brother you ROCK!!! I'm sure I'll watch a few more times. I have 14 windows to install and massive amounts of rot to repair so the time you saved me is much appreciated.
@TrueGritDevelopment
Жыл бұрын
I am glad you found it helpful, please like and share. Once you get started it’s pretty easy and straight forward. Let me know how your project goes. Good luck.
@MarkCartret
Жыл бұрын
There is a much easier way to install that as a replacement window. Granted much of what you must work with is whatever the prior installer/builder put in. Mighty brave banging on the finished wood with a hammer head. Use a block of wood or rubber mallet next time. But you did an excellent job otherwise.
@TrueGritDevelopment
Жыл бұрын
Thanks man. I just installed 9 windows for another flip property and I took the sashes out this time. Much lighter to work this way, is this what you meant by another way?
@MarkCartret
Жыл бұрын
@@TrueGritDevelopment also take the outside trim off, but save it for reuse. You may be able to leave the inside trim molding and pull the window out from the outside, slip in the replacement, plumb and level and reinstall the exterior molding. Generally 30 minutes tops.
@TrueGritDevelopment
Жыл бұрын
You could do that for first floor windows maybe, but not 2nd or 3rd flrs! Don’t know about you, but I don’t like working on ladders. Also, some windows may be located in a cove or inset without interior trim, so you won’t have a stop. Check out my other install video for United window and door also from Lowe’s.
@MarkCartret
Жыл бұрын
Gotcha.
@jwojo7644
Ай бұрын
I have pella 250 replacement windows would this be the same process. I paid a “contractor” to do it and it’s a complete hack job with gaps and play everywhere because he did not shim and won’t fix his work states he never heard of using shims on a window
@TrueGritDevelopment
Ай бұрын
Yes, similar installation. Contractors are infamous with not using shims. They usually want to go in/out as quickly as possible. It’s important to have the window level and square. Good luck.
@JT_IBX
Жыл бұрын
Thank you for the information. That's the replacement window I decided to buy, as they are on the shelf at Lowe's home improvement store. The part that answered my question was that the window came with a piece of trim that connects the bottom of the window to the slope of the sill. I thought I would have to make a wage molding or whatever to accommodate the space under the replacement window. Very informative video. Thanks, I now feel more confident buying six of those windows and doing the installation myself.
@TrueGritDevelopment
Жыл бұрын
Thank you! Once you get one in, you will find it easier and easier. Good luck and thanks for watching 👊🏼
@krisallen9194
Ай бұрын
Great video. I flip houses myself. Curious to why you replaced the window in the first place ?
@TrueGritDevelopment
Ай бұрын
Thank you. They were older wooden windows, some didn’t operate well and others were not lined up right and figured from a resale standpoint point the house will be worth more.
@davetaylor2449
Жыл бұрын
The windows I am replacing are Anderson windows. I gather that replacement windows use your windows existing outside sill. Well my outside sill are so thin you could poke your finger through it, that’s mostly why I am replacing them. So want can be done?
@TrueGritDevelopment
Жыл бұрын
Hi Dave, so have you determined the cause of the damaged sills are the windows? Is it because they were poorly installed? I ask b/c if it’s the install, u can re-use your window after you repair the framing. Anyway, to answer your question, I would replace the sill if it’s damaged. You will need an oscillating tool, Pry bar and a hammer. Replace it with similar size piece as the original. I’ve had jobs where I replaced the framing 2x4 underneath the sill, flashed, replaced the window then finished with exterior trim, so it really depends what you have there. Hope this answers your question.
@kamiperzsi7495
8 ай бұрын
2 questions: So you don't need to screw the top or the bottom? And the large piece in the beginning of the video that you set aside with the small trim, that doesn't get used ??
@TrueGritDevelopment
8 ай бұрын
Nope, no need to screw top Or bottom. The trim piece can be used over the top of the window, but you often will have no space for it. It’s meant to seal the gap between the top of the window and the framing; however, in my experience that gap is usually around 1/8” and can be caulked. I have used it in the past and do intend on making a video because many ppl had the same question. Hope this answers your question.
@edwardmolocznik9017
8 ай бұрын
Well done on this video! Do you have a video on how to remove exterior flange nailed single hung vinyl windows? Will this be a different process?
@TrueGritDevelopment
8 ай бұрын
Thank you! Unfortunately I don’t have a video for that, but outside of cutting out the flange, the process is the same. What you need to do is remove exterior trim or J channel to expose the edge of the flange, then cut out the flange using a utility knife. You will have to make several passes using sharp blades. Once that’s out of the way, you’re home free. Good luck 👊🏼
@altaroxllc3184
3 жыл бұрын
Well done, very helpful. I am using the Pella windows that come with aluminum skinned sills. No more future sill rot....I hope!
@TrueGritDevelopment
3 жыл бұрын
Thanks for watching and supporting ✊🏼
@alleewengert3654
Жыл бұрын
Thank you so much for this video! My 19-pound Jack Russell saw a squirrel and jumped against the 107 year old window and shattered it. You've saved me nearly $900!! One quick question - where can I find a sill skirt? I've been looking all over and nothing looks like the one you used. Thanks!
@TrueGritDevelopment
Жыл бұрын
Oh man, hope your little one is ok. The skirt/trim comes with the window, did yours not come with one?
@hughberesford2554
11 ай бұрын
What is the purpose for using the silicone and if I need to change the window again will it not be harder to take out because of the silicone. Thanks
@TrueGritDevelopment
11 ай бұрын
Adhesion and sealing really. It will ensure the window is air tight. In the future you can switch out the sashes. If you must take out the window, the sealant won’t be a problem. There is too much leverage when you pull the window.
@RoosterSnuffer
3 ай бұрын
How do you know the bottom of your window is level? Is the bottom of that window not convex?
@TrueGritDevelopment
3 ай бұрын
You mean when you install it? Put a level and shim if necessary. The window itself should be square, but if not I would take it back.
@oblio63
Жыл бұрын
Seems like a big void under the window. Shouldn't I try to get foam behind that skirt under window?
@TrueGritDevelopment
Жыл бұрын
The bottom of the window should be flush (assuming the sill is level) with the sill if you look from inside the house. The sill should pitch away from the house, it is that gap you are referring too, correct? Do not use foam insulation as that may expand and create pressure on the bottom of the window, which will impact how the window sash operates. Instead, you may use bat insulation. In my case, I only used silicone caulk to seal the bottom of the window. Hope this answers your question. Thanks for watching 👊🏼
@TeslaRules1856
15 күн бұрын
How do you get all that exterior window trim to be matching vinyl and not wood. I guess I figured that was part of the window replacement. Don't want to ever paint the outside window trim again.
@TrueGritDevelopment
14 күн бұрын
I feel your pain, but you may not like my answer. The only way is to replace your exterior wood trim with brick molding vinyl trim, which is also not cheap. Another alternative is to have someone cap your wood trim with flashing and that can be less expensive than Vinyl brick molding.
@TeslaRules1856
14 күн бұрын
@@TrueGritDevelopment Thanks. Cost is not an issue at this point given how much I am paying for two massive front windows - and that we will be retiring in a few years and want maintenance free on home. I will ask my handyman about the two options you mention. Thank you.
@acewood7923
Жыл бұрын
You should always keep your window tight against your exterior stops and plum it in the opening ,,by pulling the bottom in as you did now, you've created and out of parallel surface with the wall to the window which you will now need an extension jamb from 3/4" at the top to a 1/2" at the bottom .
@TrueGritDevelopment
Жыл бұрын
Thanks for the feedback, noted. How do you plumb it in the opening, if say the exterior stops aren’t plumb.
@acewood7923
Жыл бұрын
You need to plumb side to side ,the in to out is not as important as long as it has a tight seal against the exterior stops.
@TrueGritDevelopment
Жыл бұрын
Got it.
@noreenosullivan1916
3 жыл бұрын
Excellent video. One suggestion would be to remind viewers to use only "window and door" Great Stuff Foam. I don't think that was mentioned.
@TrueGritDevelopment
3 жыл бұрын
Thanks for watching and supporting ✊🏼
@briant9764
2 жыл бұрын
This is one of the best videos for replacing windows. With my limits skills i think i can do it. Pella should make you there window replacement spokesman
@TrueGritDevelopment
2 жыл бұрын
Thank you! Glad you found it helpful. I hope your project goes smoothly, just give yourself enough time for your first window, it’s not difficult. Thanks for watching and supporting ✊🏼
@hathawaydj1
2 жыл бұрын
Good video. Most out there are using new construction windows... so thanks for making this one.
@TrueGritDevelopment
2 жыл бұрын
You bet! Glad u found it helpful. Thanks for watching and supporting 👊🏼
@artkits
3 жыл бұрын
Thanks for this life saver video, we had zero instructions. Is outside moulding a requirement for installing these windows? They have no flange.
@TrueGritDevelopment
3 жыл бұрын
I am glad you found it helpful. These are replacement windows not full frame replacement windows, so they don’t come with a flange. If you are replacing an existing window, chances are you already have the outside stop trim installed. If for some reason you don’t have it, you must ensure the window is plum then proceed to install the trim, which will serve as a stop trim and to hide unfinished parts of the framing and gaps b/n window and framing. You can finally dress up the job with silicone caulk and additional trim if you like. I hope this answers your question. Thanks for watching and supporting ✊🏼
@paulcoggins
2 жыл бұрын
thx so much. Saved me tons of $$$ AND time by finding this video as in my ignorance i was going to rip out all window and trim and put in new construction window.lol
@TrueGritDevelopment
2 жыл бұрын
You’re welcome! Glad you found it helpful and save $$. Thanks for watching and supporting ✊🏼
@padadge
10 ай бұрын
take that camera off your hat im getting sick
@TrueGritDevelopment
10 ай бұрын
Yea, I am sorry. I forget it’s on my head and move quickly. I am learning to move slower when I am shooting.
@timprusansky3199
4 ай бұрын
There is 4” x 32” tray, where does it go
@TrueGritDevelopment
4 ай бұрын
You must be referring to the U-shaped tray. It is designed to go on the top of the window to cover any gaps you may have between the window framing and the window. Most of the time you will not end up using it because it’s too tight to fit it in. You can discarded if the gap is very small and you can silicone caulk. Otherwise you can snap off one of end of the trim, so you get an L shaped trim and try to jam it in. I hope that makes sense.
@AverageAmish1
Жыл бұрын
Do you not caulk the top of the window?
@TrueGritDevelopment
Жыл бұрын
You will have a gap there, but you can caulk where the window meets the stop trim.
Пікірлер: 437